Application and Mechanism of Sludge-Based Activated Carbon for Phenol and Cyanide Removal from Bio-Treated Effluent of Coking Wastewater

Highly Efficient Separation of Ethanol Amines and Cyanides via Ionic Magnetic Mesoporous Nanomaterials

Simple and efficient sample pretreatment methods are important for analysis and detection of chemical warfare agents (CWAs) in environmental and biological samples. Despite many commercial materials or reagents that have been already applied in sample preparation, such as SPE columns, few materials with specificity have been utilized for purification or enrichment. In this study, ionic magnetic mesoporous nanomaterials such as poly(4-VB)@M-MSNs (magnetic mesoporous silicon nanoparticles modified by 4-vinyl benzene sulfonic acid) and Co2+@M-MSNs (magnetic mesoporous silicon nanoparticles modified by cobalt ions) with high absorptivity for ethanol amines (EAs, nitrogen mustard degradation products) and cyanide were successfully synthesized. The special nanomaterials were obtained by modification of magnetic mesoporous particles prepared based on co-precipitation using -SO3H and Co2+. The materials were fully characterized in terms of their composition and structure. The results indicated that poly(4-VB)@M-MSNs or Co2+@M-MSNs had an unambiguous core-shell structure with a BET of 341.7 m2·g-1 and a saturation magnetization intensity of 60.66 emu·g-1 which indicated the good thermal stability. Poly(4-VB)@M-MSNs showed selective adsorption for EAs while the Co2+@M-MSNs were for cyanide, respectively. The adsorption capacity quickly reached the adsorption equilibrium within the 90 s. The saturated adsorption amounts were MDEA = 35.83 mg·g-1, EDEA = 35.00 mg·g-1, TEA = 17.90 mg·g-1 and CN-= 31.48 mg·g-1, respectively. Meanwhile, the adsorption capacities could be maintained at 50-70% after three adsorption-desorption cycles. The adsorption isotherms were confirmed as the Langmuir equation and the Freundlich equation, respectively, and the adsorption mechanism was determined by DFT calculation. The adsorbents were applied for enrichment of targets in actual samples, which showed great potential for the verification of chemical weapons and the destruction of toxic chemicals.

Further treatment of coking wastewater treated in A2O-MBR by the nanofiltration-powder activated carbon hybrid system

In this study, further treatment of coking wastewater treated in anoxic-oxic-membrane bioreactor (A2O-MBR) was investigated to meet the standards of the ministry by means of nanofiltration (NF) (with two different membranes and different pressures), microfiltration -powder activated carbon (MF-PAC) hybrid system and NF-PAC (with two different membranes and five different PAC concentrations) hybrid system. In addition to the parameters determined by the ministry, other parameters such as ammonium, thiocyanate (SCN-), hydrogen cyanide (HCN), dissolved organic carbon (DOC), dissolved inorganic carbon (DIC), color were also examined to evaluate the flux performance and treatment efficiency of the hybrid processes. According to the results, chemical oxygen demand (COD) in the NF process, COD and total cyanide (T-CN) in the MF-PAC process could not meet the discharge standards. As for the NF-PAC hybrid system, XN45 membrane met the discharge standards in all parameters (COD = 96±1.88 mg/L, T-CN =<0,02 mg/L, phenol =<0.05 mg/L), with a recovery rate of 78% at 0.5 g/L PAC concentration.

Formation of self-nitrogen-doping activated carbon from Fish/sawdust/ZnCl2 by hydrothermal and pyrolysis for toxic chromium adsorption from wastewater

This study gives a description of the formation of self-nitrogen doped activated carbon (NDAC) by a novel way of employing fish meal (mixture of Atherina hepseetus and Sardina pilchardus of 60% protein) as nitrogen dopant, ZnCl₂ as impregnate agent, sawdust as carbon source and water with a mass ratio (2:1:1:12), which subjected to the hydrothermal process. The hydrothermal mixture was oven dried and carbonized under a flow of nitrogen for one h at 600, 700, and 800 °C. The characterization of NDAC was performed by using various analytical techniques analyses. The synthesized NDAC exhibited unique features such as microporous structure (1.84 ~ 2.01 nm), high surface area (437.51 ~ 680.86 m²/g), the volume of total pores (0.22 ~ 0.32 cm³/g) and nitrogen content (12.82 ~ 13.73%). Batch removal tests were achieved to investigate the impact of chromium ions starting concentration (100-400 mg/L), NDAC dose (0.5-2.5 g/L), pH and contact time (5-120 min). Such helpful characteristics of NDAC, particularly for NDAC600, were suitable to use as an excellent adsorbent for Cr⁶⁺ ions with a maximum adsorption capacity (Q_m) (769.23 mg/g), and the highest chromium ions adsorption uptake (81.18%) was obtained at pH value 1.5 at room temperature. Both Halsey and Temkin models fitted the adsorption data quite reasonably. The uptake of toxic chromium ions is best represented with pseudo-second-order rate kinetics data.

