Mechanically-Induced Long-Period Fiber Gratings Using Laminated Plates

Exoskeleton type long-period fiber grating for cross-talk-resistance single-parameter measurement

This paper proposes a new, to the best of our knowledge, design framework of long-period fiber grating (LPFG) sensors resistant to multi-parameter cross talk. A section of hollow quartz capillary (HQC), which acts as an exoskeleton, is periodically merged with a single-mode fiber (SMF) by the arc-discharge method. The mechanical stress in the SMF is released while the thermal stress is enhanced after a high-temperature fusion process. Under the influence of the elastic-optical effect, the refractive index of the core is periodically modulated along the axial direction to form an exoskeleton long-period fiber grating (Es-LPFG). The unique exoskeleton structure not only induces mode coupling but also enables the proposed device to resist cross talk among the strain, ambient refractive index, and vector bending. The temperature is able to be measured independently with a sensitivity of 74 pm/ ^∘C. The novel Es-LPFG is promising in single-parameter sensing, mode-locked lasers, and frequency-locked gain flattening.

UV Inscription and Pressure Induced Long-Period Gratings through 3D Printed Amplitude Masks

In this work, we demonstrate for the first time the capability to inscribe long-period gratings (LPGs) with UV radiation using simple and low cost amplitude masks fabricated with a consumer grade 3D printer. The spectrum obtained for a grating with 690 µm period and 38 mm length presented good quality, showing sharp resonances (i.e., 3 dB bandwidth < 3 nm), low out-of-band loss (~0.2 dB), and dip losses up to 18 dB. Furthermore, the capability to select the resonance wavelength has been demonstrated using different amplitude mask periods. The customization of the masks makes it possible to fabricate gratings with complex structures. Additionally, the simplicity in 3D printing an amplitude mask solves the problem of the lack of amplitude masks on the market and avoids the use of high resolution motorized stages, as is the case of the point-by-point technique. Finally, the 3D printed masks were also used to induce LPGs using the mechanical pressing method. Due to the better resolution of these masks compared to ones described on the state of the art, we were able to induce gratings with higher quality, such as low out-of-band loss (0.6 dB), reduced spectral ripples, and narrow bandwidths (~3 nm).

3D printing of long period gratings for curvature applications

In this paper we will discuss a new type of long period grating (LPG) that consists on an optical fibre glued on top of a 3D printed grooved plate. The LPG performance will be tested for the case when pressure is applied transversely to the grooved plate. Results showed the appearance of attenuation bands at specific wavelengths, that grow with increasing load. The evolution of the dip power at those resonances, as function of the curvature will be shown, demonstrating the potentialities of the sensor for low cost intensity detection schemes.

Transverse Load and Temperature Sensing Using Multiplexed Long-Period Fiber Gratings

The simultaneous measurement of transverse load and temperature using two long-period fiber gratings multiplexed in the wavelength domain is presented experimentally. For this, a mechanically induced long-period fiber grating (MI-LPFG) and a long-period fiber grating inscribed by a continuous-wave CO2 laser (CO2 LPFG) are connected in cascade. First, the transverse load and the temperature measurements were individually performed by the multiplexed long-period fiber gratings configuration. The MI-LPFG is subject to a transverse load variation from 0–2000 g with steps of 500 g, whereas the CO2 LPFG is unloaded and they are kept at room temperature. Similarly, the CO2 LPFG is subject to a temperature variation from 30 to 110 °C by increments of 20 °C, while the MI-LPFG with a constant transverse load of 2000 g is kept at room temperature. Subsequently, the simultaneous measurement of the transverse load and the temperature is performed by the multiplexed long-period fiber grating following the steps outlined above. According to the experimental results, the transverse load and temperature measurement present high repeatability for the individual and simultaneous process. Moreover, the multiplexed LPFGs exhibit low cladding-mode crosstalk of transverse load and temperature. The coarse wavelength-division multiplexing (CWDM) of long-period fiber gratings is an attractive alternative technique in optical fiber distributed sensing applications.

Label-Free and Reproducible Chemical Sensor Using the Vertical-Fluid-Array Induced Optical Fiber Long Period Grating (VIOLIN)

Fiber optical refractometers have gained a substantial reputation in biological and chemical sensing domain regarding their label-free and remote-operation working mode. However, the practical breakthrough of the fiber optical bio/chemosensor is impeded by a lack of reconfigurability as well as the explicitness of the determination between bulk and surface refractive indices. In this letter, we further implement the highly flexible and reproducible long period grating called "VIOLIN" in chemical sensing area for the demonstration of moving those obstacles. In this configuration, the liquid is not only leveraged as the chemical carrier but also the periodic modulation of the optical fiber to facilitate the resonant signal. The thiol compound that is adsorbed by the fluidic substrate can be transduced to the pure alteration of the bulk refractive index of the liquid, which can be sensitively perceived by the resonant drift. Taking advantage of its freely dismantled feature, the VIOLIN sensor enables flexible reproduction and high throughput detection, yielding a new vision to the fiber optic biochemical sensing field.