Evaluation of Corneal Flap Dimensions and Cut Quality Using the Automated Corneal Shaper Microkeratome

Evaluation of Human Corneal Lenticule Quality After SMILE With Different Cap Thicknesses Using Scanning Electron Microscopy

PURPOSE

To evaluate the surface characteristics of lenticules created by small-incision lenticule extraction (SMILE) with different cap thicknesses.

METHODS

This prospective study included 20 consecutive patients who underwent bilateral SMILE. Surface regularity of the extracted corneal lenticule was analyzed using scanning electron microscopy (SEM) combined with 2 methods: qualitative and quantitative regularity. Qualitative regularity of SEM images was graded by masked observers using an established scoring system. Quantitative regularity of SEM images was assessed by counting the total number and areas of tissue bridges using Image-Pro Plus software. Four different cap thickness of 120, 130, 140, and 150 μm were compared. Refractive outcomes of patients were measured at baseline and 1 month after surgery.

RESULTS

As 10 specimens were not analyzable, only 30 eyes were included. Postoperatively, all eyes had postoperative uncorrected distance visual acuity of 20/20 or better; 43% had an unchanged corrected distance visual acuity; 43% gained 1 line; 10% lost 1 line. Ultrastructurally, surface irregularity was primarily caused by tissue bridges. The average surface regularity score obtained was 10.87 ± 2.40 for 120 μm, 10.78 ± 2.60 for 130 μm, 8.76 ± 2.16 for 140 μm, and 8.70 ± 2.66 for 150 μm (P < 0.001). The total number and areas of tissue bridges of 120 to 130 μm were significantly less than 140 to 150 μm (P < 0.05). Surface regularity decreased as cap thickness increased (P < 0.05).

CONCLUSIONS

There is smoother appearance of the lenticular surface as seen through SEM when a thin cap is created compared with a thick cap qualitatively and quantitatively.

Flap-induced astigmatism in eyes with sphere myopia correction: Superior hinge using a rotating microkeratome versus nasal hinge using a linear microkeratome

PURPOSE

To compare the effect of a rotating microkeratome (M2) and a linear microkeratome (SBK) on the change in the astigmatic component in eyes with preoperative plano refractive cylinder.

SETTING

University Medical Centre Hamburg-Eppendorf, Hamburg, Germany.

DESIGN

Retrospective case series.

METHODS

An Allegretto excimer laser was used to perform laser ablation in myopic eyes of consecutive patients. The laser in situ keratomileusis (LASIK) procedure included mechanical flap preparation using a microkeratome, either a linear type with a single-use 90 μm head to create a nasal hinge or a rotating type with a single-use 90 μm head to create a superior hinge. The Alpins vector method was applied to describe the effects of LASIK on postoperative refractive cylinder.

RESULTS

The study evaluated 1045 eyes of 852 patients. Although the mean overall efficacy and safety indices indicate the procedure was highly precise, safe, and efficient, there were statistically significant differences in surgically induced astigmatism (SIA) between the microkeratomes (P = .002). The postoperative refractive cylinder (ie, SIA) was 0.75 diopter (D) or more in 116 eyes (11.1%), 44 (12.8%) of 344 linear cases and 72 (10.3%) of 701 rotating cases. Independent of the type of microkeratome used, the SIA was slightly higher in eyes treated first; the mean magnitude of the induced astigmatism was 0.35 D.

CONCLUSIONS

In approximately 10% of eyes with preoperative plano refractive myopia, the astigmatic component tended to be overcorrected. Nevertheless, independent of the type of microkeratome, the maximum mean magnitude of refractive cylinder documented was 0.35 D.

FINANCIAL DISCLOSURE

No author has a financial or proprietary interest in any material or method mentioned.

Randomized, contralateral eye study to evaluate the effect of standard and inverted side-cut angle on corneal biomechanical properties during femtosecond laser-assisted in situ keratomileusis

PURPOSE

To evaluate the effect of side-cut angle profile on corneal biomechanical properties after femtosecond laser in situ keratomileusis (FS-LASIK).

METHODS

Ninety-six myopic eyes of 48 patients underwent FS-LASIK. One eye of each patient was randomized to flap creation with a side-cut angle of 115°. The fellow eye flap side-cut angle was adjusted to 70°. Mean absolute error of flap diameter and mean change in Goldmann-correlated intra-ocular pressure (IOPg), corneal-compensated IOP (IOPcc), corneal hysteresis (CH), corneal resistance factor (CRF), p1 area, p2 area, p1 area 1 and p2 area 1 were compared between both groups.

RESULTS

Overall, the mean IOPg and CRF showed significant reduction at the end of 1 and 3 months, as well as between 1 and 3 months postoperatively (p ≤ 0.03). The mean IOPcc and CH showed significant reduction (p < 0.001) at the end of 3 months postoperatively. The parameters p1 area, p2 area, p1 area 1 and p2 area 1 changed significantly at the end of 1 and 3 months postoperatively (p < 0.001). There was no significant difference between both groups with regards to the mean change of IOPg, IOPcc, CH, CRF, p1 area, and p1 area 1. In 115° group, the mean absolute error in flap diameter was greater compared with 70° group (p = 0.014).

CONCLUSIONS

The stability of IOP and corneal biomechanical properties were not enhanced in FS-LASIK flaps with an inverted side-cut angle. The size of corneal flap created with 70° side-cut angle was more accurate compared with 115° side-cut angle.

Comparison of the predictability, uniformity and stability of a laser in situ keratomileusis corneal flap created with a VisuMax femtosecond laser or a Moria microkeratome

This prospective study compared the predictability, uniformity and stability of laser in situ keratomileusis corneal flap thickness created by a femtosecond laser or a classic microkeratome. Twenty-five femtosecond laser (VisuMax, Carl Zeiss Meditec) flaps and 38 microkeratome (Moria M3) flaps were measured using anterior segment optical coherence tomography at 1 week, 1 month and 6 months postoperatively. Flap thickness at seven points on each of the four meridians was calculated. At 6 months, VisuMax flaps showed better prediction than Moria flaps for central flap thickness. The standard deviation within individual flaps was smaller for VisuMax flaps and their index of symmetry was better. The mean thicknesses among the four eccentricities in the VisuMax flaps were the same, while Moria flaps were thicker at the 3-mm radius compared with the centre. The VisuMax femtosecond laser created corneal flaps with better predictability and uniformity, and similar reproducibility and stability, compared with the microkeratome.

Intraoperative flap complications in laser in situ keratomileusis with two types of microkeratomes

PURPOSE

To determine the incidence and types of intraoperative flap complications in laser in situ keratomileusis (LASIK) encountered with the Hansatome microkeratome and the Moria microkeratome.

METHODS

In this retrospective case series, all patients with intraoperative flap complications who were treated between June 1999 and July 2008 at the Eye Consultants Center in Riyadh, Saudi Arabia, were identified and reviewed.

RESULTS

Of the 4352 subjects who underwent bilateral primary LASIK procedure, intraoperative microkeratome complications were detected in 89 eyes of 83 patients. The overall incidence of flap complications was 89/8704 (1.00%): incomplete flaps occurred in 53 eyes (0.60%), followed by buttonhole flaps in 17 eyes (0.19%), free complete flaps in 10 eyes (0.11%), free partial flaps in 6 eyes (0.07%), sluffed epithelium in 2 eyes (0.023%), and a splitted flap (vertical flap cut) in 1 eye (0.01%). The incidence rates of intraoperative flap complications with the Hansatome microkeratome and the Moria microkeratome were 1.21% (41/3378) and 0.90% (48/5326), respectively (P = 0.19). There was a statistically significant difference between the two microkeratomes with regard to the incidence of buttonhole flaps: 0.33% (11/3378) for the Hansatome microkeratome versus 0.11% (6/5326) for the Moria microkeratome (P = 0.04).

CONCLUSION

Generally, the incidence rates of intraoperative flap complications with the Hansatome microkeratome and the Moria microkeratome were similar. However, buttonhole flaps occurred more often with the Hansatome microkeratome (a type of microkeratome that produces larger flaps). The commonest complication encountered was the incomplete flap, followed by the buttonhole flap and free flap.

Comparison of the changes in corneal biomechanical properties after photorefractive keratectomy and laser in situ keratomileusis

PURPOSE

To compare the postoperative biomechanical properties of the cornea after photorefractive keratectomy (PRK) and after laser in situ keratomileusis (LASIK) in eyes with myopia.

METHODS

We retrospectively examined 27 eyes of 16 patients undergoing PRK and 31 eyes of 16 patients undergoing LASIK for the correction of myopia. Corneal hysteresis (CH) and corneal resistance factor (CRF) were measured with Ocular Response Analyzer before and 3 months after surgery. We also investigated the relationship between these biomechanical changes and the amount of myopic correction.

