Phosphorus and Nitrogen Adsorption Capacities of Biochars Derived from Feedstocks at Different Pyrolysis Temperatures

Functionalized biochar from waste as a slow-release nutrient source: Application on tomato plants

Licorice processing waste was pyrolyzed at different temperatures (500 and 700 °C) to obtain biochar (BC500 and BC700) for use as a slow-release fertilizer on Solanum lycopersicum. The materials were characterized through BET analysis, SEM, elemental analysis, pHzc, and pyrolysis temperature effect was evaluated. The biochars were functionalized by the impregnation method to enrich them with nitrogen, phosphorus, and potassium (NPK), and desorption tests were performed in aqueous solution at different pHs (5 and 7). The pseudo-second-order model described well the release of all 3 macronutrients tested, BC500 was found to have slower release kinetics due to smaller pore size, reaching adsorption/desorption equilibrium after 14 days, compared with 10 for BC700, Kdes were lower in all 3 cases and NPK content was higher, initial pH did not change the release kinetics. BC500 was selected as an agricultural soil conditioner by testing at both different dosages of BC (0-25 %) and different NPK ratios (3:1:4 and 4:1:3). The treatment significance was evaluated. The best treatment resulted in BC dosage of 25 % nutrient ratio 4:1:3 which increased, compared to the control, total chlorophyll content (+38 %) and carotenoids (+15 %).

Potential use of Ulva intestinalis-derived biochar adsorbing phosphate ions in the cultivation of winter wheat Tristicum aestivum

In this work, the properties of biochar produced from green macroalga Ulva intestinalis by pyrolysis were studied at temperatures of 300, 500, and 700 °C. This biochar was characterized in terms of multielemental composition, BET surface area, total pore volume, and biosorption properties toward phosphate ions. Biochar produced at 700 °C-25 m2/g had the highest surface area. The kinetics and isotherms of sorption processes of phosphate ions as sorbate by these sorbents were investigated. Modified biochar was able to remove 84.3% of phosphate ions from wastewater, whereas non-modified biochar-only 40.6%. Hence, biochar enriched with phosphate ions can serve as a valuable soil amendment. Pot experiments performed on winter wheat (Triticum aestivum) with a 3% addition of dry Ulva intestinalis, pristine biochar, and Mg-modified biochar enriched with phosphate ions showed that these amendments stimulated plant growth (length and fresh weight of plants) as well as enlarging the chlorophyll content in leaves. Our results indicate that the production of biochar (pristine and Mg-impregnated) is a sustainable option to valorize the biomass of seaweeds, and to recycle phosphorus from wastewater.

Screening the optimal modified biochar for nitrogen retention in black soil

Reducing the environmental problems caused by nitrogen loss and nitrogen pollution is of great significance. The addition of biochar to soil is a new method for increasing nitrogen interception due to the special structural and physicochemical properties of biochar. The optimal modified biochar was screened out after acid-base modification and batch adsorption test in this paper. And then the effects of different soil and biochar mixing methods on soil physicochemical properties and nitrogen adsorption and retention were explored through soil column leaching test. The results showed that the biochar with a pyrolysis temperature of 700 °C had the best adsorption effect on nitrogen after being modified by 0.1 mol/L HCI, and the adsorption capacity of nitrate nitrogen reached 121.46 mg/g. The adsorption process of ammonia nitrogen and nitrate nitrogen conformed to the Langmuir model and was mainly homogeneous monolayer. After mixing the selected modified biochar with black soil, the pH increased by 4.77%, the content of ammonia nitrogen increased by 4.89%, and the nitrate content increased by 16.62%. In this study, the adsorption effect of biochar on nitrogen in black soil was discussed, so as to explore the optimal use of biochar in soil, which provided some reference basis for the relevant research.

Nitrate-Nitrogen Adsorption Characteristics and Mechanisms of Various Garden Waste Biochars