Urban mining from biomass, brine, sewage sludge, phosphogypsum and e-waste for reducing the environmental pollution: Current status of availability, potential, and technologies with a focus on LCA and TEA

Rapid industrialization, improved standards of living, growing economies and ever-increasing population has led to the unprecedented exploitation of the finite and non-renewable resources of minerals in past years. It was observed that out of 100 BMT of raw materials processed annually only 10% is recycled back. This has resulted in a strenuous burden on natural or primary resources of minerals (such as ores) having limited availability. Moreover, severe environmental concerns have been raised by the huge piles of waste generated at landfill sites. To resolve these issues, 'Urban Mining' from waste or secondary resources in a Circular Economy' concept is the only sustainable solution. The objective of this review is to critically examine the availability, elemental composition, and the market potential of the selected secondary resources such as lignocellulosic/algal biomass, desalination water, sewage sludge, phosphogypsum, and e-waste for minerals sequestration. This review showed that, secondary resources have potential to partially replace the minerals required in different sectors such as macro and microelements in agriculture, rare earth elements (REEs) in electrical and electronics industry, metals in manufacturing sector and precious elements such as gold and platinum in ornamental industry. Further, inputs from the selected life cycle analysis (LCA) & techno economic analysis (TEA) were discussed which showed that although, urban mining has a potential to reduce the greenhouse gaseous (GHG) emissions in a sustainable manner however, process improvements through innovative, novel and cost-effective pathways are essentially required for its large-scale deployment at industrial scale in future.

Identifying the critical activated carbon properties affecting the adsorption of effluent organic matter from bio-treated coking wastewater

Activated carbon is widely used to remove effluent organic matter (EfOM) from bio-treated coking wastewater. However, the critical carbon properties affecting adsorption performance are still unclear. Nine commercial powdered activated carbons (PACs) with different pore structures, surface functional groups, and surface charges were used to adsorb EfOM from bio-treated coking wastewater, which was fractionated according to their molecular weight (MW) and hydrophobicity. Good correlations were observed between the adsorption of biopolymers (MW > 20,000 Da, 7 %) and macropore volume (>50 nm), as well as between the adsorption of humics (MW = 1000 ~ Da, 36 %) and mesopore volume (2-50 nm), suggesting that the adsorption sites of EfOM depended on their molecular size. Higher isoelectric points and fewer acidic groups promoted the adsorption of the most negatively charged hydrophobic acids (HPOA, 39.5 %). According to variation partitioning analysis (VPA), mesopore-macropore greatly contributed to the adsorption capacities of EfOM (71.3 %), whereas the sum of phenolic hydroxyl and carboxyl (26.3 %) and isoelectric point (12.2 %) affected the normalized adsorption capacities of EfOM. In conclusion, PAC with a higher mesopore volume, fewer acidic groups, and a higher isoelectric point was desirable for removing EfOM from bio-treated coking wastewater. This study provides guidance for the selection of PAC for the removal of EfOM from bio-treated coking wastewater.

Fabrication of N-doping activated carbons from fish waste and sawdust for Acid Yellow 36 dye removal from an aquatic environment