RESULTS

The CH was decreased significantly from 10.8 +/- 1.3 (mean +/- SD) mmHg to 9.2 +/- 1.6 mmHg after PRK (P < 0.001), and from 10.8 +/- 1.4 mmHg to 8.6 +/- 0.9 mmHg after LASIK (P < 0.001). The CRF was also decreased significantly, from 10.3 +/- 1.5 mmHg to 8.4 +/- 1.8 mmHg after PRK (P < 0.001), and from 10.3 +/- 1.5 mmHg to 7.7 +/- 1.3 mmHg after LASIK (P < 0.001). The amount of decrease in CH and CRF was significantly larger after LASIK than after PRK (P = 0.04). There was a significant correlation between the amount of myopic correction and changes in biomechanical properties after PRK (r = -0.61, P < 0.01 for CH, r = -0.41, P < 0.05 for CRF) and LASIK (r = -0.37, P < 0.05 for CH, r = -0.45, P < 0.05 for CRF).

CONCLUSIONS

Both PRK and LASIK can affect the biomechanical strength of the cornea depending on the amount of myopic correction. The amount of biomechanical changes is larger after LASIK than after PRK. From a biomechanical viewpoint, PRK may be a less invasive surgical approach for the correction of myopia than LASIK.

Customizing the Amadeus II microkeratome: evaluation of cut quality with various settings using electron microscopy

PURPOSE

To evaluate the cut quality of keratectomy specimens created with the new Amadeus II microkeratome (SIS, Ziemer Ophthalmic, Port, Switzerland) using scanning electron microscopy (SEM). Methods. Corneal cuts were performed in 24 freshly enucleated porcine eyes using the Amadeus II microkeratome with combinations of cutting-head depth, oscillation rate, head-advance speed, and reuse of the blade. For the cutting trials, a 140-microm and 160-microm cutting head with three oscillation rates of 8,000, 10,000, and 13,000 rpm and two head-advance speed rates of 1.5 and 3.5 mm/s were chosen. In each setting, the blade was reused for a second time. All eyes were included, resulting in 4 groups with 6 eyes for each configuration. The surface and edge of the corneal cut was examined using SEM.

RESULTS

At fixed oscillation rates, an increase in head-advance speed led to lower quality cuts, higher surface roughness, and irregular cut edges for both cutting heads (140 microm/160 microm), especially when using the blade for a second time. At fixed head-advance speeds an increase in oscillation rates improved the cut quality for both cutting heads (140 microm/160 microm). This results in smoother surface characteristics and more regular cut edges, especially when using the blade for the first time.

CONCLUSIONS

Using the Amadeus II microkeratome for laser in situ keratomileusis procedures, the optimum oscillation rate, the optimum head-advance speed, and a single use of the blade will produce a very smooth and regular surface and cut edge for safe, comfortable, and improved customized refractive surgery.

Incidence, management, and visual outcomes of buttonholed laser in situ keratomileusis flaps

PURPOSE

To describe the incidence, management, and visual outcomes of buttonholed laser in situ keratomileusis (LASIK) flaps.

SETTING

Private practice, Riyadh, Saudi Arabia.

METHODS

This retrospective review identified eyes that developed buttonholed flaps during LASIK. Preoperative, intraoperative, and postoperative data were obtained to identify factors predictive of this complication.

RESULTS

Of 4250 primary LASIK procedures, 17 eyes (0.4%) with buttonholed flaps were identified. Buttonholes occurred with the Hansatome microkeratome in 64.7% of eyes and with the Moria microkeratome in 35.3% of eyes, the incidence of buttonholed flaps was 0.62% and 0.19%, respectively (P = .03). Laser ablation was performed at the same time as buttonhole formation in 8 eyes (47.1%) and was aborted in the other eyes. Retreatment was performed in 10 eyes (58.8%); of retreated eyes, 6 had repeat LASIK and 3 had surface ablation. The final spherical equivalent refraction was -0.38 diopter +/- 0.79 (SD). Two eyes had a final loss of more than 2 lines of best corrected visual acuity (BCVA). The mean loss of BCVA lines was 0.72 in eyes that had complete LASIK, 0.62 in eyes that had aborted LASIK followed by retreatment with repeat LASIK, and 0.80 in eyes that had aborted LASIK followed by retreatment with surface ablation.

CONCLUSIONS

Buttonholed flaps occurred more frequently in the second of 2 consecutively treated eyes. Microkeratomes that produce a larger diameter flap were more likely to produce flap buttonholes. The least loss of BCVA was achieved when LASIK was aborted and then repeated after refractive stability.

Comparison of corneal flap thickness between primary eyes and fellow eyes using the Zyoptix XP microkeratome

PURPOSE

To evaluate corneal flap thickness created in myopic laser in situ keratomileusis (LASIK) using the Zyoptix XP 120 microkeratome (Bausch & Lomb).

SETTING

University-based eye clinic.

METHODS

Corneal thickness was measured preoperatively and intraoperatively after flap creation in 62 consecutive patients (124 eyes) who had LASIK for the correction of myopia. Corneal flap thickness was calculated by subtracting stromal bed thickness from total corneal thickness. In each patient, both corneas (right followed by left) were cut by 1 the same Zyoptix XP 120 microkeratome blade at the same session.

RESULTS

The mean actual flap thickness was 115.34 microm +/- 16.34 (SD) in right eyes and 104.55 +/- 14.34 mum in left eyes. The mean actual flap thickness in right eyes was not statistically significantly different from the 120 microm proposed by the manufacturer (P = .142); however, the mean actual flap thickness in left eyes was statistically significantly different from the 120 microm (P<.001). The mean flap thickness in the second eye was also statistically significantly thinner than in the first eye (P<.001).

CONCLUSIONS

The corneal flaps were thinner than expected when a Zyoptix XP 120 microkeratome was used in LASIK. Although the first cuts produced thinner flaps, this difference was not statistically significant. However, the second cuts produced significantly thinner flaps.

Buttonholes During LASIK: Etiology and Outcome

PURPOSE

To report the clinical features and outcome of eyes with flap buttonhole during LASIK.

METHODS

A retrospective review was performed to identify eyes that developed flap buttonhole during Hansatome microkeratome translation. Pre-, intra-, and postoperative data were obtained to identify factors predictive of buttonhole.

RESULTS

Five patients with buttonhole were identified from June 2001 through September 2002 (5 [0.06%] eyes of 7672 primary LASIK procedures). Mean patient age was 49.2 +/- 11.3 years (range: 37 to 66 years). Mean preoperative spherical equivalent refraction was 4.92 +/- 2.90 diopters (D) (range: -2.25 to -9.50 D). Mean keratometry was 45.59 +/- 1.15 D (range: 43.90 to 47.60 D). All 5 flap buttonholes occurred in the second of 2 consecutively treated eyes (P = .03). Buttonhole occurred in 2 (0.26%) of 778 eyes where the 160-microm microkeratome plate was used, and 3 (0.06%) of 4350 eyes where the 180-microm plate was used (P = .16). Two eyes received laser ablation at the time of buttonhole formation. In the untreated cases, the buttonhole flap itself caused a myopic spherical change of -0.50 D and 0.70 D of astigmatism. One of 5 eyes lost 2 lines of best spectacle-corrected visual acuity; this eye received laser ablation immediately after buttonhole formation.

CONCLUSIONS

Buttonholes are significantly more likely to occur in the second of two consecutively treated eyes. A new blade for the second eye when the flap in the first eye appears to be thin should be considered. Caution should be exercised when considering laser ablation immediately following buttonhole formation.

Comparative Study of Stromal Bed Quality by Using Mechanical, IntraLase Femtosecond Laser 15- and 30-kHz Microkeratomes

PURPOSE

To evaluate corneal stromal bed quality of lamellar keratectomy in laser in situ keratomileusis (LASIK) procedures by using mechanical and femtosecond laser microkeratomes.

METHODS

LASIK corneal flaps were created in 9 fresh human globes not suitable for transplantation. We grouped the samples into 3 different groups of 3 globes each. Group 1 was the control group, in which the flaps were created using a Hansatome microkeratome with a 160-microm head. Groups 2 and 3 consisted of flaps created at the 110-microm flap thickness setting using the IntraLase 15- and 30-kHz femtosecond laser, respectively. All the flaps were removed, and the corneal stromal beds were prepared for scanning electron microscopy (SEM). Qualitative surface roughness (QlSR) of the SEM images was graded using a roughness grading scale from 1 to 5 by 3 masked observers. Quantitative surface roughness (QnSR) of the SEM images was also assessed using software designed for roughness analysis. Mann-Whitney nonparametric statistical analysis was performed to compare groups.

