The Effect of Polyterpenol Thin Film Surfaces on Bacterial Viability and Adhesion

One-step rapid formation of wrinkled fractal antibiofouling coatings from environmentally friendly, waste-derived terpenes

Wrinkled coatings are a potential drug-free method for mitigating bacterial attachment and biofilm formation on materials such as medical and food grade steel. However, their fabrication typically requires multiple steps and often the use of a stimulus to induce wrinkle formation. Here, we report a facile plasma-based method for rapid fabrication of thin (<250 nm) polymer coatings from a single environmentally friendly precursor, where wrinkle formation and fractal pattern development are controlled solely by varying the deposition time from 3 s to 60 s. We propose a mechanism behind the observed in situ development of wrinkles in plasma, as well as demonstrate how introducing specific topographical features on the surface of the substrata can result int the formation of even more complex, ordered wrinkle patterns arising from the non-uniformity of plasma when in contact with structured surfaces. Thus-fabricated wrinkled surfaces show good adhesion to substrate and an antifouling activity that is not observed in the equivalent smooth coatings and hence is attributed to the specific pattern of wrinkles.

Novel Extrapolymeric Substances Biocoating on Polyvinylidene Fluoride Membrane for Enhanced Attached Growth of Navicula incerta

Cell adhesion is always the first step in biofilm development. With the emergence of attached cultivation systems, this study aims to promote a cost-effective approach for sustainable cultivation of microalgae, Navicula incerta, by pre-coating the main substrates, commercial polyvinylidene fluoride (PVDF) membranes with its own washed algal cells and self-produced soluble extracellular polymeric substances (EPS) for strengthened biofilm development. The effects of pH value (6 to 9), cell suspension volume (10 to 30 mL), and EPS volume (10 to 50 mL) were statistically optimized by means of response surface methodology toolkit. Model outputs revealed good agreement with cell adhesion data variation less than 1% at optimized pre-coating conditions (7.20 pH, 30 mL cell suspension volume, and 50 mL EPS volume). Throughout long-term biofilm cultivation, results demonstrated that EPS pre-coating substantially improved the attached microalgae density by as high as 271% than pristine PVDF due to rougher surface and the presence of sticky exopolymer particles. Nutrients absorbed via the available EPS coating from the bulk medium made the immobilized cells to release less polysaccharides on an average of 30% less than uncoated PVDF. This work suggests that adhesive polymer binders derived from organic sources can be effectively integrated into the development of high-performance novel materials as biocoating for immobilized microalgae cultivation.

Potential of plant secondary metabolite-based polymers to enhance wound healing

There is a global epidemic of non-healing wounds. Chronic inflammation, overexpression of pro-inflammatory cytokines, oxidative stress and bacterial infection are implicated in delayed wound healing. Natural extracts are a rich source of bioactive molecules called plant secondary metabolites (PSMs) that include terpenes and phenols. These molecules may facilitate wound healing through their antioxidant, anti-inflammatory, and antibacterial activity. After briefly outlining the process of wound healing and how it is compromised in chronic wounds, this review focuses on investigating how PSMs-based polymers may improve wound healing. Best methods for incorporating PSMs into wound dressings are reviewed and critically compared. The exiting body of literature strongly suggests that PSMs-based polymers incorporated into wound dressings could have clinical value in aiding wound healing. STATEMENT OF SIGNIFICANCE: Chronic wounds develop by the persistence of inflammation, oxidative stress and infection. Chronic wounds affect the worldwide population, by reducing quality of life of patients with significant cost to healthcare systems. To help chronic wounds to heal and overcome this burden, materials with anti-inflammatory, antioxidant and antibacterial properties are required. Plant secondary metabolites (PSMs) are volatile materials that have all these properties. PSMs-based polymers can be fabricated by polymerization techniques. The present review provides an overview of the state-of-the-art of the wound healing mechanisms of PSMs. Current developments in the field of PSMs-based polymers are reviewed and their potential use as wound dressings is also covered.

