Pumpkin seed oil: a comprehensive review of extraction methods, nutritional constituents, and health benefits

Pumpkin seed oil (PSO), a rich source of nutrients, is extracted from the seeds of different pumpkin varieties for food and medicines. This article aims to provide an evidence-based review of the literature and to explore the extraction technologies, nutritional properties, and biological activity of PSO. From previous literature, PSO contains a large proportion of unsaturated fatty acids, with linoleic acid as the main component, and an amount of tocopherol, phytosterol, and phenolic acids. Some differences in the yield, composition, and physicochemical properties of PSO can be associated with the pumpkin's cultivars and the extraction methods. Some novel technologies involved in supercritical fluid extraction, enzyme-assisted aqueous extraction, and ultrasound-assisted extraction have been replacing the conventional technologies gradually as promising methods for the safe, non-polluting, and effective recovery of PSO. This healthy vegetable oil was reported by several in vitro and in vivo studies to have potential protective roles in oxidative stress, inflammation, cancer, and cardiovascular diseases. © 2023 Society of Chemical Industry.

Assessment of Quality and Efficiency of Cold-Pressed Oil from Selected Oilseeds

In this present study, an oil press was used to process 200 g each of sesame, pumpkin, flax, milk thistle, hemp and cumin oilseeds in order to evaluate the amount of oil yield, seedcake, sediments and material losses (oil and sediments). Sesame produced the highest oil yield at 30.60 ± 1.69%, followed by flax (27.73 ± 0.52%), hemp (20.31 ± 0.11%), milk thistle (14.46 ± 0.51%) and pumpkin (13.37 ± 0.35%). Cumin seeds produced the lowest oil yield at 3.46 ± 0.15%. The percentage of sediments in the oil, seedcake and material losses for sesame were 5.15 ± 0.09%, 60.99 ± 0.04% and 3.27 ± 1.56%. Sediments in the oil decreased over longer storage periods, thereby increasing the percentage oil yield. Pumpkin oil had the highest peroxide value at 18.45 ± 0.53 meq O2/kg oil, an acid value of 11.21 ± 0.24 mg KOH/g oil, free fatty acid content of 5.60 ± 0.12 mg KOH/g oil and iodine value of 14.49 ± 0.16 g l/100 g. The univariate ANOVA of the quality parameters against the oilseed type was statistically significant (p-value < 0.05), except for the iodine value, which was not statistically significant (p-value > 0.05). Future studies should analyze the temperature generation, oil recovery efficiency, percentage of residual oil in the seedcake and specific energy consumption of different oilseeds processed using small-large scale presses.

Determination of Maximum Oil Yield, Quality Indicators and Absorbance Spectra of Hulled Sunflower Seeds Oil Extraction under Axial Loading

The present study aims to estimate the maximum oil yield of hulled sunflower seed samples in a uniaxial process under a load of 40 kN and speed of 4 mm/min. The oil samples were assessed for their quality parameters and spectra curves within the wavelength range of 325–600 nm. The results show that heating temperatures in the range of 40 °C to 80 °C increased the oil output; however, a maximum oil yield of 48.869 ± 6.023% with a minimum energy of 533.709 ± 65.644 J at the fifth repeated pressing was obtained from the unheated sample compared to the heated samples. The peroxide values ranged from 6.898 ± 0.144 to 7.290 ± 0.507 meq O₂/kg, acid values from 1.043 ± 0.166 to 1.998 ± 0.276 mg KOH/g oil and free fatty acid values from 0.521 ± 0.083 to 0.999 ± 0.138 mg KOH/g oil, which were within the recommended quality threshold. There were significant spectral differences among the oil samples. A single absorbance peak was observed at 350 nm for all oil samples, indicating low levels of pigment molecules in the oil. The study revealed the need for repeated pressings to recover the considerable residual oil remaining in the seedcake after the first pressing.

Using Box–Behnken Design Coupled with Response Surface Methodology for Optimizing Rapeseed Oil Expression Parameters under Heating and Freezing Conditions

The effect of heating and freezing pretreatments on rapeseed oil yield and the volume of oil energy under uniaxial compression loading was investigated. Four separate experiments were carried out to achieve the study objective. The first and second experiments were performed to determine the compression parameters (deformation, mass of oil, oil yield, oil expression efficiency, energy, volume of oil and volume of oil energy). The third and fourth experiments identified the optimal factors (heating temperatures: 40, 60 and 80 °C, freezing temperatures: −2, −22 and −36 °C, heating times: 15, 30 and 45 min and speeds: 5, 10 and 15 mm/min) using the Box–Behnken design via the response surface methodology where the oil yield and volume of oil energy were the main responses. The optimal operating factors for obtaining a volume of oil energy of 0.0443 kJ/mL were a heating temperature of 40 °C, heating time of 45 min and speed of 15 mm/min. The volume of oil energy of 0.169 kJ/mL was reached at the optimal conditions of a freezing temperature of −36 °C, freezing time of 37.5 min and speed of 15 mm/min. The regression model established was adequate for predicting the volume of oil energy only under heating conditions.

Optimizing Uniaxial Oil Extraction of Bulk Rapeseeds: Spectrophotometric and Chemical Analyses of the Extracted Oil under Pretreatment Temperatures and Heating Intervals

Optimizing the operating factors in edible oil extraction requires a statistical technique such as a response surface methodology for evaluating their effects on the responses. The examined input factors in this study were the diameter of pressing vessel, VD (60, 80, and 100 mm), temperature, TPR (40, 60, and 80 °C), and heating time, HTM (30, 60 and 90 min). The combination of these factors generated 17 experimental runs where the mass of oil, oil yield, oil extraction efficiency, and deformation energy were calculated. Based on the response surface regression analysis, the combination of the optimized factors was VD: 100 (+1) mm; TPR: 80 °C (+1) and HTM: 60 (0) min); VD: 60 (–1) mm; TPR: 80 °C (+1) and HTM: 75 (+0.5) min and VD: 100 (+1) mm; TPR: 80 °C (+1) and HTM: 90 (+1). The absorbance and transmittance values significantly (p < 0.05) correlated with the wavelength and temperature, but they did not correlate significantly (p > 0.05) with heating time. The peroxide value did not correlate significantly with temperature, however, it correlated significantly with heating time. Neither the acid value nor the free fatty acid value correlated with both temperature and heating time. The findings of the present study are part of our continuing research on oilseeds’ processing optimization parameters.