RESULTS

There was no statistically significant difference in QlSR and QnSR scores between group 2 and group 1 (brand-new blade only). Group 3 30-kHz IntraLase samples showed a smoother stromal bed compared with group 1 and 2 samples. This was a statistically significant difference for QlSR (QlSR = 1.1 +/- 0.17, P < 0.001) and showed borderline significance for QnSR (QnSR = 24.4 +/- 0.96, P = 0.05).

CONCLUSIONS

The IntraLase 15-kHz femtosecond laser 110-microm flaps and the Hansatome 160-microm head using a new blade both produced smooth, good-quality, compact stromal beds as assessed qualitatively by masked observers and quantitatively by image analysis software. The 30-kHz femotsecond laser permits a tighter spot/line separation and lower energy per pulse, which creates smoother corneal stromal beds.

A 60 kHz IntraLase Femtosecond Laser Creates a Smoother LASIK Stromal Bed Surface Compared to a Zyoptix XP Mechanical Microkeratome in Human Donor Eyes

PURPOSE

To compare the stromal surfaces created by the latest mechanical microkeratome and femtosecond, laser technologies.

METHODS

Laser in situ keratomileusis (LASIK) flaps were created in six fresh human globes unsuitable for transplantation. The eyes were placed in one of two groups of three globes each. One group had LASIK flaps created with a Zyoptix XP microkeratome using a 120-microm head and a fresh blade for each eye. Another group had flaps created at an attempted 100-microm thickness using the 60 kHz IntraLase femtosecond laser. Immediately following flap creation, the stromal beds were prepared for scanning electron microscopy (SEM). Qualitative roughness of the SEM images was graded by masked observers. Quantitative roughness of the SEM images was assessed using computerized software designed for roughness analysis. Mann-Whitney non-parametric statistical analysis was performed to compare groups.

RESULTS

A statistically significant difference was noted in bed smoothness as measured by qualitative roughness and quantitative roughness scores. The IntraLase samples showed smoother stromal beds compared to the Zyoptix group (qualitative roughness = 2.0 +/- 0.7 pm vs 3.6 +/- 1.6 pm, P = .03; quantitative roughness = 20238 +/- 1869 pm vs 26368 +/- 8133 pm, P = .03).

CONCLUSIONS

The 60 kHz IntraLase femtosecond laser and the Zyoptix XP 120-microm head using a new blade produced smooth, good quality, compact stromal beds qualitatively and quantitatively. Because the 60 kHz femtosecond laser permits a tight spot/line separation using low energy, it creates a smoother corneal stromal bed compared to previous femtosecond laser engines.

The effect of flap thickness on the visual and refractive outcome of myopic laser in situ keratomileusis

AIMS

To study the effect of flap thickness on the visual and refractive outcome of myopic laser in situkeratomileusis (LASIK) surgery.

METHODS

A total of 196 myopic eyes with spherical equivalent (SE) from -2.00 to -5.00 dioptres which underwent LASIK were studied retrospectively. Uncorrected visual acuity (UCVA), best-corrected visual acuity (BCVA) and manifest refraction were measured up to 6 months postoperatively. Logistic and linear regression analyses were used to examine the correlation of flap thickness to visual and refractive outcomes, postoperative complications and enhancement rate.

RESULTS

UCVA at 1 week and 1 month, but not at 1 day and at 6 months (P>0.05), were negatively correlated to flap thickness (P<0.05). BCVA was unrelated to flap thickness (P>0.05). At 1-month post-LASIK sphere and cylinder were not related to flap thickness (P>0.05), but spherical equivalent was negatively correlated (P<0.05). Significant negative correlations with the sphere and SE were noticed at 6 months for the eyes not requiring enhancements (P<0.05). Flap thickness had no significant relationship to postoperative complications (P>0.05) and no significant predictive value on the rate of enhancement procedures or the efficacy, safety and predictability indices (P>0.05).

CONCLUSIONS

In myopic LASIK thinner flaps are associated with faster visual recovery and less myopic SE, but the BCVA and the final UCVA are independent of flap thickness. Postoperative complications are unrelated to flap thickness. Flap thickness does not affect the efficacy, safety and predictability, or the rate of enhancement procedures.

Evaluation of Four Microkeratome Models: Quality and Reproducibility of Cut Edge and Cut Surface as Determined by Scanning Electron Microscopy

PURPOSE

To compare the quality and reproducibility of cuts produced by four automatic microkeratomes: Amadeus, Hansatome, Summit-Krumeich-Barraquer (SKBM), and Supratome. For the adjustable models (Amadeus and SKBM), the effects of oscillation frequency and blade feed rate were determined.

METHODS

Eight cuts (flap thickness 160 to 180 microm) were made with each microkeratome at each parameter setting and examined using a scanning electron microscope. Quality of the cut surface was scored for each flap according to four criteria, and results were averaged to give a maximum possible score of 64. Quality of the cut edges was scored from 1 (blurred indistinct edge) to 3 (sharp and clearly visible edge).

RESULTS

The four microkeratomes performed similarly on overall quality of the cut surface (range: 78% to 88% of theoretical maximum). The Hansatome scored highest (88%), followed by SKBM (86%; 1.0 mm/s blade feed and 7000 rpm oscillation), Amadeus (84%; 2.5 mm/s, 8000 rpm), Supratome (84%; 16.6 mm/s, 12,500 rpm), Amadeus (81%; 3.0 mm/s and 13,000 rpm), and SKBM (78%; 1.5 mm/s, 14,000 rpm). Performance differences were clearer for cut edge quality. The Amadeus produced cuts of the highest quality in 62.5% of cases (at both settings), compared with only 12.5% of cases with the Hansatome, 25% of cases with the Supratome and SKMB (1.0 mm/s, 7000 rpm), and in no cases with the SKBM at 1.5 mm/s and 14,000 rpm.

CONCLUSIONS

Overall, high frequency with low blade feed rate is desirable for reproducible sharp edges and cut area quality. However, at very high frequencies (e.g., 14,000 rpm with the SKBM) tissue is displaced, producing an uneven cut area. Oscillation/feed quotients of 2000 to 4000 (rpm/mm x s) are a good compromise. Sharp edges are believed to reduce the risk of comeal erosion, introduction of epithelial cells into the interfacial region, and scarring during wound healing.

Flap dimensions created with the Hansatome microkeratome: correlation with Orbscan-derived anterior segment data

PURPOSE

To investigate the flap dimensions created by Hansatome microkeratome (Bausch & Lomb Surgical) and their correlation with anterior segment biometric data measured by the Orbscan II (Bausch & Lomb).

SETTING

Cerrahpasa Medical Faculty, Istanbul University, Istanbul, Turkey.

METHODS

Forty-four myopic eyes of 22 patients (mean age 29 years +/- 7 [SD]) that had laser in situ keratomileusis surgery using the Hansatome microkeratome were enrolled in the study. Intraoperative images taken from video recordings of procedures were analyzed with image analysis software to determine flap size and hinge size. White-to-white corneal diameter, corneal curvatures (K(max), K(min)), corneal thickness, and anterior chamber depth were deducted from Orbscan measurement. Correlation analyses between flap dimensions and Orbscan-derived anterior segment biometric data were done.

RESULTS

The mean corneal flap diameter was 9.56 +/- 0.28 mm in the right eye and 9.62 +/- 0.28 mm in the left eye. There was no difference in flap size between the right and left eyes (P=.43). The mean hinge size was 4.98 +/- 0.37 mm in the right eye and 5.07 +/- 0.41 mm in the left eye. There was no difference in hinge size between the right and left eyes (P=.46). There was a significant correlation between flap size and preoperative corneal thickness (P<.001, r=0.487), but there was no correlation between flap size and corneal curvature (P=.40, r=-0.12), white-to-white corneal diameter (P=.11, r=0.47), or anterior chamber depth (P=.52, r=0.09). There was also no correlation between hinge size and preoperative anterior segment biometric data.

CONCLUSION

The Hansatome microkeratome produced a flap whose diameter is close to the intended flap diameter, and preoperative corneal thickness seems to be the important factor in determining flap size.

Amadeus microkeratome: experience with the first 2000 cases and lessons learned

BACKGROUND

To assess the safety and efficacy of the Amadeus microkeratome and to report on lessons learnt in optimizing results from its use.

METHODS

A retrospective review of the flap-related complications of 2000 laser in situ keratomileusis (LASIK) procedures performed by one surgeon using the Amadeus microkeratome (AMO, Irvine, CA, USA) was conducted. One hundred consecutive cases had preoperative and intraoperative pachymetry to evaluate the relationship between flap thickness, corneal thickness and reuse of the blade.

