Synthesis and Characterization of Bi2WxMo1−xO6 Solid Solutions and Their Application in Photocatalytic Desulfurization under Visible Light

Synthesis and Characterization of Fe Doped Aurivillius-Phase PbBi2Nb2O9 Perovskite and Their Photocatalytic Activity on the Degradation of Methylene Blue

A simple solid-state reaction was applied to synthesize Fe-doped perovskite-type PBFNO catalysts, and methylene blue decomposition studies were performed in the form of visible light according to the changes in the Fe doping content (0.4 to 1.9 mol ratio compared with Bi mol) and the amount of catalyst used (0.05 to 0.2 g used). As the Fe doping content increases, the absorbance and bang gap energy of the PBFNOs sample rapidly increase and decrease, respectively, because the Fe dopant in the PBNO lattice acts as an intermediate band between the valence and conduction bands of the PBNO and reduces the band gap energy. As a result, it showed a performance degradation of approximately 42% compared to the maximum performance. In addition, the presence of Fe dopants in the PBNO lattice greatly reduces the intensity of the photoluminescent lines. This is because the Fe dopant can play an important role in light-induced electron transfer and as a hole trap, reducing the recombination rate. Additionally, when too much photocatalyst was used (>0.1 g used), the Fe dopant played an important role as a light-induced electron transfer and hole trap, reducing the recombination rate and lowering the overall photocatalytic activity by 51%. In particular, 0.1 g of PBNO-0.2-F showed continuous catalytic activity, even when the photocatalytic reaction proceeded for 180 min. Therefore, this study demonstrates that the Fe-doped aurivillius-phase PBFNO photocatalyst is very promising for the dye manufacturing industry.

Degradation of Dye Wastewater by a Novel mBT-MPR Visible Light Photocatalytic System

The high efficiency and low consumption green wastewater treatment technology has important practical significance for the recycling of printing and dyeing wastewater. The efficiency of visible light catalytic degradation of organics is greatly affected by the performance of the catalyst and the photo reactor. Therefore, Bi₂WO₆/TiO₂/Fe₃O₄ (mBT) visible light photocatalyst was accurately prepared by the ammonia iron double drop method. In order to improve the photodegradation efficiency, a tubular magnetic field-controlled photocatalytic reactor (MPR) was developed. The novel mBT-MPR visible light photocatalytic system was proposed to treat RhB simulated wastewater. The experimental results showed that when the dosage of mBT catalyst was 1 g/L and visible light was irradiated for 60 min, the average removal rate of rhodamine B (RhB) with initial an concentration of 10 mg/L in the simulated wastewater for four times was 91.7%. The mBT-MPR visible light photocatalysis system is a green and efficient treatment technology for organic pollutants in water with simple operation, low energy consumption, and no need for catalyst separation.

Towards the Sustainable Production of Ultra-Low-Sulfur Fuels through Photocatalytic Oxidation

Nowadays, the sulfur-containing compounds are removed from motor fuels through the traditional hydrodesulfurization technology, which takes place under harsh reaction conditions (temperature of 350–450 °C and pressure of 30–60 atm) in the presence of catalysts based on alumina with impregnated cobalt and molybdenum. According to the principles of green chemistry, energy requirements should be recognized for their environmental and economic impacts and should be minimized, i.e., the chemical processes should be carried out at ambient temperature and atmospheric pressure. This approach could be implemented using photocatalysts that are sensitive to visible light. The creation of highly active photocatalytic systems for the deep purification of fuels from sulfur compounds becomes an important task of modern catalysis science. The present critical review reports recent progress over the last 5 years in heterogeneous photocatalytic desulfurization under visible light irradiation. Specific attention is paid to the methods for boosting the photocatalytic activity of materials, with a focus on the creation of heterojunctions as the most promising approach. This review also discusses the influence of operating parameters (nature of oxidant, molar ratio of oxidant/sulfur-containing compounds, photocatalyst loading, etc.) on the reaction efficiency. Some perspectives and future research directions on photocatalytic desulfurization are also provided.