Long-term Results of a First-Generation Annealed Highly Cross-Linked Polyethylene in Young, Active Patients

Wear of Third-Generation Cross-Linked Polyethylene in Primary Total Hip Arthroplasty: A 10-Year Analysis

BACKGROUND

Sequential modifications to the manufacturing process of highly cross-linked polyethylene (HXLPE) have improved the wear resistance and implant survival of these liners in total hip arthroplasty (THA). However, no study has examined the long-term (mean 10 year) wear rates and clinical outcomes of third-generation HXLPE in THA. The aim of our study was to report the longest-to-date analysis of wear rates and clinical outcomes of a third-generation HXLPE liner.

METHODS

A series of 133 THAs using a specific HXLPE acetabular liner were retrospectively evaluated. Linear and volumetric wear rates were determined using a validated radiographic technique and clinical outcomes were analyzed. Multivariate analyses were performed to determine risk factors for accelerated wear.

RESULTS

At a mean follow-up of 10.4 years (range, 8 to 13.4), the mean linear wear rate was 0.0172 mm/year and the mean volumetric wear rate was 16.99 mm3/year. There were no instances of osteolysis or mechanical failures at any time point and there was a 100% acetabular component survival rate. Younger age and use of offset liners were independent risk factors for increased wear (P < .01 for both).

CONCLUSIONS

Our series of a third-generation HXLPE demonstrated very low wear rates and excellent implant survival at a mean of 10.4 years following primary THA. Future comparative studies at the 15- and 20-year follow-up timepoints are necessary to determine if such findings translate to true improvements in the tribological properties and longevity of these liners when compared to previous generations of HXLPE liners.

Trends in Complications and Outcomes in Patients Aged 65 Years and Younger Undergoing Total Hip Arthroplasty: Data From the American Joint Replacement Registry

This study sought to determine common complications and the rates of readmission and revision in total hip arthroplasty patients younger than 65 years. Using the American Joint Replacement Registry, we conducted a retrospective review of all THAs in patients aged 18 to 65 years from 2012 to 2020. We excluded patients aged older than 65 years, revisions, oncologic etiology, conversion from prior surgery, and nonelective cases. Primary outcomes included cumulative revision rate, 90-day readmission rate, and reason for revision. The Kaplan-Meier method and univariate analysis were used. Five thousand one hundred fifty-three patients were included. The average age was 56.7 years (SD 7.8 years), 51% were female, 85% were White, and 89% had a Charlson Comorbidity Index of 0 (1 = 7%, >2 = 4%). The mean follow-up was 39.57 months. Fifty-three patients (1.0%) underwent revision. Seventy-four patients (1.4%) were readmitted within 90 days. Revision was more common in Black patients (P = 0.023). Survivorship was 99% (95% confidence interval, 98.7 to 99.3) and 99% (95% confidence interval, 98.5 to 99.3) at 5 and 8 years, respectively. Infection (21%), instability (15%), periprosthetic fracture (15%), and aseptic loosening (9%) were the most common indications for revision. Total hip arthroplasty performed in young and presumed active patients had a 99% survivorship at 8 years. A long-term follow-up is needed to evaluate survival trends in this growing population.

Risk Factors for Significant Radiolucent Line Development in a Fully Coated Hydroxyapatite Stem

BACKGROUND

The risk factors for and clinical impact of radiolucent lines (RLLs) in cementless total hip arthroplasty remain contentious. The aim of this work was to describe a method of classification that has clinical significance and to identify risk factors.

METHODS

A cohort of 288 subjects with unrevised Corail stems (DePuy Synthes, Warsaw, IN) were reviewed with radiographs and Oxford Hip Scores at 10 years. Based on clinical experience, three groups were defined; those with no RLLs (NoRLLs), those considered to have benign RLLs (BenRLLs), and those considered to have significant RLLs (SigRLLs). SigRLLs were then compared to BenRLLs and NoRLLs to determine the validity of this classification.