Effects of Ionic Liquid, 1-Ethyl-3-methylimidazolium Chloride ([EMIM]Cl), on the Material and Electrical Characteristics of Asphaltene Thin Films

Asphaltene is a component of crude oil that has remained relatively unexplored for organic electronic applications. In this study, we report on its extraction technique from crude oil tank bottom sludge (COTBS) and its thin-film characteristics when 1-ethyl-3-methylimidazolium chloride ([EMIM]Cl) ionic liquid (IL) was introduced as dopants. The extraction technique yielded asphaltene with more than 80% carbon content. The IL resulted in asphaltene thin films with a typical root-mean-square surface roughness of 4 nm, suitable for organic electronic applications. The thin films each showed an optical band gap of 3.8 eV and a sheet resistance as low as 105 Ω/□. When the film was used as a conductive layer in organic field-effect transistors (OFET), it exhibited hole and electron conduction with hole (µh) and electron (µe) mobilities in the order of 10-8 and 10-6 cm2/Vs, respectively. These characteristics are just preliminary in nature. With the right IL, asphaltene thin films may become a good alternative for a transport layer in organic electronic applications.

Decontamination-Induced Modification of Bioactivity in Essential Oil-Based Plasma Polymer Coatings

Plasma polymer coatings fabricated from Melaleuca alternifolia essential oil and its derivatives have been previously shown to reduce the extent of microbial adhesion on titanium, polymers, and other implantable materials used in dentistry. Previous studies have shown these coatings to maintain their performance under standard operating conditions; however, when used in e.g., a dental implant, these coatings may inadvertently become subject to in situ cleaning treatments, such as those using an atmospheric pressure plasma jet, a promising tool for the effective in situ removal of biofilms from tissues and implant surfaces. Here, we investigated the effect of such an exposure on the antimicrobial performance of the Melaleuca alternifolia polymer coating. It was found that direct exposure of the polymer coating surface to the jet for periods less than 60 s was sufficient to induce changes in its surface chemistry and topography, affecting its ability to retard subsequent microbial attachment. The exact effect of the jet exposure depended on the chemistry of the polymer coating, the length of plasma treatment, cell type, and incubation conditions. The change in the antimicrobial activity for polymer coatings fabricated at powers of 20–30 W was not statistically significant due to their limited baseline bioactivity. Interestingly, the bioactivity of polymer coatings fabricated at 10 and 15 W against Staphylococcus aureus cells was temporarily improved after the treatment, which could be attributed to the generation of loosely attached bioactive fragments on the treated surface, resulting in an increase in the dose of the bioactive agents being eluted by the surface. Attachment and proliferation of Pseudomonas aeruginosa cells and mixed cultures were less affected by changes in the bioactivity profile of the surface. The sensitivity of the cells to the change imparted by the jet treatment was also found to be dependent on their origin culture, with mature biofilm-derived P. aeruginosa bacterial cells showing a greater ability to colonize the surface when compared to its planktonic broth-grown counterpart. The presence of plasma-generated reactive oxygen and nitrogen species in the culture media was also found to enhance the bioactivity of polymer coatings fabricated at power levels of 10 and 15 W, due to a synergistic effect arising from simultaneous exposure of cells to reactive oxygen and nitrogen species (RONS) and eluted bioactive fragments. These results suggest that it is important to consider the possible implications of inadvertent changes in the properties and performance of plasma polymer coatings as a result of exposure to in situ decontamination, to both prevent suboptimal performance and to exploit possible synergies that may arise for some polymer coating-surface treatment combinations.

