Adsorption of Chloramphenicol on Commercial and Modified Activated Carbons

Highly enhanced chloramphenicol adsorption performance of MIL-53-NH2(Al)-derived porous carbons modified with tannic acid

The worldwide demand for antibiotics has experienced a notable surge, propelled by the repercussions of the COVID-19 pandemic and advancements in the global healthcare sector. A prominent challenge confronting humanity is the unregulated release of antibiotic-laden wastewater into the environment, posing significant threats to public health. The adoption of affordable carbon-based adsorbents emerges as a promising strategy for mitigating the contamination of antibiotic wastewater. Here, we report the synthesis of novel porous carbons (MPC) through a direct pyrolysis of MIL-53-NH2(Al) and tannic acid (TANA) under N2 atmosphere at 800 °C for 4 h. The effect of TANA amount ratios (0%-20%, wt wt-1) on porous carbon structure and adsorption performance was investigated. Results showed that TANA modification resulted in decreased surface area (1,600 m2 g-1-949 m2 g-1) and pore volume (2.3 cm3 g-1-1.7 cm3 g-1), but supplied hydroxyl functional groups. Adsorption kinetic, intraparticle diffusion, and isotherm were examined, indicating the best fit of Elovich and Langmuir models. 10%-TANA-MPC obtained an ultrahigh adsorption capacity of 564.4 mg g-1, which was approximately 2.1 times higher than that of unmodified porous carbon. 10%-TANA-MPC could be easily recycled up to 5 times, and after reuse, this adsorbent still remained highly stable in morphology and surface area. The contribution of H bonding, pore-filling, electrostatic and π-π interactions to chloramphenicol adsorption was clarified. It is recommended that TANA-modified MIL-53-NH2(Al)-derived porous carbons act as a potential adsorbent for removal of pollutants effectively.

Effect of pyrolysis temperature on characteristics and chloramphenicol adsorption performance of NH2-MIL-53(Al)-derived amine-functionalized porous carbons

Several activities such as aquaculture, human and feedstock therapies can directly release antibiotics into water. Due to high stability, low hydrolysis and non-biodegradation, they can accumulate in the aqueous environment and transport to aquatic species. Here, we synthesized amine-functionalized porous carbons (ANC) by a direct-pyrolysis process of NH2-MIL-53(Al) as a sacrificial template at between 600 and 900 °C and utilized them to eliminate chloramphenicol antibiotic from water. The NH2-MIL-53(Al)-derived porous carbons obtained high surface areas (304.7-1600 m2 g-1) and chloramphenicol adsorption capacities (148.3-261.5 mg g-1). Several factors such as hydrogen bonding, Yoshida hydrogen bonding, and π-π interaction, hydrophobic interaction possibly controlled adsorption mechanisms. The ANC800 could be reused four cycles along with high stability in structure. As a result, NH2-MIL-53(Al)-derived porous carbons are recommended as recyclable and efficient adsorbents to the treatment of antibiotics in water.

Simple synthesis of BiOI/ZnO/rGO for efficient photocatalytic degradation of antibiotic chloramphenicol under visible light

BiOI/ZnO/rGO (reduced graphene oxide) composite photocatalyst was fabricated using a simple one-step hydrothermal process and applied to the degradation of antibiotic chloramphenicol (CAP). By tuning the Bi/Zn ratios, the structure and photoelectric properties of the catalyst were investigated and characterized in terms of their morphological, structural, optical and photoelectrochemical properties. The as-synthesized composite photocatalysts are well-crystalline, uniform dispersion and exhibit good photocatalytic properties. The photocatalytic degradation rate of CAP by BiOI/ZnO/rGO composite is 8.1 times and 1.8 times that of BiOI and ZnO, respectively. The photocatalytic mechanism studies revealed that the synergistic effect between rGO and BiOI/ZnO can effectively separate photogenerated electron-hole, enhance photocurrents and conductivity, and improve charge carrier densities. Moreover, BiOI/ZnO/rGO possesses good stability and reusability that the degradation efficiency remained above 80% even after 5 recycling. This study reveals that both the introduction of rGO and heterostructure construction between BiOI and ZnO play a crucial role in their photoelectrochemical and photocatalytic properties.