RESULTS

One hundred and nine (37.8%) had NoRLLs, 111 (38.5%) had BenRLLs, and 68 (23.6%) had SigRLLs. No significant difference apart from gender was noted between the occurrence of BenRLLs and NoRLLs after multinomial regression analysis, consequently the NoRLLs and BenRLLs groups were combined (NoSigRLLs) and compared to SigRLLs. Non-cross-linked polyethylene (odds ratio = 4.6, P < .001), collarless stem design (odds ratio = 9.4, P < .001), undersizing (odds ratio = 1.2, P = .028), and male sex (odds ratio = 2.1, P = .008) were risk factors for SigRLLs. Regression analysis also revealed that increasing age at operation decreased the likelihood of SigRLLs (P < .001). Patients with SigRLLs had significantly higher pain scores (P = .005) although overall Oxford Hip Scores were not significantly different (P = .364).

CONCLUSION

The definition of SigRLLs proposed in this study was significantly associated with that of non-cross-linked polyethylene, absence of a collar, undersizing, and higher pain scores.

Incidence of Osteolysis and Aseptic Loosening Following Metal-on-Highly Cross-Linked Polyethylene Hip Arthroplasty: A Systematic Review of Studies with Up to 15-Year Follow-up

BACKGROUND

This study compared the incidence of osteolysis, aseptic loosening, and revision following use of highly cross-linked polyethylene (HXLPE) or conventional polyethylene (CPE) at medium to long-term (>5 to 15 years) follow-up in primary total hip arthroplasty (THA). Incidences were quantified and compared with regard to age and method of implant fixation.

METHODS

Using the PRISMA (Preferred Reporting Items for Systematic reviews and Meta-Analyses) guidelines, 12 randomized controlled trials and 18 cohort studies were investigated for evidence-based outcomes following HXPLE and CPE use in 2,539 hips over a 5 to 15-year follow-up.

RESULTS

Lower rates of osteolysis, aseptic loosening, and implant revision were reported following use of HXLPE liners. Osteolysis was reduced from 25.4% with CPE to 4.05% with HXLPE in young patients, and from 29.7% to 6.6% in the older patient cohort. Similarities in osteolysis rates were observed when cemented (24.9% for CPE and 6.5% for HXLPE) and uncemented components (32.8% for CPE and 7.1% for HXLPE) were compared. No clear advantage in the type of HXLPE used was observed.

CONCLUSIONS

Over a follow-up period of up to 15 years, when compared with CPE, use of HXLPE liners reduced the incidence of osteolysis, aseptic loosening, and implant revision, regardless of the fixation method and including in younger and potentially more active patients.

LEVEL OF EVIDENCE

Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Estudo biomecânico comparativo do desgaste do polietileno reticulado com cabeças femorais cerâmicas de 36 mm e com cabeças metálicas de 32 mm

Objetivo: O objetivo do presente estudo foi comparar, in vitro, a taxa de desgaste do polietileno de alto peso molecular reticulado acoplado a cabeças cerâmicas de 36 mm de diâmetro e acoplado a cabeças metálicas de 32 mm de diâmetro.

Métodos: Foram realizados ensaios biomecânicos em simulador de desgaste para os pares tribológicos cerâmica-poli (36 mm) e metal-poli (32 mm) a fim de verificar a taxa de desgaste após em 15 × 106 ciclos.

Resultados: Na comparação entre as medidas de taxa de desgaste dos conjuntos com cabeças metálicas (média:14,12 mg/MC) e cerâmicas (média:7,46 mg/MC) houve diferença estatitsticamente significativa (p = 0,0005).

Conclusão: O presente estudo demonstrou menor taxa de desgaste em conjuntos protéticos que utilizaram o par tribológico cerâmica-polietileno reticulado de 36 mm em comparação aos conjuntos com metal-polietileno reticulado de 32 mm. Tal achado demonstra a eficácia do par tribológico cerâmica-poli, mesmo com a utilização de cabeças de grande diâmetro.

Third-Generation Medium Cross-Linked Polyethylene Demonstrates Very Low Wear in Total Hip Arthroplasty

Background

Cross-linked polyethylene (XLPE) liners have shown lower wear rates than conventional polyethylene liners in total hip arthroplasty. The primary aim of our study was to report our most recent analysis of wear rates and clinical outcomes of a third-generation XLPE liner. Secondary aims were to investigate the rate of adverse events related to mechanical failure or oxidation of this liner.

