Space Environmental Chamber for Planetary Studies

Autonomous Planetary Liquid Sampler (APLS) for In Situ Sample Acquisition and Handling from Liquid Environments

Many natural and artificial liquid environments, such as rivers, oceans, lakes, water storage tanks, aquariums, and urban water distribution systems, are difficult to access. As a result, technology is needed to enable autonomous liquid sampling to monitor water quality and ecosystems. Existing in situ sample acquisition and handling systems for liquid environments are currently limited to a single use and are semi-autonomous, relying on an operator. Liquid sampling systems should be robust and light and withstand long-term operation in remote locations. The system components involved in liquid sampling should be sterilisable to ensure reusability. Here, we introduce a prototype of a liquid sampler that can be used in various liquid environments and may be valuable for the scientific characterisation of different natural, remote, and planetary settings. The Autonomous Planetary Liquid Sampler (APLS) is equipped with pre-programmed, fully autonomous extraction, cleaning, and sterilisation functionalities. It can operate in temperatures between -10 °C and 60 °C and pressure of up to 0.24 MPa (~24 m depth below mean sea level on Earth). As part of the control experiment, we demonstrate its safe and robust autonomous operation in a laboratory environment using a liquid media with Bacillus subtilis. A typical sampling procedure required 28 s to extract 250 mL of liquid, 5 s to fill the MilliQ water, 25 s for circulation within the system for cleaning and disposal, and 200 s to raise the system temperature from ~30 °C ambient laboratory temperature to 150 °C. The temperature is then maintained for another 3.2 h to sterilise the critical parts, allowing a setup reset for a new experiment. In the future, the liquid sampler will be combined with various existing analytical instruments to characterise the liquid solution and enable the autonomous, systematic monitoring of liquid environments on Earth.

Experimental Investigation of the Atmosphere-Regolith Water Cycle on Present-Day Mars

The water content of the upper layers of the surface of Mars is not yet quantified. Laboratory simulations are the only feasible way to investigate this in a controlled way on Earth, and then compare it with remote and in situ observations of spacecrafts on Mars. Describing the processes that may induce changes in the water content of the surface is critical to determine the present-day habitability of the Martian surface, to understand the atmospheric water cycle, and to estimate the efficiency of future water extraction procedures from the regolith for In Situ Resource Utilization (ISRU). This paper illustrates the application of the SpaceQ facility to simulate the near-surface water cycle under Martian conditions. Rover Environmental Monitoring Station (REMS) observations at Gale crater show a non-equilibrium situation in the atmospheric H2O volume mixing ratio (VMR) at night-time, and there is a decrease in the atmospheric water content by up to 15 g/m2 within a few hours. This reduction suggests that the ground may act at night as a cold sink scavenging atmospheric water. Here, we use an experimental approach to investigate the thermodynamic and kinetics of water exchange between the atmosphere, a non-porous surface (LN2-chilled metal), various salts, Martian regolith simulant, and mixtures of salts and simulant within an environment which is close to saturation. We have conducted three experiments: the stability of pure liquid water around the vicinity of the triple point is studied in experiment 1, as well as observing the interchange of water between the atmosphere and the salts when the surface is saturated; in experiment 2, the salts were mixed with Mojave Martian Simulant (MMS) to observe changes in the texture of the regolith caused by the interaction with hydrates and liquid brines, and to quantify the potential of the Martian regolith to absorb and retain water; and experiment 3 investigates the evaporation of pure liquid water away from the triple point temperature when both the air and ground are at the same temperature and the relative humidity is near saturation. We show experimentally that frost can form spontaneously on a surface when saturation is reached and that, when the temperature is above 273.15 K (0 °C), this frost can transform into liquid water, which can persist for up to 3.5 to 4.5 h at Martian surface conditions. For comparison, we study the behavior of certain deliquescent salts that exist on the Martian surface, which can increase their mass between 32% and 85% by absorption of atmospheric water within a few hours. A mixture of these salts in a 10% concentration with simulant produces an aggregated granular structure with a water gain of approximately 18- to 50-wt%. Up to 53% of the atmospheric water was captured by the simulated ground, as pure liquid water, hydrate, or brine.

A Grain-Scale Study of Mojave Mars Simulant (MMS-1)

Space exploration has attracted significant interest by government agencies and the scientific community in recent years in an attempt to explore possible scenarios of settling of facilities on the Moon and Mars surface. One of the important components in space exploration is related with the understanding of the geophysical and geotechnical characteristics of the surfaces of planets and their natural satellites and because of the limitation of available extra-terrestrial samples, many times researchers develop simulants, which mimic the properties and characteristics of the original materials. In the present study, characterization at the grain-scale was performed on the Mojave Mars Simulant (MMS-1) with emphasis on the frictional behavior of small size samples which follow the particle-to-particle configuration. Additional characterization was performed by means of surface composition and morphology analysis and the crushing behavior of individual grains. The results from the study present for the first time the micromechanical tribological response of Mars simulant, and attempts were also made to compare the behavior of this simulant with previously published results on other types of Earth and extra-terrestrial materials. Despite some similarities between Mars and Moon simulants, the unique characteristics of the MMS-1 samples resulted in significant differences and particularly in severe damage of the grain surfaces, which was also linked to the dilation behavior at the grain-scale.