Biosorption Potential of Microbial and Residual Biomass of Saccharomyces pastorianus Immobilized in Calcium Alginate Matrix for Pharmaceuticals Removal from Aqueous Solutions

Two types of biosorbents, based on Saccharomyces pastorianus immobilized in calcium alginate, were studied for the removal of pharmaceuticals from aqueous solutions. Synthetized biocomposite materials were characterized chemically and morphologically, both before and after simulated biosorption. Ethacridine lactate (EL) was chosen as a target molecule. The process performance was interpreted as a function of initial solution pH, biosorbent dose, and initial pharmaceutical concentration. The results exhibited that the removal efficiencies were superior to 90% for both biosorbents, at the initial pH value of 4.0 and biosorbent dose of 2 g/L for all EL initial concentrations tested. Freundlich, Temkin, Hill, Redlich-Peterson, Sips, and Toth isotherms were used to describe the experimental results. The kinetic data were analyzed using kinetic models, such as pseudo-first order, pseudo-second order, Elovich, and Avrami, to determine the kinetic parameters and describe the transport mechanisms of EL from aqueous solution onto biosorbents. Among the tested equations, the best fit is ensured by the pseudo-second-order kinetics model for both biosorbents, with the correlation coefficient having values higher than 0.996. The many potential advantages and good biosorptive capacity of Saccharomyces pastorianus biomass immobilized in calcium alginate recommend these types of biocomposite materials for the removal of pharmaceuticals from aqueous solutions.

Development of a Citric-Acid-Modified Cellulose Adsorbent Derived from Moringa peregrina Leaf for Adsorptive Removal of Citalopram HBr in Aqueous Solutions

A citric-acid-modified Moringa peregrina leaf substrate was prepared and studied as an effective adsorbent for the adsorptive removal of citalopram HBr (CTM). FTIR spectra were utilized to characterize the prepared solid. The effects of experimental variables on the percentage removal of citalopram HBr were investigated using response surface methodology. The optimum conditions selected for removal of CTM were 7 and 4 min, 0.17 g per 50 mL and 35 mg·L⁻¹ for pH, contact time, adsorbent dose and initial concentration of CTM, respectively. Under the optimized experimental conditions, 82.59% CTM (35 mg·L⁻¹) was removed. The Langmuir isotherm, Freundlich isotherm, pseudo second-order kinetic model and diffusion-chemisorption model explained the adsorption data successfully. The maximum adsorption capacity at 298 K was 8.58 mg·g⁻¹. A thermodynamic study illustrated that CTM adsorption was spontaneous and endothermic in nature.

Occurrence, toxicity and adsorptive removal of the chloramphenicol antibiotic in water: a review

Chloramphenicol is a broad-spectrum bacterial antibiotic used against conjunctivitis, meningitis, plague, cholera, and typhoid fever. As a consequence, chloramphenicol ends up polluting the aquatic environment, wastewater treatment plants, and hospital wastewaters, thus disrupting ecosystems and inducing microbial resistance. Here, we review the occurrence, toxicity, and removal of chloramphenicol with emphasis on adsorption techniques. We present the adsorption performance of adsorbents such as biochar, activated carbon, porous carbon, metal-organic framework, composites, zeolites, minerals, molecularly imprinted polymers, and multi-walled carbon nanotubes. The effect of dose, pH, temperature, initial concentration, and contact time is discussed. Adsorption is controlled by π-π interactions, donor-acceptor interactions, hydrogen bonding, and electrostatic interactions. We also discuss isotherms, kinetics, thermodynamic data, selection of eluents, desorption efficiency, and regeneration of adsorbents. Porous carbon-based adsorbents exhibit excellent adsorption capacities of 500-1240 mg g^-1. Most adsorbents can be reused over at least four cycles.

