Heater Integrated Lab-on-a-Chip Device for Rapid HLA Alleles Amplification towards Prevention of Drug Hypersensitivity

An Integrated Micro-Heating System for On-Chip Isothermal Amplification of African Swine Fever Virus Genes

The loop-mediated isothermal amplification (LAMP) is widely used in the laboratory to facilitate rapid DNA or RNA detection with a streamlined operational process, whose properties are greatly dependent on the uniformity and rise rate of temperature in the reaction chambers and the design of the primers. This paper introduces a planar micro-heater equipped with an embedded micro-temperature sensor to realize temperature tunability at a low energy cost. Moreover, a control system, based on the Wheatstone bridge and proportional, integral, and derivative (PID) control, is designed to measure and adjust the temperature of the micro-heater. The maximum temperature rise rate of the designed micro-heater is ≈8 °C s-1, and it only takes ≈60 s to reach the target temperature. Furthermore, a designed plasmid, containing the B646L gene of African Swine Fever Virus (ASFV), and a set of specific primers, are used to combine with the designed micro-heating system to implement the LAMP reaction. Finally, the lateral flow assay is used to interpret the amplification results visually. This method can achieve highly sensitive and efficient detection of ASFV within 40 min. The sensitivity of this on-chip gene detection method is 8.4 copies per reaction, holding great potential for applications in DNA and RNA amplification.

High-Performance, Easy-to-Fabricate, Nanocomposite Heater for Life Sciences and Biomedical Applications

Microheaters are used in several applications, including medical diagnostics, synthesis, environmental monitoring, and actuation. Conventional microheaters rely on thin-film electrodes microfabricated in a clean-room environment. However, low-cost alternatives based on conductive paste electrodes fabricated using printing techniques have started to emerge over the years. Here, we report a surprising effect that leads to significant electrode performance improvement as confirmed by the thorough characterization of bulk, processed, and conditioned samples. Mixing silver ink and PVA results in the solubilization of performance-hindering organic compounds. These compounds evaporate during heating cycles. The new electrodes, which reach a temperature of 80 °C within 5 min using a current of 7.0 A, display an overall 42% and 35% improvement in the mechanical (hardness) and electrical (resistivity) properties compared to pristine silver ink electrodes. To validate our results, we use the composite heater to amplify and detect parasite DNA from Trypanosoma brucei, associated with African sleeping sickness. Our LAMP test compares well with commercially available systems, confirming the excellent performance of our nanocomposite heaters. Since their fabrication relies on well-established techniques, we anticipate they will find use in a range of applications.

Rapid on-site nucleic acid testing: On-chip sample preparation, amplification, and detection, and their integration into all-in-one systems

As nucleic acid testing is playing a vital role in increasingly many research fields, the need for rapid on-site testing methods is also increasing. The test procedure often consists of three steps: Sample preparation, amplification, and detection. This review covers recent advances in on-chip methods for each of these three steps and explains the principles underlying related methods. The sample preparation process is further divided into cell lysis and nucleic acid purification, and methods for the integration of these two steps on a single chip are discussed. Under amplification, on-chip studies based on PCR and isothermal amplification are covered. Three isothermal amplification methods reported to have good resistance to PCR inhibitors are selected for discussion due to their potential for use in direct amplification. Chip designs and novel strategies employed to achieve rapid extraction/amplification with satisfactory efficiency are discussed. Four detection methods providing rapid responses (fluorescent, optical, and electrochemical detection methods, plus lateral flow assay) are evaluated for their potential in rapid on-site detection. In the final section, we discuss strategies to improve the speed of the entire procedure and to integrate all three steps onto a single chip; we also comment on recent advances, and on obstacles to reducing the cost of chip manufacture and achieving mass production. We conclude that future trends will focus on effective nucleic acid extraction via combined methods and direct amplification via isothermal methods.

Recent advances and challenges in temperature monitoring and control in microfluidic devices

Temperature is a critical-yet sometimes overlooked-parameter in microfluidics. Microfluidic devices can experience heating inside their channels during operation due to underlying physicochemical phenomena occurring therein. Such heating, whether required or not, must be monitored to ensure adequate device operation. Therefore, different techniques have been developed to measure and control temperature in microfluidic devices. In this contribution, the operating principles and applications of these techniques are reviewed. Temperature-monitoring instruments revised herein include thermocouples, thermistors, and custom-built temperature sensors. Of these, thermocouples exhibit the widest operating range; thermistors feature the highest accuracy; and custom-built temperature sensors demonstrate the best transduction. On the other hand, temperature control methods can be classified as external- or integrated-methods. Within the external methods, microheaters are shown to be the most adequate when working with biological samples, whereas Peltier elements are most useful in applications that require the development of temperature gradients. In contrast, integrated methods are based on chemical and physical properties, structural arrangements, which are characterized by their low fabrication cost and a wide range of applications. The potential integration of these platforms with the Internet of Things technology is discussed as a potential new trend in the field.

A magnetoimpedance biosensor microfluidic platform for detection of glial fibrillary acidic protein in blood for acute stroke classification

Acute stroke is the third leading cause of mortality and disability worldwide. Administration of appropriate therapy for acute stroke is critically dependent on timely classification into either ischemic or hemorrhagic subtypes, which have divergent treatment pathways. The current classification method is based on neuroimaging, which generally requires the transport of the patient to a hospital-based facility unless a mobile stroke unit is available. Plasma glial fibrillary acidic protein (GFAP) level has been identified as a useful blood-based biomarker to differentiate stroke subtypes. However, its conventional immunoassay methods are laboratory-based and time-consuming. Novel approaches for rapid stroke classification near the patients are urgently needed. Here, we report the development and testing of a microfluidic-based magnetoimpedance biosensor platform for measuring GFAP levels. The platform consists of a microfluidic chip for GFAP extraction from a blood sample and a magnetoimpedance (MI) biosensor that employs Dynabeads as a magnetic label to capture the GFAP molecules. We demonstrated the detection of recombinant GFAP protein in phosphate-buffered saline (PBS) and in mouse blood samples (detection limit 0.01 ng/mL) and of physiological GFAP in blood and plasma samples (detection limit 1.0 ng/mL) obtained from acute stroke patients. This detection level is within the range of cut-off levels required for clinical stroke subtype differentiation. This platform has the potential to be incorporated into a small device with further development to assist in the classification of acute stroke patients and clinical decision-making at the point-of-care.

Electric Cell-substrate Impedance Sensing in Biocompatibility Research

In this paper, the possibility of using cell culture impedance measurements to assess the biocompatibility of a material in contact with cells was analyzed. For this purpose, the Electric Cell-substrate Impedance Sensing (ECIS) method and a commercial measuring device were used. The test substrates with thin-film electrodes made of various metals were prepared using the magnetron sputtering method. The choice of metals was dictated by their varying degrees of biocompatibility. Cultures of mouse fibroblasts were cultured on the prepared substrates. The experiment showed that the complete cycle of culture from attachment and reproduction to apoptosis occurred. The results obtained indicate that it is possible to use the ECIS method to study the influence of metal on cell culture activity.