Comparative Study of Natural Terpenoid Precursors in Reactive Plasmas for Thin Film Deposition

If plasma polymer thin films are to be synthesised from sustainable and natural precursors of chemically heterogeneous composition, it is important to understand the extent to which this composition influences the mechanism of polymerisation. To this end, a well-studied monoterpene alcohol, terpinen-4-ol, has been targeted for a comparative study with the naturally occurring mix of terpenes (viz. Melaleuca alternifolia oil) from which it is commonly distilled. Positive ion mode mass spectra of both terpinen-4-ol and M. alternifolia oil showed a decrease in disparities between the type and abundance of cationic species formed in their respective plasma environments as applied plasma power was increased. Supplementary biological assay revealed the antibacterial action of both terpinen-4-ol and M. alternifolia derived coatings with respect to S. aureus bacteria, whilst cytocompatibility was demonstrated by comparable eukaryotic cell adhesion to both coatings. Elucidating the processes occurring within the reactive plasmas can enhance the economics of plasma polymer deposition by permitting use of the minimum power, time and precursor pre-processing required to control the extent of monomer fragmentation and fabricate a film of the desired thickness and functionality.

Plasma and Polymers: Recent Progress and Trends

Plasma-enhanced synthesis and modification of polymers is a field that continues to expand and become increasingly more sophisticated. The highly reactive processing environments afforded by the inherently dynamic nature of plasma media are often superior to ambient or thermal environments, offering substantial advantages over other processing methods. The fluxes of energy and matter toward the surface enable rapid and efficient processing, whereas the charged nature of plasma-generated particles provides a means for their control. The range of materials that can be treated by plasmas is incredibly broad, spanning pure polymers, polymer-metal, polymer-wood, polymer-nanocarbon composites, and others. In this review, we briefly outline some of the recent examples of the state-of-the-art in the plasma-based polymer treatment and functionalization techniques.

In-Situ Surface Modification of Terpinen-4-ol Plasma Polymers for Increased Antibacterial Activity

Surface modification of thin films is often performed to enhance their properties. In this work, in situ modification of Terpinen-4-ol (T4) plasma polymer is carried out via simultaneous surface functionalization and nanoparticle immobilization. Terpinen-4-ol plasma polymers surface were decorated with a layer of ZnO nanoparticles in an oxygen plasma environment immediately after polymer deposition. A combination of hydrophilic modification and ZnO nanoparticle functionalization of the T4 polymer surface led to an enhancement in antibacterial properties by factor of 3 (from 0.75 to 0.25 CFU.mm-2). In addition, ZnO nanoparticle-modified coatings demonstrated improved UV absorbing characteristics in the region of 300-400 nm by 60% relative to unmodified coatings. The ZnO modified coatings were transparent in the visible region of 400-700 nm. The finding points towards the potential use of ZnO nanoparticle-modified T4 plasma polymers as optically transparent UV absorbing coatings.

Antibacterial Nanocomposites Based on Thermosetting Polymers Derived from Vegetable Oils and Metal Oxide Nanoparticles

Thermosetting polymers derived from vegetable oils (VOs) exhibit a wide range of outstanding properties that make them suitable for coatings, paints, adhesives, food packaging, and other industrial appliances. In addition, some of them show remarkable antimicrobial activity. Nonetheless, the antibacterial properties of these materials can be significantly improved via incorporation of very small amounts of metal oxide nanoparticles (MO-NPs) such as TiO2, ZnO, CuO, or Fe3O4. The antimicrobial efficiency of these NPs correlates with their structural properties like size, shape, and mainly on their concentration and degree of functionalization. Owing to their nanoscale dimensions, high specific surface area and tailorable surface chemistry, MO-NPs can discriminate bacterial cells from mammalian ones, offering long-term antibacterial action. MO-NPs provoke bacterial toxicity through generation of reactive oxygen species (ROS) that can target physical structures, metabolic paths, as well as DNA synthesis, thereby leading to cell decease. Furthermore, other modes of action-including lipid peroxidation, cell membrane lysis, redox reactions at the NP-cell interface, bacterial phagocytosis, etc.-have been reported. In this work, a brief description of current literature on the antimicrobial effect of VO-based thermosetting polymers incorporating MO-NPs is provided. Specifically, the preparation of the nanocomposites, their morphology, and antibacterial properties are comparatively discussed. A critical analysis of the current state-of-art on these nanomaterials improves our understanding to overcome antibiotic resistance and offers alternatives to struggle bacterial infections in public places.

