Sensors for highly toxic gases: methylamine and hydrogen chloride detection at low concentrations in an ionic liquid on Pt screen printed electrodes

Fabrication of Tungsten Oxide Nanowalls through HFCVD for Improved Electrochemical Detection of Methylamine

In this study, well-defined tungsten oxide (WO3) nanowall (NW) thin films were synthesized via a controlled hot filament chemical vapor deposition (HFCVD) technique and applied for electrochemical detection of methylamine toxic substances. Herein, for the thin-film growth by HFCVD, the temperature of tungsten (W) wire was held constant at ~1450 °C and gasification was performed by heating of W wire using varied substrate temperatures ranging from 350 °C to 450 °C. At an optimized growth temperature of 400 °C, well-defined and extremely dense WO3 nanowall-like structures were developed on a Si substrate. Structural, crystallographic, and compositional characterizations confirmed that the deposited WO3 thin films possessed monoclinic crystal structures of high crystal quality. For electrochemical sensing applications, WO3 NW thin film was used as an electrode, and cyclic voltammetry (CV) and linear sweep voltammetry (LSV) were measured with a wide concentration range of 20 μM~1 mM of methylamine. The fabricated electrochemical sensor achieved a sensitivity of ~183.65 μA mM-1 cm-2, a limit of detection (LOD) of ~20 μM and a quick response time of 10 s. Thus, the fabricated electrochemical sensor exhibited promising detection of methylamine with considerable stability and reproducibility.

Simultaneous electrochemical detection of glycated and human serum albumin for diabetes management

Developing highly selective and sensitive biosensors for diabetes management blood glucose monitoring is essential to reduce the health risks associated with diabetes. Assessing the glycation (GA) of human serum albumin (HSA) serves as an indicator for medium-term glycemic control, making it suitable for assessing the efficacy of blood glucose management protocols. However, most biosensors are not capable of simultaneous detection of the relative fraction of GA to HSA in a clinically relevant range. Here, we report an effective miniaturised biosensor architecture for simultaneous electrochemical detection of HSA and GA across relevant concentration ranges. We immobilise DNA aptamers specific for the detection of HSA and GA on gold nanoislands (Au NIs) decorated screen-printed carbon electrodes (SPCEs), and effectively passivate the residual surface sites. We achieve a dynamic detection range between 20 and 60 mg/mL for HSA and 1-40 mg/mL for GA in buffer solutions. The analytical utility of our HSA and GA biosensor architectures are validated in mice serum indicating immediate potential for clinical applications. Since HSA and GA have similar structures, we extensively assess our sensor specificity, observing high selectivity of the HSA and GA sensors against each other and other commonly present interfering molecules in blood such as glucose, glycine, ampicillin, and insulin. Additionally, we determine the glycation ratio, which is a crucial metric for assessing blood glucose management efficacy, in an extensive range representing healthy and poor blood glucose management profiles. These findings provide strong evidence for the clinical potential of our biosensor architecture for point-of-care and self-assessment of diabetes management protocols.

Electrodetection of Small Molecules by Conformation-Mediated Signal Enhancement

Electrochemical biosensors allow the rapid, selective, and sensitive transduction of critical biological parameters into measurable signals. However, current electrochemical biosensors often fail to selectively and sensitively detect small molecules because of their small size and low molecular complexity. We have developed an electrochemical biosensing platform that harnesses the analyte-dependent conformational change of highly selective solute-binding proteins to amplify the redox signal generated by analyte binding. Using this platform, we constructed and characterized two biosensors that can sense leucine and glycine, respectively. We show that these biosensors can selectively and sensitively detect their targets over a wide range of concentrations-up to 7 orders of magnitude-and that the selectivity of these sensors can be readily altered by switching the bioreceptor's binding domain. Our work represents a new paradigm for the design of a family of modular electrochemical biosensors, where access to electrode surfaces can be controlled by protein conformational changes.

A pyrylium salt-based fluorescent probe for the highly sensitive detection of methylamine vapour

The MTPY exhibits an obvious fluorescence response from yellow to cyan when reacted with CH3NH2 with a low detection limit (2.6 ppt, 8.4 × 10−8 M). The sensing mechanism was traced by mass spectrometry.