RESULTS

There were 35 cases of minor epithelial defects (1.8%) and four eyes with major epithelial defects (0.2%). There were no cases of suction loss, buttonholes, or incomplete or damaged flaps. There were four free caps (0.2%). Twenty-five cases had minor wrinkles and two cases had significant folds requiring relifts. Thinner corneas resulted in thinner flaps (P < 0.0001). Reuse of the blade resulted in thinner flaps (P = 0.0001).

CONCLUSION

The Amadeus is a safe and reliable microkeratome. Although short, there is a learning curve with use of the instrument. Corneal thickness and reuse of the blade affect flap thickness.

Factors Predictive of LASIK Flap Thickness With the Hansatome Zero Compression Microkeratome

PURPOSE

To determine the explanatory power of preoperative variables and comeal flap thickness in laser in situ keratomileusis (LASIK) using the Hansatome zero compression microkeratome (Bausch & Lomb, Rochester, NY).

METHODS

A prospective, nonrandomized, comparative interventional case study was performed on 250 eyes of 129 consecutive patients who underwent LASIK surgery using the Hansatome zero compression microkeratome. A 160-microm or 180-microm microkeratome head and an 8.5- or 9.5-mm suction ring were used in the procedures. Preoperative measurements included refraction, spherical equivalent, keratometry, intraocular pressure, corneal white-to-white, anterior chamber depth, and corneal eccentricity. Corneal thickness was measured intraoperatively using ultrasonic pachymetry before and after flap creation, and the difference was taken as flap thickness. Flap diameter was measured with a corneal gauge. Data were analyzed using simple, multiple, stepwise linear and non-linear regression analyses and two-tailed t tests.

RESULTS

The mean flap thickness was 124 +/- 17 microm with the nominal 160-microm head and 142 +/- 20 microm with the nominal 180-microm head. One third (33%) of the total variation in flap thickness could be accounted for by three preoperative variables: average corneal thickness, spherical equivalent refraction, and choice of 160- or 180-microm microkeratome head. A simple correlation of 0.114 was noted between corneal eccentricity and flap thickness, but this variable did not add significant explanatory power on multiple regression analysis. Linear regression analysis allowed determination of a flap thickness nomogram with a standard error of the estimate of 16.9 microm and a 95% confidence interval of +/- 33.1.

CONCLUSIONS

Comeal thickness is the most systematic predictor of corneal flap thickness using the Hansatome microkeratome. Because three preoperative variables account for only 33% of the range in flap thickness, future studies should focus on variations in blade extension and corneal biomechanical factors, which may also play an important role in determining flap thickness.

Pathologic findings in postmortem corneas after successful laser in situ keratomileusis

PURPOSE

To examine the histologic and ultrastructural features of human corneas after successful laser in situ keratomileusis (LASIK).

METHODS

Corneas from 48 eyes of 25 postmortem patients were processed for histology and transmission electron microscopy (TEM). The 25 patients had LASIK between 3 months and 7 years prior to death. Evaluation of all 5 layers of the cornea and the LASIK flap interface region was done using routine histology, periodic acid-Schiff (PAS)-stained specimens, toluidine blue-stained thick sections, and TEM.

RESULTS

In patients for whom visual acuity was known, the first postoperative day uncorrected visual acuity was 20/15 to 20/30. In patients for whom clinical records were available, the postoperative corneal topography was normal and clinical examination showed a semicircular ring of haze at the wound margin of the LASIK flap. Histologically, the LASIK flap measured, on average, 142.7 microm (range, 100-200). A spectrum of abnormal histopathologic and ultrastructural findings was present in all corneas. Findings at the flap surface included elongated basal epithelial cells, epithelial hyperplasia, thickening and undulations of the epithelial basement membrane (EBM), and undulations of Bowman's layer. Findings in or adjacent to the wound included collagen lamellar disarray; activated keratocytes; quiescent keratocytes with small vacuoles; epithelial ingrowth; eosinophilic deposits; PAS-positive, electron-dense granular material interspersed with randomly ordered collagen fibrils; increased spacing between collagen fibrils; and widely spaced banded collagen. There was no observable correlation between postoperative intervals and the severity or type of pathologic change except for the accumulation the electron-dense granular material.

CONCLUSIONS

Permanent pathologic changes were present in all post-LASIK corneas. These changes were most prevalent in the lamellar interface wound. These changes along with other pathologic alterations in post-LASIK corneas may change the functionality of the cornea after LASIK.

Structural analysis of the cornea using scanning-slit corneal topography in eyes undergoing excimer laser refractive surgery

PURPOSE

To review the time course of corneal anteroposterior shift and refractive stability after myopic excimer laser keratorefractive surgery.

METHODS

We examined 65 eyes undergoing photorefractive keratectomy (PRK) and 45 eyes undergoing laser in situ keratomileusis (LASIK). Corneal elevation maps and pachymetry were obtained by scanning-slit corneal topography before; 1 week; and 1, 3, 6, and 12 months after surgery.

RESULTS

Both PRK and LASIK induced significant forward shifts of the cornea. Corneal forward shift was progressive up to 6 months after PRK, but no progression was seen after LASIK. Progressive thinning and expansion of the cornea were not observed after either procedure. The amount of corneal forward shift showed a significant negative correlation with preoperative corneal thickness (r = -0.586; P < 0.01) and a significant positive correlation with the amount of myopic correction (r = 0.504; P < 0.01). A significant correlation was found between the amount of forward shift and the degree of myopic regression after surgery (r = -0.347; P < 0.05).

CONCLUSION

Myopic PRK and LASIK induce significant forward shifts of the cornea, which are not true corneal ectasia. Eyes with thinner corneas and higher myopia requiring greater ablation are more predisposed to anterior protrusion of the cornea. Corneal forward shift was progressive up to 6 months after PRK but not progressive after LASIK. Forward shift of the cornea can be one of the factors responsible for myopic regression after surgery.

The effect of hinge position and depth plate on the rate of recovery of corneal sensation following LASIK

PURPOSE

To evaluate and compare the effect of hinge position and flap thickness on recovery rate of corneal sensation after (LASIK).

DESIGN

Prospective, randomized clinical study.

METHODS

Forty eyes of 40 patients underwent LASIK to correct myopia ranging from -1.00 to -2.50 diopters. Corneal sensitivity was measured preoperatively and each month after surgery until recovery to preoperative level. The nasal-hinged ACS microkeratome (NH) with depth plates of 130 and 160 microm and the superior-hinged Hansatome microkeratome (SH) with depth plates of 160 and 180 microm were used for corneal flap creation. The eyes were divided into four groups according to the hinge position and depth plate (DP): group 1, NH and 130 microm DP; group 2, NH and 160 microm DP; group 3, SH and 160 microm DP; group 4, SH and 180 microm DP.

RESULTS

Corneal sensitivity returned to preoperative level after 3.7 (+/- 0.4), 4.4 (+/- 0.6), 5.4 (+/- 0.8), and 5.8 (+/- 0.9) months, respectively, in groups 1, 2, 3, and 4. Statistically significant differences were found between groups 1 and 2, but not between groups 3 and 4. Corneal sensitivity gradually returned to preoperative levels in all groups. Sensitivity of the hinge area was higher than other areas at every time point.

CONCLUSIONS

The results suggest that after LASIK, hinge position and flap thickness seem to be important factors in the rate of return of corneal sensitivity. A thin flap with a nasally placed hinge is associated with the most rapid recovery of corneal sensitivity.

Evaluation of cut quality using the Amadeus microkeratome with different settings

PURPOSE

To evaluate the quality of keratectomy specimens created with the Amadeus microkeratome (AMO) using scanning electron microscopy (SEM).

SETTING

Johannes Gutenberg-University Hospital, Department of Ophthalmology, Mainz, and the Department of Anatomy, Justus Liebig-University, Giessen, Germany.

METHODS

Corneal cuts were performed in freshly enucleated pig eyes using the Amadeus microkeratome with 9 combinations of oscillation rate and head-advance speed. For the cutting trials, oscillation rates of 8000, 13,000, and 18,000 rpm and head-advance speeds of 1.0, 2.5, and 4.0 mm/s were chosen. Fifty-four eyes were included, resulting in 9 groups of 6 eyes for each configuration. The surfaces and edges of the flaps were examined using SEM.

RESULTS

At fixed oscillation rates, an increase in head-advance speed led to lower quality cuts, higher surface roughness, and irregular cut edges. At fixed head-advance speeds, an increase in oscillation rates improved the cut quality, resulting in smoother surface characteristics.

CONCLUSIONS

Smooth and regular surfaces and cut edges can be achieved by choosing high oscillation rates and low head-advance speeds. Microkeratomes that enable the user to adjust the oscillation rate and head-advance speed can be used to maximize surface smoothness and improve customized refractive surgery.

