Optical and Electronic NO(x) Sensors for Applications in Mechatronics

Fiber Optic Gas Sensors Based on Lossy Mode Resonances and Sensing Materials Used Therefor: A Comprehensive Review

Pollution in cities induces harmful effects on human health, which continuously increases the global demand of gas sensors for air quality control and monitoring. In the same manner, the industrial sector requests new gas sensors for their productive processes. Moreover, the association between exhaled gases and a wide range of diseases or health conditions opens the door for new diagnostic applications. The large number of applications for gas sensors has permitted the development of multiple sensing technologies. Among them, optical fiber gas sensors enable their utilization in remote locations, confined spaces or hostile environments as well as corrosive or explosive atmospheres. Particularly, Lossy Mode Resonance (LMR)-based optical fiber sensors employ the traditional metal oxides used for gas sensing purposes for the generation of the resonances. Some research has been conducted on the development of LMR-based optical fiber gas sensors; however, they have not been fully exploited yet and offer optimal possibilities for improvement. This review gives the reader a complete overview of the works focused on the utilization of LMR-based optical fiber sensors for gas sensing applications, summarizing the materials used for the development of these sensors as well as the fabrication procedures and the performance of these devices.

Surface states mediated charge transfer in redox behavior of hemin at GaAs(100) electrodes

EIS and XPS investigations on the interaction of hemin with p- and n-doped GaAs(100) electrodes in PBS solution revealed significant differences concerning both the adsorbed species and the mechanism of the redox process caused by dopant nature. XPS data show that hemin is adsorbed on p-GaAs(100) by its carboxyl groups and adopts a vertical position favorable to a polymeric film formation whereas on n-GaAs(100), the adsorbed hemin is monomeric and has a rather planar configuration involving mainly the OH groups of the organic molecule. Hemin gives rise to a reversible redox process at the p-GaAs(100) electrode whereas at n-GaAs(100), there is only one reduction wave of a considerably lower current density appearing at a more negative potential. The effects of the applied potential on the phase angle measured at p-GaAs(100) point out major changes not only in the insulating properties of the adsorbed layer, as found at n-GaAs(100), but also in the electronic properties of the semiconductor triggered by the hemin redox process. Analysis of the experimental data points to a mechanism of charge transfer through surface states, the observed differences being related to the location of the surface states with respect to the formal potential of the hemin redox couple.

Paper brings evidence that surface states are responsible for different redox processes of hemin, reversible at p-GaAs(100) and ireversible at n-GaAs(100).

High sensitive detection of nitric oxide using laser induced photoacoustic spectroscopy at 213 nm

Trace level detection of nitric oxide (NO) is of great interest for a wide range of applications such as environment and human health. For this purpose, a high sensitive sensor based photoacoustic spectroscopy (PAS) principle has been developed at our laboratory for detection of NO at very low concentration (ppbV). For optimization of the PAS signal and to achieve higher sensitivity, parametric dependence investigation was carried out where PAS signal dependence on NO gas pressure, cell geometry, buffer gas (Ar, N2, He), and laser pulse energy used three PAS cells developed locally. The best sensitivity achieved with three cells was 41, 11, 20 ppbv, respectively. It is worth reporting that the best PAS signal to noise ratio was achieved by using a cylindrical cell having three acoustic filters and argon as a buffer gas.

Quantum cascade laser technology for the ultrasensitive detection of low-level nitric oxide

Several spectroscopic methods based on mid-infrared quantum cascade lasers for the ultrasensitive detection of nitric oxide have been developed with detection limit in ppbv and sub-ppbv range. We will describe here a selection of the most effective techniques, i.e., laser absorption spectroscopy, cavity-enhanced spectroscopy, photoacoustic spectroscopy, and Faraday modulation spectroscopy. For each technique, advantages and drawbacks will be underlined.

Photoacoustic techniques for trace gas sensing based on semiconductor laser sources

The paper provides an overview on the use of photoacoustic sensors based on semiconductor laser sources for the detection of trace gases. We review the results obtained using standard, differential and quartz enhanced photoacoustic techniques.