Nitrate-nitrogen (NO3--N) removal and garden waste disposal are critical concerns in urban environmental protection. In this study, biochars were produced by pyrolyzing various garden waste materials, including grass clippings (GC), Rosa chinensis Jacq. branches (RC), Prunus persica branches (PP), Armeniaca vulgaris Lam. branches (AV), Morus alba Linn. sp. branches (MA), Platycladus orientalis (L.) Franco branches (PO), Pinus tabuliformis Carrière branches (PT), and Sophorajaponica Linn. branches (SL) at three different temperatures (300 °C, 500 °C, and 700 °C). These biochars, labeled as GC300, GC500, GC700, and so on., were then used to adsorb NO3--N under various conditions, such as initial pH value, contact time, initial NO3--N concentration, and biochar dosage. Kinetic data were analyzed by pseudo-first-order and pseudo-second-order kinetic models. The equilibrium adsorption data were evaluated by Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models. The results revealed that the biochar yields varied between 14.43% (PT700) and 47.09% (AV300) and were significantly influenced by the type of garden waste and decreased with increasing pyrolysis temperature, while the pH and ash content showed an opposite trend (p < 0.05). The efficiency of NO3--N removal was significantly influenced by the type of feedstock, preparation process, and adsorption conditions. Higher pH values had a negative influence on NO3--N adsorption, while longer contact time, higher initial concentration of NO3--N, and increased biochar dosage positively affected NO3--N adsorption. Most of the kinetic data were better fitted to the pseudo-second-order kinetic model (0.998 > R2 > 0.927). Positive b values obtained from the Temkin model indicated an exothermic process of NO3--N adsorption. The Langmuir model provided better fits for more equilibrium adsorption data than the Freundlich model, with the maximum NO3--N removal efficiency (62.11%) and adsorption capacity (1.339 mg·g-1) in PO700 under the conditions of pH = 2, biochar dosage = 50 mg·L-1, and a reaction time of 24 h. The outcomes of this study contribute valuable insights into garden waste disposal and NO3--N removal from wastewater, providing a theoretical basis for sustainable environmental management practices.

Effect of the Co-Application of Eucalyptus Wood Biochar and Chemical Fertilizer for the Remediation of Multimetal (Cr, Zn, Ni, and Co) Contaminated Soil

Contamination of soil with heavy metals is a worldwide problem, which causes heavy metals to release into the environment. Remediation of such contaminated soil is essential to protect the environment. The aims of this study are: first, to compare the effect of biochar and the joint application of biochar with fertilizer for the phytoremediation of heavy metals-contaminated soil using Acacia auriculiformis; second, to study the effect of the application rate of biochar in improving the physicochemical properties of the soil. The soil samples were collected from an active coal mine dump and assessed for their physicochemical properties and heavy metals toxicity. Initial results indicated that the soil has poor physicochemical properties and was contaminated with the presence of heavy metals such as Zn, Ni, Cu, Cr, and Co. Later, the heavy metals-contaminated soil was mixed with the 400 and 600 °C biochar, as well as the respective biochar–fertilizer combination in varying mixing ratios from 0.5 to 5% (w/w) and subjected to a pot-culture study. The results showed that the application of both varieties of biochar in combination with fertilizer substantially improved the physicochemical properties and reduced the heavy metals toxicity in the soil. The biochar and fertilizer joint application also substantially improved the soil physiochemical properties by increasing the application rate of both varieties of biochar from 0.5 to 5%. The soil fertility index (SFI) of the biochar and biochar–fertilizer amended soil increased by 49.46 and 52.22%, respectively. The plant’s physiological analysis results indicated a substantial increase in the plant’s shoot and root biomass through the application of biochar and biochar–fertilizer compared to the control. On the other hand, it significantly reduced the heavy metals accumulation and, hence, the secretion of proline and glutathione hormones in the plant cells. Therefore, it can be concluded that the joint application of biochar with the application rate varying between 2.5 to 5% (w/w) with the fertilizer significantly improved the physicochemical properties of the soil and reduced the heavy metals toxicity compared to the controlled study.

Biochar application in biofiltration systems to remove nutrients, pathogens, and pharmaceutical and personal care products from wastewater

Although conventional on-site wastewater treatment systems (OWTSs) provide only primary treatment of domestic wastewater, removal of a limited level of nutrients (N, P), pathogens, and pharmaceuticals and personal care products (PPCPs) could be achieved by such a treatment process. Biochar has the capacity to remove various contaminants and has been widely used as an ideal soil amendment in agriculture due to its persistence, superior nutrient-retention properties, low cost, and ready availability. However, few applications on the use of biochar in onsite wastewater treatment have been explored. In this review, we systematically reviewed the applications of biochar in filtration-based OWTSs for nutrient (N, P) removal and recovery as well as pathogen and PPCP removal. Although adsorption was the main mechanism for P, pathogen, and PPCP removal, biochar can also serve as the growth media for enhanced biological degradation, improves available alkalinity, and increases water holding capacity in the OWTSs. The biochar source, surface modification methods, and preparation procedures (e.g., pyrolysis temperature change) have significant effects on contaminant removal performance in biochar-amended OWTSs. Specifically, contradictory results have been reported on the effect of pyrolysis temperature change on biochar removal performance (i.e., increased, decreased, or no change) of N, P, and PPCPs. Wastewater composition and environmental pH also play important roles in the removal of nutrients, pathogens, and PPCPs. Overall, biochar holds great potential to serve as an alternative filtration material or to be amended to the current OWTS to improve system performance in removing a variety of contaminants at low cost.