Retrospective analysis of actual LASIK flap diameter compared with microkeratome ring size performed by different surgeons

PURPOSE

To evaluate the difference in the diameter between microkeratome ring and actual laser in situ keratomileusis (LASIK) flap size by 4 different surgeons using 3 different microkeratomes in comparison to preoperative keratometry.

SETTING

Gimbel Eye Centre, Calgary, Alberta, Canada.

METHODS

A retrospective analysis of 6667 consecutive LASIK surgeries performed at the Gimbel Eye Centre between 1998 and 2002 was conducted. The study compared the difference in the actual LASIK flap diameter and microkeratome ring size for 3 Hansatome microkeratomes indicated by serial numbers 2230, 3048, and 3084 in comparison to the preoperative keratometry. The surgeries were performed by 4 surgeons from the Centre.

RESULTS

A statistically significant correlation was found between the actual flap size and the microkeratome ring size. The deviation increased with corneal steepness (#2230: r = 0.45, P<.001; #3048: r = 0.28, P<.001; #3084: r = 0.23, P<.001). The mean difference between actual flap size and the microkeratome ring size was 0.647 mm, 0.808 mm, and 0.916 mm for Hansatome microkeratome #2230, #3048, and #3084, respectively. The actual flap was larger than the microkeratome ring size in 92.8%, 93.8%, and 97.4% of eyes, respectively. The mean difference between microkeratome ring size and measured LASIK flap size was consistently significantly different (P<.0001) per surgeon for all microkeratomes.

CONCLUSIONS

Estimation of the flap size is an important issue while selecting ring size and planning the treatment zone. In this study, the actual flap size was larger than the ring size for all surgeons and all 3 Hansatome microkeratomes. Higher preoperative keratometry values achieved larger flaps than those with lower keratometry values.

Reproducibility of LASIK flap thickness using the Hansatome microkeratome

PURPOSE

To evaluate the actual versus the expected thickness of laser in situ keratomileusis (LASIK) flaps and to determine the factors that affect flap thickness.

SETTING

Centre For Sight, Queen Victoria Hospital, East Grinstead, United Kingdom.

METHODS

A retrospective analysis of LASIK procedures in 757 consecutive eyes was done. The surgery was performed by a single surgeon using 2 Hansatome microkeratomes (Bausch & Lomb) with 160 microm and 180 microm heads. Patient age, preoperative manifest refraction, automated keratometry, preoperative central pachymetry, and intraoperative stromal pachymetry were evaluated to determine whether they influenced the actual flap thickness.

RESULTS

Bilateral LASIK was performed in 343 patients (686 eyes). The 160 microm head was used in 641 eyes (84.6%) (Group 1) and the 180 microm head, in 116 eyes (15.4%) (Group 2). The mean preoperative manifest refraction spherical equivalent (SE) was -3.9 diopters (D) +/- 4.5 (SD) (range +7.4 to -25.0 D) in Group 1 and -4.4 +/- 3.7 D (range +7.1 to -12.9 D) in Group 2. The mean preoperative keratometry reading was 43.6 +/- 1.8 D (range 36.0 to 48.6 D) and 43.6 +/- 1.8 D (range 35.9 to 47.0 D), respectively; the mean preoperative central pachymetry was 543 +/- 35 microm (range 447 to 643 microm) and 548 +/- 31 microm (range 453 to 613 microm), respectively; and the mean flap thickness was 116.4 +/- 19.8 microm and 117.3 +/- 18.0 microm, respectively. The difference between the actual and the expected flap thickness in each group was statistically significant (P<.001). There was no significant difference in the actual flap thickness between the 2 Hansatomes. The preoperative SE and central pachymetry were the only factors that influenced the actual flap thickness (P<.05); thin flaps were more common with increasing myopia and increasing corneal thickness.

CONCLUSIONS

Spherical equivalent and preoperative pachymetry were the principal factors that influenced flap thickness. Preoperative keratometry values and patient age did not influence the actual flap thickness.

Risk factors and retreatment results of intraoperative flap complications in LASIK

PURPOSE

To evaluate the incidence, type, and risk factors of intraoperative complications leading to abandonment of laser in situ keratomileusis (LASIK), and to compare the safety and efficacy of retreated LASIK with uncomplicated primary LASIK.

SETTING

Refractive surgery centers in Tokyo, Yokohama, Nagoya, Osaka, and Fukuoka, Japan.

METHODS

A total of 3751 eyes of 2033 patients who were followed for 6 months after primary LASIK, of which 15 eyes were retreated after intraoperative flap complications, were reviewed. In most of the cases, retreatments were performed by recutting a new flap.

RESULTS

Intraoperative flap complications occurred in 25 eyes, of which 15 eyes had retreatment at a later date. The overall incidence of complications was independent of the surgeons' experience, although incomplete flaps, in particular, occurred at a higher rate in the hands of inexperienced surgeons. No patient profile was detected as a risk factor for intraoperative flap complications. No flap-related complications occurred at retreatment. Refractive and visual outcomes were comparable to those in the uncomplicated cases within 6 months postoperatively.

CONCLUSIONS

Retreatment after microkeratome flap complications by recutting the cornea is safe and effective.

Flap Quality in Single Versus Multiple Use of the Same Blade in the Flapmaker Microkeratome

PURPOSE

We evaluated experimentally the variability of cut thickness, flap diameter, and cut quality produced by the Flapmaker corneal microkeratome (IOLTech), with single and repeated use of the same cutting blade.

METHODS

Keratectomy was performed with twelve cutting heads (8.5-mm diameter, 160-microm cutting depth) on 47 corneas and with six cutting heads (8.0-mm diameter, 180-microm cutting depth) on 18 freshly enucleated swine eyes in a repeated manner. Ultrasonic pachymetry was determined at the initial, central, and final microkeratome pass zones, first before the flap was created and subsequently after the flap was reflected. Flap diameter was measured by planimetry. After the procedure stromal portions were submitted for scanning electron microscopy.

RESULTS

On the first blade use, mean central flap thickness was 145 +/- 32 microm and mean vertical flap diameter was 8.4 +/- 0.26 mm with the 8.5-mm blades. With the 8.0-mm blades, mean central flap thickness was 155 +/- 23 microm and mean vertical flap diameter was 8.0 +/- 0.27 mm. Scanning electron microscopy disclosed smooth cut surfaces when new blades were used, but with repeated blade use, increasingly prominent stromal bed folds were observed.

CONCLUSIONS

The evaluated blades produced reproducible flap size and thickness and good cut quality with single use, but after the first use, cut quality markedly deteriorated. Repeated use of Flapmaker cutting blades is not recommended.

Comparison of Corneal Flap Thickness Between Primary and Fellow Eyes Using Three Microkeratomes

PURPOSE

To compare corneal flap thickness created in laser in situ keratomileusis (LASIK) in primary (right) and fellow (left) eyes (same blade for both eyes) using three microkeratomes.

METHODS

The corneal thickness of 132 eyes (66 patients) was measured preoperatively and intraoperatively after flap creation. Corneal flap thickness was calculated by subtracting stromal bed thickness from total corneal thickness. Three microkeratomes were used: Nidek MK-2000, Bausch and Lomb Surgical Hansatome, and the Chiron Automated Corneal Shaper (ACS). Each patient had both corneas cut by one microkeratome and one blade at the same session.

RESULTS

Mean corneal flap thickness created in primary eyes was 128.30 +/- 12.57 microm (range 105 to 147 microm) for the ACS (160-microm plate and 8.5-mm ring) and 122.96 +/- 13.30 microm (range 86 to 140 microm) for fellow eyes; Hansatome (160-microm plate and 8.5-mm ring): 141.16 +/- 20.11 microm (range 101 to 169 microm) in primary eyes and 120.95 +/- 26.95 microm (range 107 to 151 microm) in fellow eyes; Nidek (130-microm plate and 8.5-mm ring): 127.25 +/- 4.12 microm (range 116 to 134 microm) in primary eyes and 127.54 +/- 3.7 microm (range 119 to 134 microm) in fellow eyes. The corneal flap in the ACS and Hansatome microkeratomes was always thicker in the primary than the fellow eye, using the same blade for both eyes. No significant difference was found using the Nidek microkeratome.

CONCLUSION

Corneal flap thickness tended to be thinner in fellow eyes than in primary eyes for the ACS and Hanstome microkeratomes. The Nidek microkeratome results were closer to specified corneal flap thickness than the ACS and Hanstome microkeratomes.

