New Textile Sensors for In Situ Structural Health Monitoring of Textile Reinforced Thermoplastic Composites Based on the Conductive Poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) Polymer Complex

Soft Self-Assembled Mechanoelectrical Transducer Films from Conductive Microgel Waterborne Dispersions

The present study aims in the developing of new soft transducers based on sophisticated stimuli-responsive microgels that exhibit spontaneous self-assembly forming cohesive films with conductive and mechanoelectrical properties. For that, oligo(ethylene glycol)-based stimuli-responsive microgels have been synthesized using bio-inspired catechol cross-linkers by one-step batch precipitation polymerization in aqueous media. Then, 3,4-ethylene dioxyyhiophene (EDOT) has been directly polymerized onto stimuli-responsive microgels using catechol groups as the unique dopant. PEDOT location is dependent on the cross-linking density of microgel particles and EDOT amount used. Moreover, the spontaneous cohesive film formation ability of the waterborne dispersion after evaporation at soft application temperature is demonstrated. The films obtained present conductivity and enhanced mechanoelectrical properties triggered by simple finger compression. Both properties are function of the cross-linking density of the microgel seed particles and PEDOT amount incorporated. In addition, to obtain maximum electrical potential generated and the possibility to amplify it, several films in series were demonstrated to be efficient. The present material can be a potential candidate for biomedical, cosmetic, and bioelectronic applications.

Delamination Behaviour of Embedded Polymeric Sensor and Actuator Carrier Layers in Epoxy Based CFRP Laminates-A Study of Energy Release Rates

Fiber reinforced composites combine low density with high specific mechanical properties and thus became indispensable for today’s lightweight applications. In particular, carbon fibre reinforced plastic (CFRP) is broadly used for aerospace components. However, damage and failure behaviour, especially for complex fibre reinforcement set-ups and under impact loading conditions, are still not fully understood yet. Therefore, relatively large margins of safety are currently used for designing high-performance materials and structures. Technologies to functionalise the materials enabling the monitoring of the structures and thus avoiding critical conditions are considered to be key to overcoming these drawbacks. For this, sensors and actuators are bonded to the surface of the composite structures or are integrated into the composite lay-up. In case of integration, the impact on the mechanical properties of the composite materials needs to be understood in detail. Additional elements may disturb the composite structure, impeding the direct connection of the composite layers and implying the risk of reducing the interlaminar integrity by means of a lower delamination resistance. In the presented study, the possibility of adjusting the interface between the integrated actuator and sensor layers to the composite layers is investigated. Different polymer layer combinations integrated into carbon fibre reinforced composite layups are compared with respect to their interlaminar critical energy release rates GIc and GIIc. A standard aerospace unidirectionally reinforced (UD) CFRP prepreg material was used as reference material configuration. The investigations show that it is possible to enhance the mechanical properties, especially the interlaminar energy release rate by using multilayered sensor–actuator layers with Polyimide (PI) outer layers and layers with low shear stiffness in between.

Towards the Functional Ageing of Electrically Conductive and Sensing Textiles: A Review

Electronic textiles (e-textiles) have become more and more important in daily life and attracted increased attention of the scientific community over the last decade. This interdisciplinary field of interest ranges from material science, over chemistry, physics, electrical engineering, information technology to textile design. Numerous applications can already be found in sports, safety, healthcare, etc. Throughout the life of service, e-textiles undergo several exposures, e.g., mechanical stress, chemical corrosion, etc., that cause aging and functional losses in the materials. The review provides a broad and critical overview on the functional ageing of electronic textiles on different levels from fibres to fabrics. The main objective is to review possible aging mechanisms and elaborate the effect of aging on (electrical) performances of e-textiles. The review also provides an overview on different laboratory methods for the investigation on accelerated functional ageing. Finally, we try to build a model of cumulative fatigue damage theory for modelling the change of e-textile properties in their lifetime.

Melt Spinning of Highly Stretchable, Electrically Conductive Filament Yarns

Electrically conductive fibers are required for various applications in modern textile technology, e.g., the manufacturing of smart textiles and fiber composite systems with textile-based sensor and actuator systems. According to the state of the art, fine copper wires, carbon rovings, or metallized filament yarns, which offer very good electrical conductivity but low mechanical elongation capabilities, are primarily used for this purpose. However, for applications requiring highly flexible textile structures, as, for example, in the case of wearable smart textiles and fiber elastomer composites, the development of electrically conductive, elastic yarns is of great importance. Therefore, highly stretchable thermoplastic polyurethane (TPU) was compounded with electrically conductive carbon nanotubes (CNTs) and subsequently melt spun. The melt spinning technology had to be modified for the processing of highly viscous TPU–CNT compounds with fill levels of up to 6 wt.% CNT. The optimal configuration was achieved at a CNT content of 5 wt.%, providing an electrical resistance of 110 Ωcm and an elongation at break of 400%.