Electrically Insulating Plasma Polymer/ZnO Composite Films

In this report, the electrical properties of plasma polymer films functionalized with ZnO nanoparticles were investigated with respect to their potential applications in biomaterials and microelectronics fields. The nanocomposite films were produced using a single-step method that combines simultaneous plasma polymerization of renewable geranium essential oil with thermal decomposition of zinc acetylacetonate Zn(acac)2. The input power used for the deposition of composites were 10 W and 50 W, and the resulting composite structures were abbreviated as Zn/Ge 10 W and Zn/Ge 50 W, respectively. The electrical properties of pristine polymers and Zn/polymer composite films were studied in metal-insulator-metal structures. At a quantity of ZnO of around ~1%, it was found that ZnO had a small influence on the capacitance and dielectric constants of thus-fabricated films. The dielectric constant of films with smaller-sized nanoparticles exhibited the highest value, whereas, with the increase in ZnO particle size, the dielectric constant decreases. The conductivity of the composites was calculated to be in the in the range of 10-14-10-15 Ω-1 m-1, significantly greater than that for the pristine polymer, the latter estimated to be in the range of 10-16-10-17 Ω-1 m-1.

A status review of terpenes and their separation methods

Terpenes or terpenoids are extracted or steam distilled for the recovery of the essential oils of specific fragrant plants. These steam distillates are used to create fine perfumes, to refine the flavor and the aroma of food and drinks, and to produce medicines from plants (phytopharmaca). In recent years, consumers have developed an increasing interest in natural products, as most of these terpenoids have been identified as high value chemicals in food, cosmetic, pharmaceutical, biotechnology, and industrial crops. Extensive chemical techniques and biological tests have led to the identification, biological characterization, and extraction of major components that are of wide interest, especially to the cosmetic and industrial recovery of selective terpenes. The current status of the knowledge of their general structure, functions, and bioactive properties and the methods for their separation are covered in this review.

Eco-friendly nanocomposites derived from geranium oil and zinc oxide in one step approach

Nanocomposites offer attractive and cost-effective thin layers with superior properties for antimicrobial, drug delivery and microelectronic applications. This work reports single-step plasma-enabled synthesis of polymer/zinc nanocomposite thin films via co-deposition of renewable geranium essential oil-derived polymer and zinc nanoparticles produced by thermal decomposition of zinc acetylacetonate. The chemical composition, surfaces characteristics and antimicrobial performance of the designed nanocomposite were systematically investigated. XPS survey proved the presence of ZnO in the matrix of formed polymers at 10 W and 50 W. SEM images verified that the average size of a ZnO nanoparticle slightly increased with an increase in the power of deposition, from approximately 60 nm at 10 W to approximately 80 nm at 50 W. Confocal scanning laser microscopy images showed that viability of S. aureus and E.coli cells significantly reduced on surfaces of ZnO/polymer composites compared to pristine polymers. SEM observations further demonstrated that bacterial cells incubated on Zn/Ge 10 W and Zn/Ge 50 W had deteriorated cell walls, compared to pristine polymers and glass control. The release of ZnO nanoparticles from the composite thin films was confirmed using ICP measurements, and can be further controlled by coating the film with a thin polymeric layer. These eco-friendly nanocomposite films could be employed as encapsulation coatings to protect relevant surfaces of medical devices from microbial adhesion and colonization.

Plant Secondary Metabolite-Derived Polymers: A Potential Approach to Develop Antimicrobial Films

The persistent issue of bacterial and fungal colonization of artificial implantable materials and the decreasing efficacy of conventional systemic antibiotics used to treat implant-associated infections has led to the development of a wide range of antifouling and antibacterial strategies. This article reviews one such strategy where inherently biologically active renewable resources, i.e., plant secondary metabolites (PSMs) and their naturally occurring combinations (i.e., essential oils) are used for surface functionalization and synthesis of polymer thin films. With a distinct mode of antibacterial activity, broad spectrum of action, and diversity of available chemistries, plant secondary metabolites present an attractive alternative to conventional antibiotics. However, their conversion from liquid to solid phase without a significant loss of activity is not trivial. Using selected examples, this article shows how plasma techniques provide a sufficiently flexible and chemically reactive environment to enable the synthesis of biologically-active polymer coatings from volatile renewable resources.