Penetrating keratoplasty for iatrogenic keratoconus after repeat myopic laser in situ keratomileusis: Histologic findings and literature review

We report a patient with a sufficiently thick cornea (593 microm) and no topographic signs of keratoconus preoperatively who developed iatrogenic keratoconus 2 months after repeat laser in situ keratomileusis (-4.00 -1.00 x 20) performed 5 months after the primary procedure (-10.50 -1.00 x 55). After penetrating keratoplasty, macrophotography showed severe multidirectional "macrostriae" of the stromal bed. On histologic evaluation, excessive thinning of the residual stromal bed to a minimum of 75 microm in the valleys and a maximum of 200 microm at the peaks of the macrostriae were documented. The flap thickness was 225 microm in the center. The thicker-than-intended flap (160 microm) is thought to be the cause of the severe complication of the LASIK procedure.

Accuracy and precision of the amadeus microkeratome in producing LASIK flaps

PURPOSE

To evaluate the accuracy and precision of corneal flap thickness following laser in situ keratomileusis (LASIK) performed using the 140-, 160-, and 180-microm heads for the Amadeus microkeratome (AMO, Irvine, CA).

SETTING

The study took place at the Cullen Eye Institute, Baylor College of Medicine, Houston.

METHODS

In this prospective study, using the Amadeus microkeratome, LASIK flaps were cut in 51 right eyes and 50 left eyes with the 140-microm head, 25 right eyes and 25 left eyes with the 160-microm head, and five right eyes and one left eye with the 180-microm head. The same microkeratome blade was used for bilateral cases with the right eyes always undergoing surgery first. Eyes were grouped by order of blade use for statistical analysis. The effect of preoperative corneal thickness, keratometry values, blade oscillation and translation speeds, and blade reuse on flap thickness was evaluated.

RESULTS

Mean flap thicknesses were 153 +/- 18 (range 97-187 microm) OD and 134 +/- 25 microm (range 79-174 microm) OS for the 140-microm head; 182 +/- 26 microm (range 105-220 microm) OD and 163 +/- 29 microm (range 105-216 microm) OS for the 160-microm head; and 235 +/- 24 microm (range 198-258 microm) for the 180-microm head. Flap thickness was significantly thicker for the first eyes cut (right eyes) and was positively correlated with increasing corneal thickness in both eyes. For the first eyes cut, flap thickness was also significantly thicker than the labeled thickness specified by the manufacturer.

CONCLUSIONS

With the Amadeus microkeratome, LASIK flap thickness correlated with central corneal thickness for the 140-microm head. Reuse of the microkeratome blades produced significantly thinner LASIK flaps on second eyes cut.

Evaluation of corneal flap dimensions and cut quality using the SKBM automated microkeratome

PURPOSE

To evaluate flap dimensions and cut quality with repeated blade use of the automated Summit Krumeich-Barraquer microkeratome (SKBM [LadarVision]).

SETTING

Department of Ophthalmology, University Erlangen-Nuremberg, Erlangen, Germany.

METHODS

The SKBM (160 microm plate, intended flap diameter 9.0 mm) was used to perform a corneal hinged flap in 35 pig cadaver eyes. Seven blades were reused 5 times each. The flap diameter was measured by planimetry, and the thickness was assessed by ultrasonic pachymetry. Scanning electron microscopy (SEM) of blades and stromal beds was performed.

RESULTS

With single use of the blade, the mean central flap thickness was 145 microm +/- 25 (SD). The vertical/horizontal flap diameter was 9.0 +/- 0.03 mm/8.6 +/- 0.03 mm. No thickness gradient was observed from the incision (138 +/- 31 microm) to the flap hinge (130 +/- 30 microm). If the blade was used more than 2 times, the flap was thinner at the incision (157 +/- 34 microm versus 124 +/- 20 microm; P =.003) and the hinge (143 +/- 24 microm versus 122 +/- 31 microm; P =.04), but the central thickness remained unchanged. With multiple use of the blade, SEM analysis showed increasing cut irregularity, more tissue remnants on the blade surface, and a progression in blade irregularities (up to 9.3 microm).

CONCLUSIONS

Reproducible flap size and thickness can be obtained with single use of stainless steel blades in the SKBM. With multiple use, the quality of the blades and the stromal bed deteriorates and the peripheral thickness of the flaps decreases. Thus, single use of blades is recommended.

Precision of Flap Measurements for Laser in situ Keratomileusis in 4428 Eyes

PURPOSE

To determine the factor(s) that influence the dimensions and predictability of the LASIK corneal flap with the Automated Corneal Shaper (ACS) or the Summit Krumeich Barraquer microkeratome (SKBM).

METHODS

We performed a retrospective, comparative interventional case study of 4,428 eyes. Flap dimensions were measured using subtraction ultrasonic pachymetry during LASIK with one of two microkeratomes.

RESULTS

Mean preoperative corneal thickness for all eyes was 555 +/- 35 microm. Corneal curvature and refractive astigmatism were inversely related to preoperative corneal thickness (P<.001). With an attempted flap thickness of 160 microm, the ACS flap thickness averaged 119.8 +/- 22.9 microm; SKBM flaps averaged 160.9 +/- 24.1 microm (P<.001). The coefficient of variation for central pachymetry compared to flap thickness was 6.4% vs. 22.1%. Flap thickness at enhancement was 10 to 17 microm thicker than at primary surgery. An increase in flap thickness was associated with thicker preoperative pachymetry (P<.001) and younger age for both instruments (P<.001) whereas increasing flap thickness was related to flatter preoperative mean keratometry for the ACS (P<.001) and steeper mean keratometry for the SKBM (P=.005). Less preoperative hyperopia or more myopia was related to an increase in flap thickness only for the SKBM (P<.001).

CONCLUSIONS

Flap thickness varies significantly depending on the microkeratome used. Factors that influence flap thickness are primarily corneal thickness, patient age, preoperative keratometry, preoperative refraction including astigmatism, and corneal diameter. By understanding the factors that affect flap thickness, one can select a microkeratome system to allow maximum refractive correction while minimizing the risk of ectasia.

Factors That Affect Corneal Flap Thickness With the Hansatome Microkeratome

PURPOSE

To evaluate factors that influence corneal flap thickness with the Hansatome microkeratome.

METHODS

One hundred thirty-two eyes of 70 patients underwent laser in situ keratomileusis (LASIK). Corneal flap thickness was measured by subtracting the intraoperative corneal bed pachymetry measurement from intraoperative total corneal pachymetry. Variables examined included plate thickness, ring size, blade use, temperature, humidity, barometric pressure, age, average keratometric power, and preoperative corneal thickness.

RESULTS

Mean flap thickness using a 180-microm plate was 143 +/- 19 microm (range 61 to 207 microm). Mean flap thickness using a 160-microm plate was 119 +/- 20 microm (range 83 to 159 microm). The difference was statistically significant (P < .05). Mean flap thickness using a 180-microm plate and the same blade on the right and left eye was 151 +/- 21 microm (range 113 to 200 microm) and 137 +/- 21 microm (range 91 to 191 microm), respectively. The 14-microm difference was statistically significant (P < .001). There was a slight negative correlation of flap thickness with humidity. There was a positive correlation with preoperative corneal thickness (pachymetry).

CONCLUSION

The Hansatome tended to cut thinner flaps than anticipated based on the plate used. Flaps cut on the first eye were thicker than the second eye using the same blade. Thicker corneas tended to lead to thicker flaps. There was no correlation between flap thickness and microkeratome ring size, temperature, barometric pressure, patient age, or average keratometric power.

Changes of posterior corneal astigmatism and tilt after myopic laser in situ keratomileusis

PURPOSE

The purpose of this study was to assess the changes of posterior corneal astigmatism and tilt after laser in situ keratomileusis (LASIK) and to correlate these changes with the amount of correction and the residual stromal bed thickness.

METHODS

This prospective nonrandomized (self-controlled) comparative trial included 57 eyes from 14 females and 15 males, whose mean age (+/- standard deviation [SD]) at the time of surgery was 33 +/- 9 years (range, 19-53), with a spherical equivalent (SEQ) of -1.00 to -15.50 (mean, -5.07 +/- 2.81) diopters (D). All LASIK procedures were accomplished with the Keratom II Coherent-Schwind excimer laser and the Moria Model One microkeratome (150-microm head). Subjective refractometry, Orbscan slit-scanning corneal topography analysis, and pachymetry were performed before and 3 months after LASIK for myopia (n= 35; -1.00 to -15.50 D [mean, -4.75 +/- 3.07]) or myopic astigmatism (n= 22; sphere, 0.00 to -9.75 D [mean, -4.75 +/- 2.36]; cylinder, -0.75 to -3.50 D [-1.68 +/- 0.86]). Intended ablation depth ranged from 12 to 108 (mean, 48 +/- 22) microm. Topographic raw data were decomposed into a set of Zernike polynomials as published in detail previously, and parameters for detection of asymmetric mechanical deformation of the cornea were derived. Posterior corneal astigmatism and tilt before and after LASIK were compared, and changes in these variables were correlated with the SEQ change (DeltaSEQ) and the residual corneal bed thickness (RBT).

