Intensity-Stabilized Fast-Scanned Direct Absorption Spectroscopy Instrumentation Based on a Distributed Feedback Laser with Detection Sensitivity down to 4 × 10-6

Highly Sensitive, Calibration-Free WM-DAS Method for Recovering Absorbance-Part II: Experimental Analysis

Following the theoretical work in Part I, in this experimental study, the robustness, temporal resolution, and the narrow scan performance of the proposed wavelength modulation-direct absorption spectroscopy (WM-DAS) method are experimentally validated in a high-temperature tube furnace. The electromagnetic and other random-frequency noises can be effectively eliminated by extracting the characteristic spectra of the light intensity. The performance of WM-DAS with modulation frequencies from 0.1 to 100 kHz and scan indexes from 3.3 to 11.1 are also investigated at atmospheric pressure. The proposed method produces accurate line profile and high SNR over 500 consistently even with a weak absorption. As for real applications, the spectral line parameters of CO at 4300.6999 cm-1 including the collisional broadening, Dicke narrowing, and their dependence on temperature are measured. Furthermore, the high-speed measurement (1 ms) of the temperature and CO concentration of a McKenna flat flame are demonstrated.

A Wide-Range and Calibration-Free Spectrometer Which Combines Wavelength Modulation and Direct Absorption Spectroscopy with Cavity Ringdown Spectroscopy

A wide-range, calibration-free tunable diode laser spectrometer is established by combining wavelength modulation and direct absorption spectroscopy (WM-DAS) with continuous wave cavity ringdown spectroscopy (CW-CRDS). This spectrometer combines the benefits of absolute concentration measurements, wide range, and high speed, using WM-DAS with enhanced noise reduction in CW-CRDS. The accurate baseline ringdown time, τ0, is calculated by the absorption peak (measured by WM-DAS) and the ringdown time containing gas absorption information (measured by CW-CRDS at the center wavelength of the spectral line). The gas concentration is obtained without measuring τ0 in real time, thus, greatly improving the measuring speed. A WM-DAS/CW-CRDS spectrometer at 1.57 μm for CO detection was assembled for experimental validation of the multiplexing scheme over a concentration ranging from 4 ppm to 1.09% (0.1 MPa, 298 K). The measured concentration of CO at 6374.406 cm-1 shows that the dynamic range of this tunable diode laser absorption spectrometer is extendable up to five orders of magnitude and the corresponding precision is improved. The measurement speed of this spectrometer can extend up to 10 ms, and the detection limit can reach 35 ppb within 25 s.

A novel methodology to directly pre-determine the relative wavelength response of DFB laser in wavelength modulation spectroscopy

A novel methodology to directly pre-determine the relative wavelength response (RWR) of a DFB laser, in terms of a combined current linearly scanned wavelength response and current modulated wavelength response (CMWR), in wavelength modulation spectroscopy (WMS) is presented. It is shown that the assessed RWR can be used to mimic the measured response with standard deviation of discriminations that are below 3.4 × 10^-3cm^-1 under a variety of conditions. It is also shown that its performance supersedes two commonly used assessment models of the CMWR but is slightly worse than that of the third model, however with the benefit of solely using a single fitting parameter (the concentration) instead of more. When the novel method is applied to the assessment of CO₂ concentration in a Herriot-type multipass cell by using the technique of calibration-free WMS, the results show that there is virtually no difference compared to that by use of the best of the other methods. It is concluded that the novel method is more robust and simplifies the retrieval process of gas concentration.

Simultaneous Measurements of CO and CO2 Employing Wavelength Modulation Spectroscopy Using a Signal Averaging Technique at 1.578 μm

A resolved line pair was selected for simultaneous measurement of carbon monoxide (CO) and carbon dioxide (CO₂) in the near-infrared (NIR) region. The spectral lines of CO and CO₂ at 1.578 µm were measured by wavelength modulation spectroscopy (WMS)-2 f and the absorption was enhanced with a multipass absorption cell. The white noise was further reduced by averaging technology. The detection sensitivity (1σ) for the system is estimated at 2.63 × 10^-7cm^-1 for direct absorption spectroscopy. The ultimate detection limits of CO₂ and CO mixed with pure N₂ at 75 Torr are 29 parts per million (ppm) and 47 ppm, respectively. It is demonstrated that the signal is highly linear with the concentration in the range of 100-800 ppm. Based on an Allan variation analysis, the minimum detectable limit of CO₂ and CO is 7.5 and 14 ppm, respectively. The response time of the system is about 30 s and a relationship of temperature dependence was obtained. As an example, an in situ measurement of exhaust of alkane combustion emission is presented.

Wavelength modulation spectroscopy for recovering absolute absorbance

A highly sensitive, calibration-free method, wavelength modulation - direct absorption spectroscopy (WM-DAS), is proposed by extracting the characteristic frequencies of modulated laser intensity. This method combines the advantages of measuring absolute absorbance profile from calibration-free DAS with the enhanced noise rejection and high sensitivity of WMS. The preliminary validation experiment of H₂O transitions shows that the WM-DAS method improves the accuracy of the absorbance profile measurement with a best-fit standard residual of 4.9 × 10^-5. This new method might inspire new approaches to high-precision measurement of spectral line parameters and gas information with weak absorptions or industrial applications.