1
|
Abstract
This study conducted a radial flow experiment to investigate the existence of non-Darcy flow and calculate the non-Darcy “inertia” coefficient; the experiment was performed on seven cylindrical perforated artificial porous media samples. Two hundred thirty-one runs were performed, and the pressure drop was reported. The non-Darcy coefficient β was calculated and compared with available in the literature. The results showed that the non-Darcy coefficient decreased nonlinearly and converged on a value within a specific range as the permeability increased. Nonetheless, it was found that the non-Darcy flow exists even in the very low flow rate deployed in this study. In addition, it has been found that the non-Darcy effect is not due to turbulence but also the inertial effect. The existence of a non-Darcy flow was confirmed for all the investigated samples. The Forchheimer numbers for airflow at varied flow rates are determined using experimentally measured superficial velocity, permeability, and non-Darcy coefficient.
Collapse
|
2
|
Surrogate Models for Studying the Wettability of Nanoscale Natural Rough Surfaces Using Molecular Dynamics. ENERGIES 2020. [DOI: 10.3390/en13112770] [Citation(s) in RCA: 10] [Impact Index Per Article: 2.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 12/11/2022]
Abstract
A molecular modeling methodology is presented to analyze the wetting behavior of natural surfaces exhibiting roughness at the nanoscale. Using atomic force microscopy, the surface topology of a Ketton carbonate is measured with a nanometer resolution, and a mapped model is constructed with the aid of coarse-grained beads. A surrogate model is presented in which surfaces are represented by two-dimensional sinusoidal functions defined by both an amplitude and a wavelength. The wetting of the reconstructed surface by a fluid, obtained through equilibrium molecular dynamics simulations, is compared to that observed by the different realizations of the surrogate model. A least-squares fitting method is implemented to identify the apparent static contact angle, and the droplet curvature, relative to the effective plane of the solid surface. The apparent contact angle and curvature of the droplet are then used as wetting metrics. The nanoscale contact angle is seen to vary significantly with the surface roughness. In the particular case studied, a variation of over 65° is observed between the contact angle on a flat surface and on a highly spiked (Cassie–Baxter) limit. This work proposes a strategy for systematically studying the influence of nanoscale topography and, eventually, chemical heterogeneity on the wettability of surfaces.
Collapse
|
3
|
Experimental Study on the Effect of ASP Flooding on Improving Oil Recovery in Low Permeability Reservoirs Based on a Partial Quality Tool. Processes (Basel) 2020. [DOI: 10.3390/pr8030296] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/16/2022] Open
Abstract
In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. In the formation, the partial quality tool degrades the polymer through active shearing action, reducing the molecular weight of the polymer, to improve the matching degree to the low permeability oil layer and the oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.
Collapse
|