Acid Yellow 36 (AY36) dye is a synthetic azo dye that is excessively used in various industries, causing hazardous environmental effects. The main target of this study is the preparation of self-N-doped porous activated carbon (NDAC) and the investigation in eliminating the AY36 dye from the water solution. The NDAC was prepared by mixing fish waste (60% protein content) which was considered a self-nitrogen dopant. A combination of Fish waste, sawdust, zinc chloride and urea with a mass ratio (5:5:5:1) was submitted to hydrothermal process at 180 °C for 5 h followed by pyrolysis for 1 h under N₂ stream at 600, 700, and 800 °C. Fabricated NDAC was qualified as an adsorbent for recovering AY36 dye from water using batch trials. The fabricated NDAC samples were characterized by FTIR, TGA, DTA, BET, BJH, MP, t-plot, SEM, EDX, and XRD methods. The results showed the successful formation of NDAC with nitrogen mass percentage content (4.21, 8.13 and 9.85%). The NDAC prepared at 800 °C had the largest nitrogen content (9.85%) and was labeled as NDAC800. This later had 727.34 m²/g, 167.11 cm³/g, and 1.97 nm for specific surface area, the monolayer volume and the mean pores diameter respectively. By being the more efficient adsorbent, NDAC800 was chosen to test AY36 dye removal. Therefore, it is selected to investigate the removal of AY36 dye from aqueous solution by varying important parameters such as solution pH, initial dye concentration, adsorbent dosage and contact time. The removal of AY36 dye by NDAC800 was pH-dependent, with the optimum pH value 1.5 giving 85.86% removal efficiency and 232.56 mg/g maximum adsorption capacity (Q_m). The kinetic data exhibited the best fit model with the pseudo-second-order (PSOM), while the equilibrium data fit well with the Langmuir (LIM) and Temkin (TIM). The mechanism of AY36 dye adsorption may be ascribed to the electrostatic contact between the dye and the available charged sites on NDAC800 surface. The prepared NDAC800 may be considered as an efficient, available, and eco-friendly adsorbent for AY36 dye adsorption from simulated water.

Sewage Sludge Derived Materials for CO2 Adsorption

The study tried to contribute to solving two serious environmental issues: CO2 reducing and sewage sludge disposal. Thus, sewage-sludge-derived materials were obtained in order to be evaluated for CO2 adsorption capacity. Therefore, the char resulted after the sewage sludge pyrolysis was subjected to oxidation and chemical activation processes by using different quantities of alkaline hydroxide. One of the obtained materials, activated with a lower quantity of alkaline hydroxide, was also treated with acid chloride. Further, the materials were structural and texturally characterized, and material treated with acid chloride was used for CO2 adsorption tests, due to high surface area and pore volume. The handmade system coupled to a gas chromatograph allowed the adsorption efficiency evaluation using different feed gases (rich and poor in CO2) by completed purge of pipe line and on-line check. Additionally, the adsorption capacity, separation efficiency, and CO2 recovery were calculated. Taking into account the values for adsorption capacity (separation efficiency and CO2 recovery), it can be concluded that the sewage sludge derived material could be a promising solution for CO2 reduction and waste disposal.

Carbonaceous Adsorbents Derived from Agricultural Sources for the Removal of Pramipexole Pharmaceutical Model Compound from Synthetic Aqueous Solutions

The aim of the present study was to synthesize various samples of activated carbon (AC) from different agricultural sources as precursors, like orange peels, tea stalks, and kiwi peels, as well as sucrose. The synthesis of AC was achieved with chemical activation using H3PO4 and KOH. The produced AC samples were tested as adsorbents for the removal of a pharmaceutical model compound, pramipexole dihydrochloride (PRM), from synthetic aqueous synthetic solutions. The produced-from-sucrose AC presented the higher yield of synthesis (~58%). The physicochemical features of the materials were analyzed by FTIR spectroscopy, N2 physisorption, and SEM imaging. More specifically, the AC sample derived from sucrose (SG-AC) had the highest specific surface area (1977 m2/g) with the total pores volume, mesopores volume, and external surface area being 1.382 cm3/g, 0.819 cm3/g, and 751 m2/g, respectively. The effect of the initial pH and PRM concentration were studied, while the equilibrium results (isotherms) were fitted to Langmuir and Freundlich models. The maximum adsorption capacities were found to be 213, 190, 155, and 115 mg/g for AC samples produced from sucrose, kiwi peels, orange peels, and tea stalks, respectively.

Surface Functionalization of Biochar from Oil Palm Empty Fruit Bunch through Hydrothermal Process

The use of biochar as an adsorbent for wastewater treatment purposes has been hindered due to its lower surface area compared to activated carbon. Current research on increasing surface functional groups on biochar surfaces to improve its adsorption performance suggests using high chemical concentration and long period of modification. This study solves these problems by focusing on improving surface functionalities of biochar via the hydrothermal functionalization process. Oil palm empty fruit bunch biochar was functionalized using autoclave with nitric acid as the functionalization agent. Functionalized biochar properties such as Brunauer–Emmett–Teller (BET) surface area and surface functional groups were analyzed and compared with untreated biochar. Fourier Transform Infrared (FTIR) spectroscopic analysis shows a significant increase in absorption by oxygen functional groups and is corroborated with energy dispersive X-ray (EDX) analysis. The process does not result in any major change in surface morphology and reduction in surface area value. Methylene blue (MB) adsorption test shows 7 times increase in adsorption performance. These results show that the simple hydrothermal functionalization process successfully functionalizes the biochar surface and improves its performance without affecting its surface area at lower concentration, and shorter time compared to previous studies. This result, with future large-scale experimentation using real-life equipment in palm oil mills, would provide a better technology that can be implemented in the industry.