Dynamic Adsorption Characteristics of Phosphorus Using MBCQ

Biochar is a new type of adsorption material with excellent performance, but it has some problems, such as light texture, poor sedimentation, and difficult recovery, which limits its practical application. In this study, biochar microspheres (MBCQ) were prepared by the sol–gel method using powdery biochar from Hydrocotyle vulgaris as raw material and sodium alginate as a granular carrier. Experiments were performed to investigate the dynamic adsorption characteristics of phosphorus by MBCQ in the adsorption column and the influences of particle size, initial phosphorus concentration, flow rate, and column height on the breakthrough curve. The results showed that the static adsorption properties of different particles varied and that 3-millimeter particles were optimal. The breakthrough time positively correlated with column height and negatively correlated with initial phosphorus concentration, flow rate, and particle size. Flow velocity significantly impacted breakthrough time and length of mass transfer. The bed depth/service time model accurately predicted the relationship between breakthrough times and column heights. When ct/c0 = 0.6, the average relative deviation between predicted and measured values was the lowest. The Thomas model described the MBCQ adsorption process of Ph (R2 > 0.95), which indicated that diffusion in MBCQ adsorption was not a rate-limiting step.

Recycling rice husk for removal of phosphate and nitrate from synthetic and swine wastewater: Adsorption study and nutrient analysis of modified rice husk

The objective of this study was to determine the adsorbent potential of rice husk and its modified form for phosphate and nitrate removal from synthetic and swine-farm wastewater. The mechanism of adsorption as well as the potential of phosphate-/nitrate- adsorbed rice husk as nutrient rich residue was also investigated. Two-step modification of RH (using base-washing (BW) and chemical modification (CM) was conducted to compare the phosphate and nitrate removal. The effects of several factors (pH, sorbent dosage, contact time, initial concentration, and coexistence of both ions) were investigated to gain insight into the adsorption rate, behavior, and mechanism of the modified RH regarding phosphate and nitrate removal. The results of Fourier-transform infrared spectroscopy showed that the modification was successful by crosslinking with the amine group of the chemical agent. Fitting the adsorption kinetic data of phosphate showed physical adsorption, intraparticle diffusion, and chemisorption, whereas for nitrate, the data indicated mainly chemisorption. Fitting the adsorption isotherm data of phosphate and nitrate together showed adsorption on a monolayer coating of anions on the homogeneous sorbent's surface. The maximum phosphate and nitrate adsorption capacities were 6.94 and 2.46 mg/g, respectively, for a single adsorbate and 11.14 and 1.76 mg/g, respectively, for the binary solution. In real swine wastewater, removal efficiencies of phosphate, nitrite, nitrate, sulfate, and ammonia were 83.8%, 65.0%, >45.0%, 36.6%, and 2.6%, respectively, indicating that the modified RH would be effective for phosphate and nitrate removal from real wastewater. Finally, nutrient analysis of the phosphate- and nitrate-sorbed RH showed increases in nitrogen and phosphorus, which would be beneficial for further use of the RH as nutrient or fertilizer after adsorption.

Modification of Hardwood Derived Biochar to Improve Phosphorus Adsorption

The excessive application of phosphorus in agricultural lands leads to serious environmental issues. Efficient application is beneficial from an economic and environmental perspectives. Biochar can be used as a carrier for slow release of phosphate. However, its adsorption capacity is limited. In this work, biochar was prepared at different pyrolysis temperatures (350–550 °C). The biochar prepared at 550 °C had the highest adsorption capacity and was selected for modification by magnesium impregnation. Magnesium modification enhanced the adsorption capacity by 34% to a theoretical max adsorption capacity of 463.5 mg·g−1. The adsorbed phosphate can be desorbed. The desorption was bi-phasic with fast- and slow-release fractions. The distribution of the phosphate fractions was pH dependent with slow release being most prominent in neutral conditions. Mg modified biochar can be used to recover phosphate and then used as a carrier for slow release of phosphate. The bi-phasic desorption behaviour is useful as the fast release fraction can provide the immediate phosphate needed during plant establishment, while the slow-release fraction maintains steady supply over extended periods.