Retention of Antibacterial Activity in Geranium Plasma Polymer Thin Films

Bacterial colonisation of biomedical devices demands novel antibacterial coatings. Plasma-enabled treatment is an established technique for selective modification of physicochemical characteristics of the surface and deposition of polymer thin films. We investigated the retention of inherent antibacterial activity in geranium based plasma polymer thin films. Attachment and biofilm formation by Staphylococcus aureus, Pseudomonas aeruginosa, and Escherichia coli was significantly reduced on the surfaces of samples fabricated at 10 W radio frequency (RF) power, compared to that of control or films fabricated at higher input power. This was attributed to lower contact angle and retention of original chemical functionality in the polymer films fabricated under low input power conditions. The topography of all surfaces was uniform and smooth, with surface roughness of 0.18 and 0.69 nm for films fabricated at 10 W and 100 W, respectively. Hardness and elastic modules of films increased with input power. Independent of input power, films were optically transparent within the visible wavelength range, with the main absorption at ~290 nm and optical band gap of ~3.6 eV. These results suggest that geranium extract-derived polymers may potentially be used as antibacterial coatings for contact lenses.

Photostability of plasma polymerized γ-terpinene thin films for encapsulation of OPV

Optically transparent, smooth, defect-free, chemically inert and with good adhesion to a variety of substrates, plasma polymers from plant-derived secondary metabolites have been identified as promising encapsulating materials for organic electronics and photovoltaics. Here, we demonstrate that an encapsulating layer of plasma polymerized γ-terpinene reduces degradation-related loss in conversion efficiency in PCPDTBT:PC₇₀BM solar cells under ambient operating conditions. The stability of γ-terpinene films was then investigated under extreme UV irradiation conditions as a function of deposition power. When exposed to ambient air, prolonged exposure to UV–A and UV–B light led to notable ageing of the polymer. Photooxidation was identified as the main mechanism of degradation, confirmed by significantly slower ageing when oxygen was restricted through the use of a quartz cover. Under unnatural high-energy UV–C irradiation, significant photochemical degradation and oxidation occurred even in an oxygen-poor environment.

Plant-derived cis-β-ocimene as a precursor for biocompatible, transparent, thermally-stable dielectric and encapsulating layers for organic electronics

This article presents low-temperature, one-step dry synthesis of optically transparent thermally-stable, biocompatible cis-β-ocimene-based thin films for applications as interlayer dielectric and encapsulating layer for flexible electronic devices, e.g. OLEDs. Morphological analysis of thin films shows uniform, very smooth (R_q < 1 nm) and defect-free moderately hydrophilic surfaces. The films are optically transparent, with a refractive index of ~1.58 at 600 nm, an optical band gap of ~2.85 eV, and dielectric constant of 3.5-3.6 at 1 kHz. Upon heating, thin films are chemically and optically stable up to at least 200 °C, where thermal stability increases for films manufactured at higher RF power as well as for films deposited away from the plasma glow. Heating of the sample increases the dielectric constant, from 3.7 (25 °C) to 4.7 (120 °C) at 1 kHz for polymer fabricated at 25 W. Polymers are biocompatible with non-adherent THP-1 cells and adherent mouse macrophage cells, including LPS-stimulated macrophages, and maintain their material properties after 48 h of immersion into simulated body fluid. The versatile nature of the films fabricated in this study may be exploited in next-generation consumer electronics and energy technologies.