Removal efficiency of pharmaceutical drugs (Mebeverine hydrochloride MEB) by an activated carbon prepared from dates stems

The removal efficiency of the pharmaceutical drug Mebeverine Hydrochloride (MEB) from solutions by an activated carbon (AC) prepared from dates stems was investigated in the present research work. The surface properties of the activated carbon were investigated by elementary analysis, BET surface area, SEM, FTIR and pH_pzc. The operating parameters effect on the MEB adsorption efficiency was investigated by using batch experiments. The adsorption isotherms study indicated that the experimental data were well described by Freundlich and DR isotherms, with the maximum adsorption capacity (q_max) of 4105 mg/g. This result suggests the multilayer adsorption of MEB on the activated carbon.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s40201-021-00658-1.

Peanut shells-derived biochars prepared from different carbonization processes: Comparison of characterization and mechanism of naproxen adsorption in water

The ubiquitous appearance of nonsteroidal anti-inflammatory drugs (i.e., naproxen) in water bodies has raised enormous concerns among general public. Development of promising materials for eliminating such contaminants from water environment has attracted much attention in the scientific community. In this study, three (direct, post-treated and pre-treated) methods were developed to prepare biochars (800-PSB, 800-800-PSB, and 190-800-PSB, respectively) derived from the wastes of peanut shells (PS). They were thoroughly characterized by various important properties (i.e., porosity and superficial functional group) and applied to remove naproxen drug from water. Results indicated that although the pre- and post-treatments had a slight effect on the surface area of biochars (i.e., 571 m²/g for 800-PSB, 596 m²/g for 800-800-PSB, and 496 m²/g for 190-800-PSB), such treatments remarkably improved the adsorption capacity of biochar. The maximum adsorption capacity of biochar (obtained from the Langmuir model) towards naproxen in solution at 25 decreased in the following order: 800-800-PSB (324 mg/g) > 190-800-PSB (215 mg/g) > 800-PSB (105 mg/g). The thermodynamic study demonstrated that the adsorption was spontaneous and exothermic. Depending the preparation process, the contribution of each mechanism in the adsorption process was dissimilar. The overall adsorption mechanism was regarded as pore filling, π-π interaction, hydrogen bonding formations, n-π interaction, van der Waals force, and electrostatic attraction. Two methods used to identify the important role of π-π interaction were proposed herein. The possible desorption and reuse of laden-biochars were investigated by the chemical and thermal methods. The prepared biochar samples can serve as potential carbonaceous porous adsorbents for effectively removing naproxen from water media.

Chemically Modified Biosorbents and Their Role in the Removal of Emerging Pharmaceutical Waste in the Water System

Presence of pharmaceutically active compounds (PACs) as emerging contaminants in water is a major concern. Recent reports have confirmed the presence of PACs in natural and wastewater systems, which have caused several problems indicating the urgent need for their removal. The current review evaluates the role of chemically modified biosorbents in the removal of PACs in water. Reported biosorbents include plant and animal solid waste, microorganisms and bio-composite. Bio-composites exhibited better prospects when compared with other biosorbents. Types of chemical treatment reported include acid, alkaline, solvent extraction, metal salt impregnation and surface grafting, with alkaline treatment exhibiting better results when compared with other treatments. The biosorption processes mostly obeyed the pseudo-second-order model and the Langmuir isotherm model in a process described mainly by ionic interaction. Desorption and regeneration capacity are very important in selecting an appropriate biosorbent for the biosorption process. Depending on the type of biosorbent, the cost of water treatment per million liters of water was estimated as US $10–US $200, which presents biosorption as a cheap process compared to other known water treatment processes. However, there is a need to conduct large-scale studies on the biosorption process for removing PACs in water.