The Recovery of Phosphate and Ammonium from Biogas Slurry as Value-Added Fertilizer by Biochar and Struvite Co-Precipitation

Biowaste materials could be considered a renewable source of fertilizer if methods for recovering P from waste can be developed. Over the last few decades, there has been a high level of interest in using biochar to remove contaminants from aqueous solutions. This study was conducted using a range of salts that are commonly found in biogas slurry (ZnCl2, FeCl3, FeCl2, CuCl2, Na2CO3, and NaHCO3). Experiments with a biogas digester and aqueous solution were conducted at pH nine integration with NH4+, Mg2+, and PO43− molar ratios of 1.0, 1.2, and 1.8, respectively. The chemical analysis was measured to find out the composition of the precipitate, and struvite was employed to remove the aqueous solutions. The study found that the most efficient removal of phosphate and ammonium occurred at pH nine in Tongan sludge urban biochar and rice biochar, respectively. Increasing the concentration of phosphate and ammonium increased the phosphate and ammonium content. Moreover, increasing the biochar temperature and increasing the concentration of phosphate and ammonium increased the efficiency of the removal of ammonium and phosphate. The removal efficiency of ammonium and phosphate increased from 15.0% to 71.0% and 18.0% to 99.0%, respectively, by increasing the dose of respective ions K+, Zn2+, Fe3+, Fe2+, Cu2+, and CO32.The elements were increased from 58.0 to 71.0 for HCO3− with the increasing concentration from 30 mg L−1 to 240 mg L−1.This study concluded that phosphate and ammonium can be recovered from mushroom soil biochar and rice biochar, and phosphate can be effectively recovered via the struvite precipitation method.

Phosphorus Removal from Wastewater: The Potential Use of Biochar and the Key Controlling Factors

In recent years, a large volume of literature has been published regarding the removal of phosphorus (P) from wastewater. Various sorbing materials, such as metal oxides and hydroxides, carbonates and hydroxides of calcium (Ca) and magnesium (Mg), hydrotalcite, activated carbon, anion exchange resins, industrial solid wastes and organic solid wastes, have been suggested for P removal. Many of these sorbents are expensive and/or may cause some environmental problems. In contrast, biochar, as an economical and environmentally friendly sorbing material, has received much attention in recent years and has been used as a novel sorbent for the removal of different organic and inorganic pollutants. Biochar is a type of sustainable carbonaceous material that is produced from the thermal treatment of agricultural organic residues and other organic waste streams under oxygen free conditions. This paper reviews the potential use of biochar and the key controlling factors affecting P removal from wastewater. The ability of biochar to remove P from wastewater depends on its physical and chemical properties. Some of the most important physicochemical properties of biochar (structural characteristics, electrical conductivity (EC), mineral composition, pH, zeta potential, cation exchange capacity (CEC) and anion exchange capacity (AEC)) are affected by the feedstock type as well as temperature of pyrolysis and the P sorption capacity is highly dependent on these properties. The P removal is also affected by the water matrix chemistry, such as the presence of competing ions and bulk pH conditions. Finally, several recommendations for future research have been proposed to facilitate and enhance the environmental efficiency of biochar application.

Nitrate removal from aqueous solutions by adsorption onto hydrogel-rice husk biochar composite

In the present study, we investigated the performance of hydrogel-rice husk biochar composites, as low-cost, alternative, and biocompatible adsorbents for separating nitrate ions from aqueous solutions. Hydrogel-biochar composite was synthesized at dosages of 2.5%, 3.6%, 4.8%, and 9.6% weight ratios of biochar. The composite was characterized by several common methods including FTIR, SEM, TEM, TGA, and DSC. In addition, the effect of contact time, initial concentration of nitrate ions, and solution pH were considered. The maximum removal of nitrate was about 34.3% at acidic pH (pH = 3) using 0.02 g of adsorbent in 25 ml of nitrate solution with the initial concentration (20 mg/L) and temperature of 25°C for 60 min. Based on the findings, 5% biochar in the composite was the optimal dosage. Adsorption kinetic study revealed that this process followed the first-order kinetic model. The experimental equilibrium adsorption data were tested by the Temkin isotherm model with R²  > 0.97. Based on the thermodynamic studies, the adsorption process was endothermic and spontaneous. Overall, the results suggested that the obtained composite can be specifically employed for removal of contaminations from aqueous solutions. PRACTITIONER POINTS: Hydrogel-biochar composite provides a biocompatible and cost-effective adsorbent. Hydrogel-biochar composite was applied to eliminate nitrate from aqueous solutions. Nitrate removal increased in the synthesized composite upon elevation of the weight ratio of biochar to 0.2 g.