Current State of Porous Carbon for Wastewater Treatment

Porous materials constitute an attractive research field due to their high specific surfaces; high chemical stabilities; abundant pores; special electrical, optical, thermal, and mechanical properties; and their often higher reactivities. These materials are currently generating a great deal of enthusiasm, and they have been used in large and diverse applications, such as those relating to sensors and biosensors, catalysis and biocatalysis, separation and purification techniques, acoustic and electrical insulation, transport gas or charged species, drug delivery, and electrochemistry. Porous carbons are an important class of porous materials that have grown rapidly in recent years. They have the advantages of a tunable pore structure, good physical and chemical stability, a variable specific surface, and the possibility of easy functionalization. This gives them new properties and allows them to improve their performance for a given application. This review paper intends to understand how porous carbons involve the removal of pollutants from water, e.g., heavy metal ions, dyes, and organic or inorganic molecules. First, a general overview description of the different precursors and the manufacturing methods of porous carbons is illustrated. The second part is devoted to reporting some applications such using porous carbon materials as an adsorbent. It appears that the use of porous materials at different scales for these applications is very promising for wastewater treatment industries.

Biodegradation of Phenol by Rhodococcus sp. Strain SKC: Characterization and Kinetics Study

This study focuses on the kinetics of a pure strain of bacterium Rhodococcus sp. SKC, isolated from phenol-contaminated soil, for the biodegradation of phenol as its sole carbon and energy source in aqueous medium. The kinetics of phenol biodegradation including the lag phase, the maximum phenol degradation rate, maximum growth rate (R_m) and maximum yield coefficient (Y) for each S_i (initial phenol concentration, mg/L) were fitted using the Gompertz and Haldane models of substrate inhibition (R² > 0.9904, RMSE < 0.00925). The values of these parameters at optimum conditions were μ_max = 0.30 h⁻¹, K_s = 36.40 mg/L, and K_i = 418.79 mg/L, and that means the inhibition concentration of phenol was 418.79 mg/L. By comparing with other strains of bacteria, Rhodococcus sp. SKC exhibited a high yield factor and tolerance towards phenol. This study demonstrates the potential application of Rhodococcus sp. SKC for the bioremediation of phenol contaminate.

Wastewater Treatment Processes: Part I

Cheap and plentiful, water was for centuries a manufacturing tool that industry took for granted [...]

The Potentiality of Rice Husk-Derived Activated Carbon: From Synthesis to Application

Activated carbon (AC) has been extensively utilized as an adsorbent over the past few decades. AC has widespread applications, including the removal of different contaminants from water and wastewater, and it is also being used in capacitors, battery electrodes, catalytic supports, and gas storage materials because of its specific characteristics e.g., high surface area with electrical properties. The production of AC from naturally occurring precursors (e.g., coal, biomass, coconut shell, sugarcane bagasse, and so on) is highly interesting in terms of the material applications in chemistry; however, recently much focus has been placed on the use of agricultural wastes (e.g., rice husk) to produce AC. Rice husk (RH) is an abundant as well as cheap material which can be converted into AC for various applications. Various pollutants such as textile dyes, organic contaminants, inorganic anions, pesticides, and heavy metals can be effectively removed by RH-derived AC. In addition, RH-derived AC has been applied in supercapacitors, electrodes for Li-ion batteries, catalytic support, and energy storage, among other uses. Cost-effective synthesis of AC can be an alternative for AC production. Therefore, this review mainly covers different synthetic routes and applications of AC produced from RH precursors. Different environmental, catalytic, and energy applications have been pinpointed. Furthermore, AC regeneration, desorption, and relevant environmental concerns have also been covered. Future scopes for further research and development activities are also discussed. Overall, it was found that RH-derived AC has great potential for different applications which can be further explored at real scales, i.e., for industrial applications in the future.