RESULTS

The RBT after LASIK ranged from 186 to 373 (mean, 280 +/- 42) microm. Overall, astigmatism (0.19 +/- 0.07 D/0.22 +/- 0.13 D; p= 0.80) and tilt (3.58 +/- 0.35 degrees /3.65 +/- 0.48 degrees; p= 0.61) did not change significantly by 3 months after LASIK. In eyes with RBT < or =250 microm, the average change in astigmatism (0.05 +/- 0.11 versus 0.01 +/- 0.13 D; p= 0.46) and tilt (0.21 +/- 0.45 degrees versus 0.04 +/- 0.55 degrees; p= 0.30) was not greater than in eyes with RBT > 250 microm. Change in astigmatism (p= 0.19) and tilt (p= 0.56) did not correlate with the RBT during LASIK.

CONCLUSIONS

Zernike decomposition of topographic height data discloses that no significant asymmetric mechanical deformation of the posterior corneal curvature occurs after myopic LASIK. Further studies with long-term follow-up are needed to clarify whether this symmetry of the posterior corneal surface can indeed be preserved over time after LASIK if the RBT is < 250 microm.

In vivo confocal microscopy through-focusing to measure corneal flap thickness after laser in situ keratomileusis

PURPOSE

To measure flap thickness in laser in situ keratomileusis (LASIK) patients using in vivo confocal microscopy through-focusing (CMTF) and compare measured versus intended flap thickness achieved by 2 microkeratomes, the Automated Corneal Shaper(R) (ACS) (Chiron Bausch & Lomb) and the Hansatome (Bausch & Lomb).

SETTING

Department of Ophthalmology, University of Texas Southwestern Medical Center at Dallas, Dallas, Texas, USA.

METHODS

Twenty-seven eyes of 27 patients were examined by in vivo CMTF 3 to 12 months after LASIK was performed with the ACS (12 patients) or Hansatome (15 patients) microkeratome. The central cornea was scanned, and the epithelium, flap, stroma, and total corneal thickness were measured. Normalized flap thickness (NFT) was also calculated to account for changes in epithelial thickness that may have occurred postoperatively.

RESULTS

The mean posterior stromal thickness was 341.1 microm +/- 53.9 (SD) (range 233 to 431 microm) in the ACS group and 320.3 +/- 42.3 microm (range 258 to 382 microm) in the Hansatome group. The mean nonnormalized flap thickness was 132.7 +/- 12.5 microm (range 11 to 151 microm) in the ACS group and 167.4 +/- 21.4 microm (range 141 to 209 microm) in the Hansatome group. The NFT was 129.6 +/- 9.5 microm and 158.4 +/- 22.1 microm, respectively. Both microkeratomes cut significantly less than intended (P <.05); however, the ACS cut a thinner-than-intended thickness in all cases, and the Hansatome cut thicker than intended in 13% of cases. The Hansatome also showed significantly greater variability in flap thickness than the ACS (P <.05).

CONCLUSIONS

A significant difference in precision was noted between the 2 microkeratomes. The findings emphasize the importance of performing thickness measurements and the usefulness of in vivo CMTF in making these determinations to ensure the safety and effectiveness of LASIK.

Predictability of Corneal Flap Thickness in Laser in situ Keratomileusis Using Three Different Microkeratomes

PURPOSE

To compare the accuracy and consistency of corneal flap thickness in the right and left eye created by three different widely used microkeratomes during consecutive laser in situ keratomileusis (LASIK).

METHODS

Corneal thickness of 132 eyes of 66 patients was measured preoperatively and intraoperatively. Corneal flap thickness was calculated by subtracting the corneal stromal thickness from the total corneal thickness. Three different microkeratomes were used for creating the corneal flap: Chiron Automated Corneal Shaper (ACS), Baush and Lomb Surgical Hansatome, and Nidek MK 2000 microkeratomes. The same surgeon performed all procedures on the right eye first and then on the left eye using the same blade and the same surgical technique.

RESULTS

Mean corneal flap thickness created by the ACS (160-microm depth setting) microkeratome was 128.30 +/- 12.57 microm in the right eye and 122.96 +/- 13.30 microm in the left eye. The Hansatome (160-microm depth plate) microkeratome created a flap of mean 141.16 +/- 20.11 microm in the right eye and 120.95 +/- 26.95 microm in the left eye, and the Nidek MK 2000 (130-microm depth plate) microkeratome created a flap of 127.25 +/- 4.12 microm in the right eye and 127.54 +/- 3.7 microm in the left eye.

CONCLUSION

Corneal flap thickness tended to be considerably thinner than expected on both eyes using the ACS and Hansatome. With the ACS and Hansatome, the difference in corneal flap thickness between the first and second operated eye was statistically significant. With the Nidek MK 2000 microkeratome, there was no statistically significant difference between the first and second operated eye and measurements were close to desired corneal flap thickness. Intraoperative pachymetry is recommended for every LASIK procedure.

Corneal flap thickness in laser in situ keratomileusis using the summit Krumeich-Barraquer microkeratome

PURPOSE

To evaluate the thickness of corneal flaps created by the Summit Krumeich-Barraquer microkeratome (SKBM) (Alcon Surgical) and identify factors that may influence flap thickness.

SETTING

SSK Ankara Eye Hospital, Ankara, Turkey.

METHODS

Seventy-eight eyes of 50 patients who had laser in situ keratomileusis with the Asclepion-Meditec MEL 70 G-Scan excimer laser and the SKBM were prospectively evaluated. Preoperatively, the central corneal thickness, keratometry, visual acuity, and manifest refraction were measured. The microkeratome with the suction ring designed to create 160 microm thick and 9.0 to 9.5 mm diameter flaps was used in all eyes. Stromal bed thickness was measured with the Pachette ultrasonic pachymeter (DGH Technology, Inc.) after the flap was lifted. Flap thickness was calculated by subtracting the central stromal bed thickness from the preoperative central corneal thickness.

RESULTS

The mean preoperative central corneal thickness was 546.7 microm +/- 31.9 (SD), the mean manifest refraction spherical equivalent was -6.8 +/- 3.4 diopters (D), and the mean corneal refractive power was 42.9 +/- 1.5 D. The mean corneal flap thickness created by the microkeratome was 154.9 +/- 19.3 microm (range 101 to 202 microm). There was no correlation between corneal flap thickness and the degree of myopia (P =.151) or the corneal refractive power (P =.257). There was a linear relationship between flap thickness and the preoperative central corneal thickness (P =.000). A posterior corneal stroma thicker than 250 microm was preserved in 87 eyes (98.9%).

CONCLUSIONS

The SKBM produced corneal flaps that were consistently close to the intended thickness. Corneal flap thickness did not appear to be influenced by the degree of myopia or the corneal refractive power; however, there was a linear relationship between flap thickness and the preoperative central corneal thickness.

Flap Measurements With the Hansatome Microkeratome

PURPOSE

To evaluate flap thickness, flap diameter, and hinge length during laser in situ keratomileusis (LASIK) and to correlate these measurements with preoperative keratometric power, central corneal thickness, and patient refraction, gender, and age.

METHODS

In this prospective study of 50 eyes of 28 patients (mean age 31 +/- 6.6 yr; range, 24 to 43 yr) results of LASIK for myopia were analyzed (mean spherical equivalent refraction of -7.16 +/- 1.69 D; range, -2.75 to -13.50 D). Corneal flaps were created using the Hansatome microkeratome (Baush & Lomb Surgical) with a 160-microm plate and a 9.5-mm suction ring. Corneal thickness was evaluated using an ultrasonic 50-MHz pachymeter (Sonogage Corneo Gage Plus) and the mean keratometric power was measured with a Corneal Analysis System videokeratographic unit (EyeSys). Data were analyzed using t-test, Pearson product moment correlation coefficient, and Spearman's rho non-parametric correlation coefficients.

RESULTS

Mean corneal flap thickness was 142.6 +/- 20.8 microm (range, 107 to 177 microm), mean flap diameter was 9.9 +/- 0.3 mm (range, 9.2 to 10.5 mm), and mean hinge length was 6.2 +/- 0.4 mm (range, 5.2 to 7 mm). Statistically significant correlations (P<.05) were found between mean keratometric power and flap hinge length, mean keratometric power and flap diameter, preoperative spherical equivalent refraction and flap diameter, corneal thickness and flap hinge length, as well as patient age and corneal thickness.