Non-equilibrium plasma prevention of Schistosoma japonicum transmission

Schistosoma japonicum is a widespread human and animal parasite that causes intestinal and hepatosplenic schistosomiasis linked to colon, liver and bladder cancers, and anemia. Estimated 230 million people are currently infected with Schistosoma spp, with 779 million people at risk of contracting the parasite. Infection occurs when a host comes into contact with cercariae, a planktonic larval stage of the parasite, and can be prevented by inactivating the larvae, commonly by chemical treatment. We investigated the use of physical non-equilibrium plasma generated at atmospheric pressure using custom-made dielectric barrier discharge reactor to kill S. japonicum cercariae. Survival rate decreased with treatment time and applied power. Plasmas generated in O₂ and air gas discharges were more effective in killing S. japonicum cercariae than that generated in He, which is directly related to the mechanism by which cercariae are inactivated. Reactive oxygen species, such as O atoms, abundant in O₂ plasma and NO in air plasma play a major role in killing of S. japonicum cercariae via oxidation mechanisms. Similar level of efficacy is also shown for a gliding arc discharge plasma jet generated in ambient air, a system that may be more appropriate for scale-up and integration into existing water treatment processes.

Atomic force microscopy enabled roughness analysis of nanostructured poly (diaminonaphthalene) doped poly (vinyl alcohol) conducting polymer thin films

The Atomic Force Microscopy (AFM) helps in evaluating parameters like amplitude or height parameters, functional or statistical parameters and spatial parameters which describe the surface topography or the roughness. In this paper, we have evaluated the roughness parameters for the native poly (vinyl alcohol) (PVA), monomer diaminonaphthalene (DAN) doped PVA, and poly (diaminonaphthalene) (PDAN) doped PVA films prepared in different solvents. In addition, distribution of heights, skewness and Kurtosis moments which describe surface asymmetry and flatness properties of a film were also determined. At the same time line profiles, 3D and 2D images of the surface structures at different scanning areas i.e. 5×5μm² and 10×10μm² were also investigated. From the roughness analysis and the surface skewness and coefficient of Kurtosis parameters, it was concluded that for PVA film the surface contains more peaks than valleys and the PDAN doped PVA film has more valleys than peaks. It was also found that the PDAN doped PVA film with acetonitrile solvent was used for substrate in electronics applications because the film gives less fractal morphology. Thus, the AFM analysis with different parameters suggested that the PDAN doped PVA films are smooth at the sub-nanometer scale.

Emerging Antibacterial Coated Dental Implants: A Preventive Measure for Peri-implantitis

Dental implants are the modern marvel and are widely accepted as a reconstructive treatment modality for tooth replacement.

In recent times, there has been a marked progress in the clinical success rates of dental implants, but implant failures as a result of infections are continuing at an alarming rate of 8% per year, translating into 1 million failures worldwide.

Perimucositis and peri-implantitis are the chief complications reported postimplant surgery that effects its short- and long-term success. Peri-implantitis is characterized by clinical and radiological bone loss around the implant accompanied with an inflammatory reaction of the peri-implant mucosa and is an irreversible condition, whereas perimucositis is a reversible inflammatory change.

Implant surfaces provide an ideal substrate for bacterial adhesion forming a biofilm. Biofilm performs vast functions ranging from physical defensive barrier against phagocytic predation to working as a selective permeable barrier. This limits the diffusion of systemic antimicrobial agents that are capable of damaging the bacterial complexes. These rapidly growing bacteria give rise to a chronic infection which is difficult to eradicate by conventional antibiotic therapy.

To inhibit peri-implant infections, various functional modifications in the implant surfaces have been suggested. The coatings on the titanium implant are incorporated with disinfectants, antibiotics as well as antimicrobial peptides AMPs.

This paper is an attempt to review all the antibiotic coatings available for a titanium implant and discuss their prospective future to prevent peri-implant infections.

How to cite this article

Yarramaneni V, Aparna IN, Sachdeva A, Balakrishnan D, Prabhu N. Emerging Antibacterial Coated Dental Implants: A Preventive Measure for Peri-implantitis. World J Dent 2016;7(4):195-198.