Modified Screen Printed Electrode Suitable for Electrochemical Measurements in Gas Phase

We describe a convenient assembly for screen printed carbon electrodes (SPCE) suitable for analyses in gaseous samples which are of course lacking in supporting electrolytes. It consists of a circular crown of filter paper, soaked in a RTIL or a DES, placed upon a disposable screen printed carbon cell, so as to contact the outer edge of the carbon disk working electrode, as well as peripheral counter and reference electrodes. The electrical contact between the paper crown soaked in RTIL or DES and SPCE electrodes is assured by a gasket, and all components are installed in a polylactic acid holder. As a result of this configuration, a sensitive, fast-responding, membrane-free gas sensor is achieved where the real working electrode surface is the boundary zone of the carbon working disk contacted by the paper crown soaked in the polyelectrolyte. This assembly provides a portable and disposable electrochemical platform, assembled by the easy immobilization onto a porous and inexpensive supporting material such as paper of RTILs or DESs which are characterized by profitable electrical conductivity and negligible vapor pressure. The electroanalytical performance of this device was evaluated by voltammetric and flow injection analyses of oxygen which was chosen as prototype of electroactive gaseous analytes. The results obtained pointed out that this assembly is very profitable for the analysis of gaseous atmospheres, especially when used as detector for FIA in gaseous streams.

Theoretical study on the optical response behavior to hydrogen chloride gas of a series of Schiff-base-based star-shaped structures

Schiff-base compounds have many applications in the field of optoelectronic materials and chemical sensing because of their appealing coordination ability, and simple and easily accessible use in structural modification. Herein, five kinds of star-shaped Schiff-base compounds were designed and their optical response behavior to hydrogen chloride (HCl) gas was studied using dependent/time-dependent density functional theory (DFT/TDDFT). Moreover, the relationship between structures and properties was investigated upon changing the benzene group into N atom or triazine group at the core-position and introducing a methoxyl (-OCH₃) or nitro (-NO₂) group into the star-shaped Schiff-bases at the tail of the branches. The results show that all five Schiff-bases could be candidates for HCl gas sensing materials. Furthermore, introducing an electron-donating group at either the core or the tail forms a charge transfer channel with the electron deficient H-bonded imino group, which is convenient for charge transfer and subsequently promotes a red-shift in absorption spectra and fluorescence quenching.

Screen-Printed Graphite Electrodes as Low-Cost Devices for Oxygen Gas Detection in Room-Temperature Ionic Liquids

Screen-printed graphite electrodes (SPGEs) have been used for the first time as platforms to detect oxygen gas in room-temperature ionic liquids (RTILs). Up until now, carbon-based SPEs have shown inferior behaviour compared to platinum and gold SPEs for gas sensing with RTIL solvents. The electrochemical reduction of oxygen (O₂) in a range of RTILs has therefore been explored on home-made SPGEs, and is compared to the behaviour on commercially-available carbon SPEs (C-SPEs). Six common RTILs are initially employed for O₂ detection using cyclic voltammetry (CV), and two RTILs ([C₂mim][NTf₂] and [C₄mim][PF₆]) chosen for further detailed analytical studies. Long-term chronoamperometry (LTCA) was also performed to test the ability of the sensor surface for real-time gas monitoring. Both CV and LTCA gave linear calibration graphs-for CV in the 10-100% vol. range, and for LTCA in the 0.1-20% vol. range-on the SPGE. The responses on the SPGE were far superior to the commercial C-SPEs; more instability in the electrochemical responses were observed on the C-SPEs, together with some breaking-up or dissolution of the electrode surface materials. This study highlights that not all screen-printed ink formulations are compatible with RTIL solvents for longer-term electrochemical experiments, and that the choice of RTIL is also important. Overall, the low-cost SPGEs appear to be promising platforms for the detection of O₂, particularly in [C₄mim][PF₆].

Electrochemical studies of hydrogen chloride gas in several room temperature ionic liquids: mechanism and sensing

The behaviour of HCl in six RTILs reveals significant reactions with [PF₆]⁻ anions, but electrochemical sensing is still possible in RTILs with [NTf₂]⁻ anions.