A Mars Environment Chamber Coupled with Multiple In Situ Spectral Sensors for Mars Exploration

Laboratory simulation is the only feasible way to achieve Martian environmental conditions on Earth, establishing a key link between the laboratory and Mars exploration. The mineral phases of some Martian surface materials (especially hydrated minerals), as well as their spectral features, are closely related to environmental conditions. Therefore, Martian environment simulation is necessary for Martian mineral detection and analysis. A Mars environment chamber (MEC) coupled with multiple in situ spectral sensors (VIS (visible)-NIR (near-infrared) reflectance spectroscopy, Raman spectroscopy, laser-induced breakdown spectroscopy (LIBS), and UV-VIS emission spectroscopy) was developed at Shandong University at Weihai, China. This MEC is a comprehensive research platform for Martian environmental parameter simulation, regulation, and spectral data collection. Here, the structure, function and performance of the MEC and the coupled spectral sensors were systematically investigated. The spectral characteristics of some geological samples were recorded and the effect of environmental parameter variations (such as gas pressure and temperature) on the spectral features were also acquired by using the in situ spectral sensors under various simulated Martian conditions. CO₂ glow discharge plasma was generated and its emission spectra were assigned. The MEC and its tested functional units worked well with good accuracy and repeatability. China is implementing its first Mars mission (Tianwen-1), which was launched on 23 July 2020 and successfully entered into a Mars orbit on 10 February 2021. Many preparatory works such as spectral databases and prediction model building are currently underway using MECs, which will help us build a solid foundation for real Martian spectral data analysis and interpretation.

Mimicking the Martian Hydrological Cycle: A Set-Up to Introduce Liquid Water in Vacuum

Liquid water is well known as the life ingredient as a solvent. However, so far, it has only been found in liquid state on this planetary surface. The aim of this experiment and technological development was to test if a moss sample is capable of surviving in Martian conditions. We built a system that simulates the environmental conditions of the red planet including its hydrological cycle. This laboratory facility enables us to control the water cycle in its three phases through temperature, relative humidity, hydration, and pressure with a system that injects water droplets into a vacuum chamber. We successfully simulated the daytime and nighttime of Mars by recreating water condensation and created a layer of superficial ice that protects the sample against external radiation and minimizes the loss of humidity due to evaporation to maintain a moss sample in survival conditions in this extreme environment. We performed the simulations with the design and development of different tools that recreate Martian weather in the MARTE simulation chamber.

Metabolt: An In-Situ Instrument to Characterize the Metabolic Activity of Microbial Soil Ecosystems Using Electrochemical and Gaseous Signatures

Metabolt is a portable soil incubator to characterize the metabolic activity of microbial ecosystems in soils. It measures the electrical conductivity, the redox potential, and the concentration of certain metabolism-related gases in the headspace just above a given sample of regolith. In its current design, the overall weight of Metabolt, including the soils (250 g), is 1.9 kg with a maximum power consumption of 1.5 W. Metabolt has been designed to monitor the activity of the soil microbiome for Earth and space applications. In particular, it can be used to monitor the health of soils, the atmospheric-regolith fixation, and release of gaseous species such as N₂, H₂O, CO₂, O₂, N₂O, NH₃, etc., that affect the Earth climate and atmospheric chemistry. It may be used to detect and monitor life signatures in soils, treated or untreated, as well as in controlled environments like greenhouse facilities in space, laboratory research environments like anaerobic chambers, or simulating facilities with different atmospheres and pressures. To illustrate its operation, we tested the instrument with sub-arctic soil samples at Earth environmental conditions under three different conditions: (i) no treatment (unperturbed); (ii) sterilized soil: after heating at 125 °C for 35.4 h (thermal stress); (iii) stressed soil: after adding 25% CaCl₂ brine (osmotic stress); with and without addition of 0.5% glucose solution (for control). All the samples showed some distinguishable metabolic response, however there was a time delay on its appearance which depends on the treatment applied to the samples: 80 h for thermal stress without glucose, 59 h with glucose; 36 h for osmotic stress with glucose and no significant reactivation in the pure water case. This instrument shows that, over time, there is a clear observable footprint of the electrochemical signatures in the redox profile which is complementary to the gaseous footprint of the metabolic activity through respiration.