UV-cured thiol–ene eugenol/ZnO composite materials with antibacterial properties

ZnO nanoparticles, i.e. efficient antimicrobial inorganic compounds, are combined to eugenol-based networks to design by “click chemistry” new promising eugenol/ZnO composite with enhanced antibacterial properties for biomedical applications.

Sustainable Life Cycles of Natural-Precursor-Derived Nanocarbons

Sustainable societal and economic development relies on novel nanotechnologies that offer maximum efficiency at minimal environmental cost. Yet, it is very challenging to apply green chemistry approaches across the entire life cycle of nanotech products, from design and nanomaterial synthesis to utilization and disposal. Recently, novel, efficient methods based on nonequilibrium reactive plasma chemistries that minimize the process steps and dramatically reduce the use of expensive and hazardous reagents have been applied to low-cost natural and waste sources to produce value-added nanomaterials with a wide range of applications. This review discusses the distinctive effects of nonequilibrium reactive chemistries and how these effects can aid and advance the integration of sustainable chemistry into each stage of nanotech product life. Examples of the use of enabling plasma-based technologies in sustainable production and degradation of nanotech products are discussed-from selection of precursors derived from natural resources and their conversion into functional building units, to methods for green synthesis of useful naturally degradable carbon-based nanomaterials, to device operation and eventual disintegration into naturally degradable yet potentially reusable byproducts.

Anti-bacterial surfaces: natural agents, mechanisms of action, and plasma surface modification

This article reviews antibacterial surface strategies based on reactive plasma chemistry, focusing on how plasma-assisted processing of natural antimicrobial agents can produce antifouling and antibacterial materials for biomedical devices.

Microtopography of the eye surface of the crab Carcinus maenas: an atomic force microscope study suggesting a possible antifouling potential

Marine biofouling causes problems for technologies based on the sea, including ships, power plants and marine sensors. Several antifouling techniques have been applied to marine sensors, but most of these methodologies are environmentally unfriendly or ineffective. Bioinspiration, seeking guidance from natural solutions, is a promising approach to antifouling. Here, the eye of the green crab Carcinus maenas was regarded as a marine sensor model and its surface characterized by means of atomic force microscopy. Engineered surface micro- and nanotopography is a new mechanism found to limit biofouling, promising an effective solution with much reduced environmental impact. Besides giving a new insight into the morphology of C. maenas eye and its characterization, our study indicates that the eye surface probably has antifouling/fouling-release potential. Furthermore, the topographical features of the surface may influence the wettability properties of the structure and its interaction with organic molecules. Results indicate that the eye surface micro- and nanotopography may lead to bioinspired solutions to antifouling protection.

Enrichment of previously uncultured bacteria from natural complex communities by adhesion to solid surfaces

The adhesion to inert solid surfaces was explored as a novel approach for the enrichment of previously uncultured bacteria from natural microbial communities. Enrichments on solid steel, glass and synthetic polymeric surfaces were established using samples from five freshwater lakes, a marine microbial mat and an alpine soil, and were subsequently analysed by molecular fingerprinting and sequencing of their 16S rRNA gene fragments. The majority of the enriched phylotypes grouped with the Alphaproteobacteria, Betaproteobacteria or Bacteroidetes and in several cases were related to typical biofilm-forming species and genera. Most enrichments were most closely related to previously uncultured phylotypes and none had previously been cultivated from the original environments even when applying improved high throughput liquid cultivation techniques. Of the 13 phylotypes enriched from freshwater samples, seven were previously unknown, three matched so-far uncultured environmental clones, and three were identical to previously cultivated bacteria. Of the 17 phylotypes recovered from soil, 12 were previously unknown with five of these phylotypes representing novel genera, whereas five phylotypes were identical to previously cultured soil bacteria. The feasibility of the biofilm-enrichment approach was exemplified by the successful isolation of a not-yet cultured Betaproteobacterium that constituted a discernible component of the alpine soil microbial community in situ and exhibited only 93% similarity to its closest cultured relative. Based on these results, cultivation on solid surfaces represents a promising approach to recover isolates that have so far escaped cultivation as suspended cultures in liquid media.