Methods

A series of 266 total hip arthroplasties using a specific XLPE liner were retrospectively reviewed. Radiographs were examined to determine linear and volumetric wear rates and presence of osteolysis. Clinical outcomes, revision rates, mechanical failures, and risk factors for accelerated polyethylene wear were additionally investigated.

Results

The mean age at the time of surgery was 65.8 years and the mean follow-up was 5.5 years. The mean linear wear rate was 0.003 mm/year and the mean volumetric wear rate was 0.42 mm³/year, and there was no evidence of osteolysis. Harris hip scores increased from 50.9 preoperatively to 96.0 at the latest follow-up. The revision rate was 0.4%, with no liner rim fractures and no liner dissociations/loosenings. Femoral head material, head size, age, body mass index, and time since implantation had no effect on wear rates.

Conclusion

Wear rates for this third-generation XLPE liner were low at mid-term follow-up, and no adverse sequelae of oxidation or deleterious mechanical properties were observed. This remained true regardless of femoral head size and material or patient age and body mass index. Further analysis will be necessary to ensure continued wear resistance, oxidative stability, and mechanical strength at long-term follow-up.

Observed effect of femoral component undersizing and a collarless design in the development of radiolucent lines in cementless total hip arthroplasty

Background

The objective of this study was to determine the prevalence of radiolucent lines (RLLs) around the femoral component in a cohort of patients who underwent well-functioning cementless total hip arthroplasty (THA).

Methods

A cohort of unrevised Corail (DePuy Synthes, Raynham, MA) femoral components (n = 636) were analyzed at a median follow-up of 6.0 years (interquartile range: 5.2-6.8) with the Oxford Hip Score (OHS) and radiographs. Two independent observers assessed the radiographs for the presence of RLLs.

Results

The overall prevalence of RLLs in zone 7 was 13% (83/636). Patients with RLLs in zone 7 had an average OHS of 40.3 (15-48), and those who did not have RLLs in zone 7 had an average OHS of 38 (6-48), P = .07. Both groups had an average pain score of 1.6 out of 5, P = .5. The prevalence of RLLs in zone 7 was much less in the collared femoral components (2.6% prevalence) than in the collarless components (23.6% prevalence), but there was heterogeneity between these 2 groups preventing comparison. Logistic regression analysis of only the collarless components identified undersizing as the only predictive (odds ratio = 2.6) factor for RLL development in zone 7.

Conclusions

Undersizing the Corail stem is strongly predictive of developing RLLs in zone 7. Preoperative templating for the appropriate size is critical. We observed more RLLs in zone 7 with the collarless design Corail, but a comparison study with the same bearing couple is needed to investigate this further.

Low failure rate at short term for 40 mm heads and second generation triple annealed HCLPE liners in hybrid hip replacements

INTRODUCTION

40 mm large diameter heads offer the advantages of lesser dislocation rates and better stability while highly cross linked polyethylene have lower wear rates than ultra high molecular weight polyethylene. Studies of the survivorship of 40 mm heads in hybrid hip replacements with Exeter stem and second generation highly cross linked polyethylene are limited. The purpose of the study is to report the short term of survivorship of the large diameter heads (40 mm) with Exeter stem with the secondary aim being the survival analysis of the thinnest second generation highly cross linked polyethylene.

METHODS

Retrospective case series of survivorship of patients with hybrid hip replacements of Exeter stems with 40 mm heads articulating with second generation triple annealed highly cross linked polyethylene liner on a uncemented acetabular shell was performed. As a subset, survival of thinnest second generation highly cross linked polyethylene survival (3.8 mm) at short term was assessed. Survival of the implants was confirmed from the hospital records and National joint registry as of 2015. Revision for any cause was taken as end point.

