Effect of Downsized Screw Selection on Bone Healing and Postoperative Complications in Volar Plating of Distal Radius Fractures

Extensor pollicis longus tendon penetration by a screw post-distal radius fracture plating in a young woman: A case report

INTRODUCTION

Due to its ability to provide stable fixation and permit early mobilization, volar plating has become the recommended technique for the surgical stabilization of distal radius fractures. The extensor pollicis longus (EPL) tendon may be injured or ruptured as a result of undetected screw penetration or drill plunging. During surgery, it is critical to detect any potential screw penetration so that it can be corrected.

CASE PRESENTATION

A 32-year-old woman presented six weeks post-distal radius plating with an inability to extend her left thumb. Clinical examination revealed loss of extension at the interphalangeal joint, stiff wrist, tender point over the dorsal aspect of the wrist, and an intact sensory nerve function.

DISCUSSION

Dynamic ultrasound and magnetic resonance imaging (MRI) both revealed no evidence of tendon rupture or EPL tendon movement. X-rays revealed the distal epiphyseal screws penetrating the far cortex. Intraoperatively, the EPL tendon was found to be impinged by a screw. The tendon was released, tenolysis was performed, and the distal screws were shortened.

CONCLUSION

In order to assess screw penetration into the far cortex, volar plating for distal radius fractures should be performed using intraoperative imaging views such as lateral, 45-degree supination, 45-degree pronation, dorsal tangential, and skyline views. Timely interventions after distal radius fracture fixation preserve tendon function, and early detection of tendon compromise is essential to preventing additional damage.

CT-Based Micromotion Analysis After Locking Plate Fixation of AO Type C Distal Radius Fractures

Background

Volar locking plate fixation (VLPF) is the most common method for operative fixation of distal radius fractures (DRF). The dorsal ulnar corner (DUC) can be difficult to stabilize as the fragment is small and not exposed when using the volar approach. The purpose of this study was to study fracture fragment migration after VLPF of AO type C DRF, using a volume registration technique of paired CT scans with special focus on the DUC fragment.

Materials and Methods

This pilot study included ten patients with AO type C DRF, all operated with VLPF. The primary outcome was radiographic outcome. Postoperative and 1-year scans were compared and analyzed. Fragment migration was assessed with CT-based micromotion analysis (CTMA), a software technique used for volume registration of paired CT scans.

Results

All plates were stable over time. Two patients showed signs of screw movement (0.2-0.35 mm and 0.35- > 1 mm respectively). Postoperative reduction was maintained, and there was no fragment migration at the 1-year follow-up except for one case with increased dorsal tilt. The DUC fragment was found in 8/10 cases, fixated in 7/8 cases, and not dislocated in any case at the 1-year follow-up.

Conclusion

The CTMA results indicate that variable-angle VLPF after AO type C DRF can yield and maintain a highly stable reduction of the fracture fragments. The DUC fragment remained stable regardless of the number of screws through the fragment. CT volume registration can be a valuable tool in the detailed assessment of fracture fragment migration following volar plate fixation of DRFs.

Extensor Tendon Injury After Volar Locking Plating for Distal Radius Fractures: A Systematic Review

Distal radius fractures are common orthopedic injuries. Treatment has varied historically, but volar locking plating currently predominates. Although flexor tendon injury is a well-studied complication of this operation, extensor tendon injury is less well studied. The purpose of this review is to search the literature and present the epidemiology, presentation, and treatment of this complication. The Cochrane, EMBASE, PubMed, and SCOPUS databases were searched for the terms "volar" + "radius" + ("plate" OR "plating") + "extensor." Ninety final studies were included for analysis in this review. The incidence of extensor tendon rupture varies from 0% to 12.5%; the extensor pollicis longus is most commonly ruptured. The presentation and management of extensor tendon injury after injury, intraoperatively, and postoperatively are summarized. Radiographic views are described to detect screw prominence and minimize intraoperative risk. Extensor tendon injury after volar locking plate for distal radius fractures is an uncommon injury with several risk factors including dorsal screw prominence and fracture fragments. Removal of hardware and tendon transfers or reconstruction may be necessary to prevent loss of extensor mechanism.