BaSO4/TiO2 Microparticle Embedded in Polyvinylidene Fluoride-Co-Hexafluoropropylene/Polytetrafluoroethylene Polymer Film for Daytime Radiative Cooling

Development of Microparticle Implanted PVDF-HF Polymer Coating on Building Material for Daytime Radiative Cooling

A passive cooling method with great potential to lower space-cooling costs, counteract the urban heat island effect, and slow down worldwide warming is radiant cooling. The solutions available frequently require complex layered structures, costly products, or a reflective layer of metal to accomplish daytime radiative cooling, which restricts their applications in many avenues. Furthermore, single-layer paints have been used in attempts to accomplish passive daytime radiative cooling, but these usually require a compact coating or only exhibit limited cooling in daytime. In our study, we investigated and evaluated in daytime the surrounding cooling outcome with aid of one layer coating composed of BaSO4/TiO2 microparticles in various concentrations implanted in the PVDF-HF polymers on a concrete substrate. The 30% BaSO4/TiO2 microparticle in the PVDF-HF coating shows less solar absorbance and excessive emissivity. The value of solar reflectance is improved by employing micro-pores in the structure of PVDF polymers without noticeable effect on thermal emissivity. The 30% BaSO4/TiO2/PVDF coating is accountable for the hydrophobicity and proportionate solar reflection in the UV band, resulting in efficient solar reflectivity of about 95.0%, with emissivity of 95.1% and hydrophobicity exhibiting a 117.1° water contact angle. Also, the developed coating could cool to about 5.1 °C and 3.9 °C below the surrounding temperature beneath the average solar irradiance of 900 W/m-2. Finally, the results demonstrate that the 30% BaSO4/TiO2/PVDF-HF microparticle coating illustrates a typical figure of merit of 0.60 and is also capable of delivering outstanding dependability and harmony with the manufacturing process.

Study on the Electrical Insulation Properties of Modified PTFE at High Temperatures

During the operation of multi-electric aircraft, the polytetrafluoroethylene (PTFE) material used to insulate the aviation cable is subjected to a high electric field while working under the extreme conditions of high temperatures for a long time, which can easily cause a partial discharge and even flashover along the surface, which seriously threaten the safe operation of the aircraft. In this paper, the electrical insulation properties of PTFE were regulated via modification by the magnetron sputtering of TiO2 under high temperatures, and modified PTFE with different sputtering times was prepared. The direct current (DC) surface discharge, surface flashover, and electric aging characteristics of modified PTFE were studied under the condition of 20~200 °C, and the mechanisms by which modification by sputtering of TiO2 and high temperature influence the insulation properties were analyzed. The results show that the surface discharge intensity increases with the increase in temperature, the modification by sputtering of TiO2 can significantly inhibit the partial discharge of PTFE, and the flashover voltage first increases and then decreases with the increase in the modification time. The modification by magnetron sputtering can effectively increase the surface potential decay rate of the PTFE, increase the shallow trap energy density, effectively avoid charge accumulation, inhibit the partial discharge phenomenon, and improve the surface electrical insulation and anti-aging properties.

Development of High-Performance Flexible Radiative Cooling Film Using PDMS/TiO2 Microparticles

Radiative cooling, which cools an object below its surrounding temperature without any energy consumption, is one of the most promising techniques for zero-energy systems. In principle, the radiative cooling technique reflects incident solar energy and emits its thermal radiation energy into outer space. To achieve maximized cooling performance, it is crucial to attain high spectral reflectance in the solar spectrum (0.3-2.5 μm) and high spectral emittance in the atmospheric window (8-13 μm). Despite the development of various radiative cooling techniques such as photonic crystals and metamaterials, applying the cooling technology in practical applications remains challenging due to its low flexibility and complicated manufacturing processes. Here, we develop a high-performance radiative cooling film using PDMS/TiO2 microparticles. Specifically, the design parameters such as microparticle diameter, microparticle volume fraction, and film thickness are considered through optical analysis. Additionally, we propose a novel fabrication process using low viscosity silicone oil for practical fabrication. The fabricated film accomplishes 67.1 W/m2 of cooling power, and we also analyze the cooling performance difference depending on the fabrication process based on the measurement and optical calculation results.