RESULTS

324 hybrid hip replacements with 40 mm heads had been performed for primary hip osteoarthritis. Of the 324 hip replacements, 154 hip replacements had thinnest second generation highly cross linked polyethylene (3.8 mm). Two patients had revision of components, one for periprosthetic fracture and one for deep infection. Mean age of the patients was 70.5 years (range 42-88 years, median 71, SD 8.3 years). None of the patients had revision due to trunion wear or loosening of components. The overall 5-year implant survival probability of hips with 40 mm heads was 99.4% (95% CI 98 to 100%) while the subset group of hip replacements with thinnest second generation highly cross linked polyethylene (3.8 mm) had 5-year implant survival probability of 99.3% (95% CI 97.1 to 100%).

CONCLUSION

Short term survivorship does not show significant evidence of early failure or higher rate of revision in our series of hybrid hip replacements with large diameter heads and second generation triple annealed highly cross linked polyethylene. Dislocation rate at the short term is none. Results from this series have to be carefully interpreted due to the relatively short follow up but so far results are encouraging. Long term follow up is required to conclude whether there is early or higher rate of failure. It is our intention to follow up this cohort and further publish our results at longer term.

Cross-Linked Polyethylene for Total Hip Arthroplasty Markedly Reduces Revision Surgery at 16 Years

BACKGROUND

Total hip arthroplasty (THA) is an effective operation for the management of end-stage hip osteoarthritis, but long-term success can be limited by wear of the polyethylene bearing surface. Cross-linking conventional polyethylene has resulted in lower wear rates and a reduction in bone lysis in both laboratory and clinical studies. The aim of this study was to compare the rates of revision between cross-linked polyethylene (XLPE) and conventional non-cross-linked polyethylene (CPE) at 16 years after THAs performed for the treatment of osteoarthritis.

METHODS

We performed an observational study of data, from a national registry, on all patients who underwent THA for osteoarthritis in Australia from 1999 through December 31, 2016. The outcomes of THAs performed with CPE were compared with those of THAs performed with XLPE, along with an analysis of the effect of age, sex, femoral head size, the method of acetabular and femoral component fixation, and the reasons and types of revision. The principal outcome measure was the time to the first revision, determined using Kaplan-Meier estimates of survivorship.

RESULTS

CPE was used in 41,171 procedures, and XLPE was used in 199,131. The mean ages of the men and women treated with CPE were 70.0 years (standard deviation [SD] = 9.9 years) and 72.5 years (SD = 9.7 years), respectively, whereas the men and women who received XLPE were slightly younger (mean age, 68.6 years [SD = 10.3 years] and 70.7 years [SD = 9.9 years], respectively. XLPE was associated with a lower rate of revision than CPE at 6 months, and this difference became more apparent with time. The 16-year cumulative percentage of revisions of the primary THAs was 11.7% (95% confidence interval [CI] = 11.1% to 12.3%]) in the CPE group and 6.2% (95% CI = 5.7% to 6.7%) in the XLPE group. The hazard ratio at 9 years was 3.02 (p = 0.001).

CONCLUSIONS

The use of XLPE has resulted in a significant reduction in the rate of revision at 16 years following THA for osteoarthritis. This evidence suggests that the longevity of THA is likely to be improved, which may enable younger patients to undergo surgery, confident of a reduced need for revision in the long term.

LEVEL OF EVIDENCE

Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

Wear Analysis of Highly Cross-Linked Polyethylene in Young and Active Patients at Average Fourteen Years: A Concise Follow-Up of a Previous Report

BACKGROUND

Concerns persist regarding the oxidative stability of annealed highly cross-linked polyethylene (HXLPE) and hence its wear performance especially long term in young and active patients. The purpose of this study is to assess the wear rates and clinical outcomes of a first-generation annealed HXLPE.

METHODS

Forty-six patients (57 hips) with noncemented fixation, a mean age of 53 years, and a mean University of California Los Angeles activity score of 8 underwent primary total hip arthroplasty. A 28-mm femoral head against HXLPE liner was used in all cases. Linear wear rates were measured by 2 independent observers. Radiological and clinical assessments were recorded.

