Fabrication of a Nickel Ferrite/Nanocellulose-Based Nanocomposite as an Active Sensing Material for the Detection of Chlorine Gas

Nanocomposites Based on Polyethylene and Nickel Ferrite: Preparation, Characterization, and Properties

Composite materials based on NiFe2O4 nanoparticles and polyethylene matrix have been synthesized by thermal decomposition to expand the application area of high-pressure polyethylene by filling it with nanoscale particles. The synthesized compositions were obtained in the form of a dark gray powder and compressed for further study According to TEM, the average particle size in composites was 2, 3, and 4 nm in samples with a filling of 10%, 20% and 30%. The concentration dependences of the specific electrical resistivity ρV, dielectric permittivity ε, saturation magnetization MS and the parameters of reflection and attenuation of microwave power of the obtained composites were investigated. The threshold for percolation in such materials is found to be within a concentration range of 20…30%. The electronic and atomic structure of composites was studied by methods of Mössbauer spectroscopy, X-ray diffraction and X-ray absorption spectroscopy. The closest atomic environment of nickel and iron in nanoparticles is close to that of crystalline NiFe2O4. The dependence of the nanoparticles size as well as the dependence of the number of tetrahedral or octahedral iron positions in nickel ferrite nanoparticles to their content in polyethylene matrix is established. It is shown that composite materials based on NiFe2O4 nanoparticles and polyethylene matrix can be used as components of electromagnetic compatibility systems.

Barley thermoplastic starch nanocomposite films reinforced with nanocellulose

Despite being one of the starch producers, barley has yet to be widely studied for thermoplastic starch applications, including nanocellulose thermoplastic composites, due to its uses in the food and beverage industries. However, only 20% of barley is used in the malting industry to produce both alcoholic and non-alcoholic beverages, and 5% is used as an ingredient in a wide variety of foods. As the fourth most important cereal in the world after wheat, corn, and rice, barley can be considered an interesting biomass source to produce biodegradable thermoplastics, stemming from its starch constitution. Therefore, this review attempts to highlight the barley starch properties and its potential utilization for nanocellulose thermoplastic starch composites. Several studies involving barley-based starch in thermoplastic production and nanocellulose reinforcement for properties enhancement are also reviewed, particularly in the attempt to provide various options to reduce and replace the uses of harmful petroleum-based plastic.

Wheat thermoplastic starch composite films reinforced with nanocellulose

The rising costs of non-renewable plastic and environmental concerns with their industrial usage have encouraged the study and development of renewable products. As an alternative, biological-based materials create a huge opportunity for a healthy and safe environment by replacing non-renewable plastic in a variety of applications. Wheat is one of the world’s most widely cultivated crops. Due to its mechanical and physical properties, wheat starch is vital in the biopolymer industry. Wheat thermoplastic starch exhibits useable properties when plasticizers, elevated temperatures and shear are present. Thus, make it very suitable to be used as packaging material. However, this material suffers from low mechanical properties, which limit its applications. Several studies looked at the feasibility of using plant components which is nanocellulose as a reinforcing agent in wheat starch thermoplastic composites. Overall, the addition of nanocellulose can improve the performance of wheat thermoplastic starch, especially for its mechanical properties. It can potentially be used in several areas of packaging and biomedical. The objective of this review is to discuss several achievements regarding wheat starch/nanocellulose-based composites. Several important aspects of the mechanical performance and the thermal properties of the composites were evaluated. The discussion on wheat starch and nanocellulose was also tackled in this review.

The Frontiers of Functionalized Nanocellulose-Based Composites and Their Application as Chemical Sensors

Chemical sensors are a rapidly developing technology that has received much attention in diverse industries such as military, medicine, environmental surveillance, automotive power and mobility, food manufacturing, infrastructure construction, product packaging and many more. The mass production of low-cost devices and components for use as chemical sensors is a major driving force for improvements in each of these industries. Recently, studies have found that using renewable and eco-friendly materials would be advantageous for both manufacturers and consumers. Thus, nanotechnology has led to the investigation of nanocellulose, an emerging and desirable bio-material for use as a chemical sensor. The inherent properties of nanocellulose, its high tensile strength, large specific surface area and good porous structure have many advantages in its use as a composite material for chemical sensors, intended to decrease response time by minimizing barriers to mass transport between an analyte and the immobilized indicator in the sensor. Besides which, the piezoelectric effect from aligned fibers in nanocellulose composites is beneficial for application in chemical sensors. Therefore, this review presents a discussion on recent progress and achievements made in the area of nanocellulose composites for chemical sensing applications. Important aspects regarding the preparation of nanocellulose composites using different functionalization with other compounds are also critically discussed in this review.

Structural Strength Analyses for Low Brass Filler Biomaterial with Anti-Trauma Effects in Articular Cartilage Scaffold Design

The existing harder biomaterial does not protect the tissue cells with blunt-force trauma effects, making it a poor choice for the articular cartilage scaffold design. Despite the traditional mechanical strengths, this study aims to discover alternative structural strengths for the scaffold supports. The metallic filler polymer reinforced method was used to fabricate the test specimen, either low brass (Cu₈₀Zn₂₀) or titanium dioxide filler, with composition weight percentages (wt.%) of 0, 2, 5, 15, and 30 in polyester urethane adhesive. The specimens were investigated for tensile, flexural, field emission scanning electron microscopy (FESEM), and X-ray diffraction (XRD) tests. The tensile and flexural test results increased with wt.%, but there were higher values for low brass filler specimens. The tensile strength curves were extended to discover an additional tensile strength occurring before 83% wt.%. The higher flexural stress was because of the Cu solvent and Zn solute substituting each other randomly. The FESEM micrograph showed a cubo-octahedron shaped structure that was similar to the AuCu₃ structure class. The XRD pattern showed two prominent peaks of 2θ of 42.6° (110) and 49.7° (200) with d-spacings of 1.138 Å and 1.010 Å, respectively, that indicated the typical face-centred cubic superlattice structure with Cu and Zn atoms. Compared to the copper, zinc, and cart brass, the low brass indicated these superlattice structures had ordered–disordered transitional states. As a result, this additional strength was created by the superlattice structure and ordered–disordered transitional states. This innovative strength has the potential to develop into an anti-trauma biomaterial for osteoarthritic patients.