Assessment of ampicillin removal efficiency from aqueous solution by polydopamine/zirconium(iv) iodate: optimization by response surface methodology

Polydopamine/zirconium(iv) iodate was prepared by incorporating polydopamine into zirconium iodate gel and studied as an effective adsorbent for ampicillin. In order to characterize the prepared composite, FTIR, XRD, TGA-DTA, SEM and TEM were used. The effects of experimental variables on ampicillin removal were examined using response surface methodology. The optimum conditions for ampicillin removal were 7, 130 min, 20 mg/20 mL and 50 mg L-1 for pH, contact time, adsorbent dose and initial ampicillin concentration, respectively. Under the optimum conditions, the maximum ampicillin removal percentage was found to be 99.12%. The Langmuir isotherm and pseudo-second-order kinetic models explained the removal process more appropriately. The maximum adsorption capacity at 303 K was 100.0 mg g-1. Thermodynamic study revealed that the ampicillin adsorption was spontaneous and endothermic in nature. The reusability of the prepared material was also explored.

The Potentiality of Rice Husk-Derived Activated Carbon: From Synthesis to Application

Activated carbon (AC) has been extensively utilized as an adsorbent over the past few decades. AC has widespread applications, including the removal of different contaminants from water and wastewater, and it is also being used in capacitors, battery electrodes, catalytic supports, and gas storage materials because of its specific characteristics e.g., high surface area with electrical properties. The production of AC from naturally occurring precursors (e.g., coal, biomass, coconut shell, sugarcane bagasse, and so on) is highly interesting in terms of the material applications in chemistry; however, recently much focus has been placed on the use of agricultural wastes (e.g., rice husk) to produce AC. Rice husk (RH) is an abundant as well as cheap material which can be converted into AC for various applications. Various pollutants such as textile dyes, organic contaminants, inorganic anions, pesticides, and heavy metals can be effectively removed by RH-derived AC. In addition, RH-derived AC has been applied in supercapacitors, electrodes for Li-ion batteries, catalytic support, and energy storage, among other uses. Cost-effective synthesis of AC can be an alternative for AC production. Therefore, this review mainly covers different synthetic routes and applications of AC produced from RH precursors. Different environmental, catalytic, and energy applications have been pinpointed. Furthermore, AC regeneration, desorption, and relevant environmental concerns have also been covered. Future scopes for further research and development activities are also discussed. Overall, it was found that RH-derived AC has great potential for different applications which can be further explored at real scales, i.e., for industrial applications in the future.

Chromium (VI) Adsorption on Modified Activated Carbons

The paper presents the research of adsorptive properties of activated carbons to chromium (VI) removal from the water solution. Different types of carbon were investigated: WD-ekstra (WDA), WD-ekstra modified by salt acid WD(HCl) and nitrogen acid WD(HNO3). The adsorption kinetics, influence reaction, temperature and kind of carbon were determined using static methods. The adsorption of chromium (VI) onto all activated carbons was most efficient at pH 2. The time of adsorption balance for carbon WD(HCl) was 2.5 h and for carbon WDA 4.5 h. The influence of carbon modification and temperature on the effectiveness of adsorption of hexavalent chromium was determined on the basis of the Freundlich adsorption isotherm. The research showed that the adsorption capacity of Cr(VI) increased with the increasing temperature of the solution. The most efficient adsorbent in static conditions was found on WD-ekstra modified by HCl. The adsorbent applied in dynamic conditions as the filtration bed (v = 2 m/h, time of retention TR = 420 s, initial concentration C0 = 1 mg/dm3), it removed chromium (VI) from water very effectively. Adsorption capacities after exhaustion of the bed were obtained at PeWD (HCl) = 4.35 mg/g. On the basis of executed research, chromium ions were successfully eliminated onto modified carbon WD(HCl) that makes its employment capabilities in the systems purification of water.