RESULTS

At a mean of 14 years (range 10-17), the wear rate was 0.03 mm/y (SD ±0.02). There were no revisions for wear-related complications. Using revision for wear-related complications as an endpoint, the survivorship was 100% and we observed no osteolysis. Western Ontario and McMaster Universities Osteoarthritis Index, patient administered questionnaire, and Hospital for Special Surgery hip scores were 91/100, 5/100, and 37/40 respectively.

CONCLUSION

This study confirms that a first-generation annealed HXLPE shows excellent wear and clinical results at 10-17 years in young and active patients. Oxidative degradation of an annealed HXLPE does not adversely affect wear and shows no other wear-related complications.

Hip fusion takedown to a total hip arthroplasty-is it worth it? A systematic review

INTRODUCTION

Patients with surgically or spontaneously fused hips are often dissatisfied with their overall function and the debilitating effect on adjacent joints. Therefore, in properly selected patients, hip fusion-takedown and conversion to total hip arthroplasty (THA) can result in improved function and decreased pain. We aimed to (1) evaluate the indications for conversion, (2) evaluate the clinical outcomes, (3) analyze the overall complications, and (4) identify the overall satisfaction following the procedure.

METHODS

A systematic and comprehensive literature search was performed to analyze studies evaluating conversion of hip fusion to THA. After reviewing 3,882 studies, 27 total studies (1,104 hips) met our inclusion/exclusion criteria and were included in our final analysis. A weighted mean of rates was determined for each complication, including infection, instability, loosening, nerve-related, abductor-related, venous thrombotic event, and revision.

RESULTS

The study population consisted of 53.2% male and 46.8% female subjects. The mean age at time of conversion was 52 years (range 36-65 years), the mean time until follow-up was 9.2 years (range 2.5-17.3), and the mean duration of arthrodesis was 27.7 years (range 11-40.2). As measured by Harris Hip Score, overall clinical outcomes improved from 58.1 points (range 42.4-70 points) pre-operatively to 80.0 (range 62-93.5) post-operatively. The specific complication rates were 5.3% (range 0-43.6%) for infection, 2.6% (range 0-15.4%) for instability, 6.2% (range 0-17.2%) for loosening, 4.7% (range 0-13%) for nerve-related complications, 13.1% (range 0-87%) for abductor-related complications, and 1.2% (range 0-13%) for venous thrombotic events. The revision rate was 12.0% (range 0-43.6%).

CONCLUSION

Takedown of a fused-hip can be a challenging procedure. Although patients can benefit functionally, both patients and surgeons need to be aware of the complications and increased risk of further revision procedures, which should be an important part of the pre-operative discussion.

Wear products of total hip arthroplasty: The case of polyethylene

Among the bearing surfaces involved in a total hip arthroplasty, ultra-high molecular weight polyethylene (UHMWPE) is the weak link. It is submitted to the friction of a harder bearing, producing wear particles, which, in turn, initiate an inflammatory reaction ultimately leading to osteolysis. This kind of bone deterioration sometimes turns out to an aggressive granuloma and may provoke implant loosening. Wear resistance of UHMWPE depends on its molecular weight and crystallinity. Some steps of the manufacturing process were improved to optimize its tribological properties and to slow down degradation resulting from mechanical (abrasion) and chemical (oxidation) phenomena. Its preparation and conservation must be performed in an inert atmosphere, i.e. without ambient oxygen. Its resistance to abrasion depends on its cross-linking degree. Its cross-linking rate was observed to increase proportionally to the irradiation doses, improving its wear resistance. However, its mechanical properties are impaired and moreover, it becomes oxidation sensitive. It is therefore necessary to submit it to a thermal treatment to eliminate free radicals that were produced during irradiation. More recently impregnation by vitamin E, a powerful anti-oxidant product, was proposed to preserve the polymer from in vivo oxidation while maintaining its mechanical properties. We raised the hypothesis that last-generation UHMWPE could offer the same wear resistance as the most performing bearings (ceramic-on-ceramic). Recent clinical results confirm the tribological performance of highly crosslinked UHMWPE in vivo. However, it remains to be seen whether this excellent wear resistance would persist under eccentric load such as edge loading, and if, in the long run, this kind of bearing proves capable of reducing the risk of osteolysis in young and active patients.