CONCLUSIONS

The Hansatome microkeratome was an effective and safe instrument in the creation of corneal flaps for LASIK. Consideration of preoperative keratometric power and corneal thickness may help to reduce or avoid complications.

Scanning electron microscopic evaluation of the surface characteristics of 4 microkeratome systems in human corneas

PURPOSE

To evaluate the surface characteristics of keratectomy specimens created with 4 microkeratomes by scanning electron microscopy (SEM).

SETTING

Two university institutions.

METHODS

Keratectomies were performed in 10 fresh, unfrozen human eyes with 1 of 4 microkeratomes: the Draeger rotary microkeratome (Storz Instruments), the Universalkeratome (Phoenix), the Automated Corneal Shaper (Bausch & Lomb), or the Hansatome (Bausch & Lomb). The beds and edges of the keratectomy specimens were then examined by SEM. Standardized photographs were taken, and the surface and cut-edge characteristics of the keratectomies were compared.

RESULTS

Irregularities were noted in the cut edges of Bowman's membrane and the surface of the keratectomy beds with all instruments. The irregularities were most prominent in corneas cut with the Draeger instrument and least prominent in those cut with the Universalkeratome. The serrations in Bowman's membrane and the irregularities in the keratectomy bed appeared to be related to the blade movement in oscillating blade instruments.

CONCLUSIONS

All 4 microkeratomes caused some degree of surface irregularity. The Draeger microkeratome, which uses a continuously rotating blade, resulted in the greatest number of Bowman's membrane serrations and irregularities in the keratectomy bed. The tissue irregularities may be related to the development of pressure ridges ahead of the blade. In instruments that use an oscillating blade, chatter marks appear to be related to the reciprocating movement of the blade as it travels across the corneal stroma.

Incidence of intraoperative flap complications in laser in situ keratomileusis

PURPOSE

To evaluate the incidence of intraoperative flap complications in laser in situ keratomileusis (LASIK) and compare the incidence between eyes and between the Hansatome and Automated Corneal Shaper (Bausch & Lomb) microkeratomes.

SETTING

Open-access outpatient excimer laser surgical facility.

METHODS

A retrospective analysis was done of 84711 primary LASIK cases performed between November 1998 and May 2000 in 28 national open-access laser facilities. The intraoperative flap complications were identified and categorized into type of complication, eye involved, and microkeratome type. All cases used the Automated Corneal Shaper or the Hansatome microkeratome.

RESULTS

Two hundred fifty-six complications (0.302%) were identified: 29 failures to achieve intraocular pressure (0.034%), 84 partial flaps (0.099%), 59 buttonholes (0.070%), 74 thin or irregular flaps (0.087%), and 10 free flaps (0.012%). There were 134 right eye complications and 122 left eye complications (P =.45). No patient developed an intraoperative flap complication in both eyes. A comparison of Hansatome and Automated Corneal Shaper microkeratomes was possible for the cases performed between December 1999 and May 2000: 46 of 28 201 Hansatome procedures (0.16%) had a complication versus 21 of 329 Automated Corneal Shaper procedures (6.38%). This difference was statistically significant (P <.005).

CONCLUSION

The incidence of intraoperative flap complications during LASIK was acceptably small. The overall complication rate was similar in both eyes. The Hansatome was associated with a lower complication rate than the Automated Corneal Shaper.

Evaluation of a microkeratome-based limbal harvester device for limbal stem cell transplantation

PURPOSE

To assess the cut quality and reproducibility using a novel microkeratome-based limbal harvester.

METHODS

An enlarged microkeratome head and stainless steel blades were coupled with a nitrogen gas-driven turbine (15,000 blade oscillations/min) of a microkeratome. A large, 16-mm-diameter suction ring was attached to the globe. A lamellar sclerokeratectomy using head depths of 170 and 200 microm was performed in human donor research eyes. Obtained lenticule thickness was measured by ultrasound pachymetry and the bed size by planimetry. Histologic and scanning electron microscopy (SEM) analyses of the samples were performed.

RESULTS

Central lenticule thickness was 294 microm (standard deviation [SD] 37) for the 170 head and 277 microm (SD 91) for the 200 head (p = 0.720). Lenticule diameter was larger in the horizontal meridian using the 170 head (12.8 mm [SD 0.8] vs. 11.9 mm [SD 0.7], p = 0.028), but similar in vertical meridian (12.0 [SD 0.6] versus 11.4 mm [SD 0.6], p = 0.093). Histology showed a multilayer epithelial cell pattern at the lenticule periphery. The SEM showed a smooth cut surface in both the stromal bed and the lenticule.

CONCLUSION

Cut reproducibility and quality are similar to those found using standard microkeratomes for corneal lamellar cuts. This system ensures, in a straightforward way, the presence of epithelial cells in the edges of a mechanical sclerokeratectomy for limbal stem cell transplantation.

Laser in situ keratomileusis for myopia and astigmatism: safety and efficacy: a report by the American Academy of Ophthalmology

OBJECTIVE

This document describes laser in situ keratomileusis (LASIK) for myopia and astigmatism and examines the evidence to answer key questions about the efficacy and safety of the procedure.

METHODS

A literature search conducted for the years 1968 to 2000 retrieved 486 citations and an update search conducted in June 2001 yielded an additional 243 articles. The panel members reviewed 160 of these articles and selected 47 for the panel methodologist to review and rate according to the strength of evidence. A Level I rating is assigned to properly conducted, well-designed, randomized clinical trials; a Level II rating is assigned to well-designed cohort and case-control studies; and a Level III rating is assigned to case series and poorly designed prospective and retrospective studies, including case-control studies.

RESULTS

The assessment describes randomized controlled trials published in 1997 or later (Level I evidence) and more recent comparative and noncomparative case series (Level II and Level III evidence), focusing on results for safety and effectiveness. It is difficult to extrapolate results from these studies that are comparable to current practices with the most recent generation lasers because of the rapid evolution of LASIK technology and techniques. It is also difficult to compare studies because of variations in the range of preoperative myopia, follow-up periods, lasers, nomograms, microkeratomes and techniques, the time frame of the study, and the investigators' experience.

CONCLUSIONS

For low to moderate myopia, results from studies in the literature have shown that LASIK is effective and predictable in terms of obtaining very good to excellent uncorrected visual acuity and that it is safe in terms of minimal loss of visual acuity. For moderate to high myopia (>6.0 D), the results are more variable, given the wide range of preoperative myopia. The results are similar for treated eyes with mild to moderate degrees of astigmatism (<2.0 D). Serious adverse complications leading to significant permanent visual loss such as infections and corneal ectasia probably occur rarely in LASIK procedures; however, side effects such as dry eyes, night time starbursts, and reduced contrast sensitivity occur relatively frequently. There were insufficient data in prospective, comparative trials to describe the relative advantages and disadvantages of different lasers or nomograms.

Posterior corneal curvature changes after myopic laser in situ keratomileusis

OBJECTIVE

To assess the posterior corneal power and asphericity changes after myopic laser in situ keratomileusis (LASIK) and to correlate these changes with the amount of correction and the residual stromal bed thickness.

DESIGN

Prospective nonrandomized (self-controlled) comparative study.

PARTICIPANTS

Fifty-seven eyes of 14 women and 15 men, mean age at the time of surgery 33 +/- 9 (range, 19-53) years with a spherical equivalent (SEQ) of -1.00 to -15.50 (mean, -5.07 +/- 2.81) diopters (DI).

INTERVENTION

All procedures were performed with the Keratom II Coherent-Schwind excimer laser and and the Moria Model One microkeratome (150-microm head). Subjective refractometry, Orbscan slit scanning corneal topography analysis and pachymetry were performed before and 3 months after LASIK for myopia (n=35, -1.00 to -15.50 D, mean -4.75 +/- -3.07 D) or myopic astigmatism (n=22, sphere 0.00 to -9.75 D, mean -4.75 +/- 2.36 D; cylinder -0.75 to -3.50 D, mean -1.68 +/- 0.86 D). Intended ablation depth ranged from 12 to 108 (mean, 48 +/- 22) microm. Topographic raw data were decomposed into a set of Zernike polynomials as published in detail previously, and parameters potentially indicative for detection of a "mild keratectasia" were derived.

MAIN OUTCOME MEASURES

Posterior central corneal power and asphericity before and after LASIK were compared, and changes of these variables were correlated with the SEQ change (deltaSEQ)and the residual corneal bed thickness RBT).

RESULTS

The mean RBT after LASIK was 280 +/- 42 microm. Overall, change of posterior power (-6.28 +/- 0.22 D/ -6.39 +/- 0.23 D, P=0.02) was statistically significant and change of asphericity (0.98 +/-0.07/1.14 +/- -.20, P<0.0001) was highly significant. In eyes with RBT < or =250 microm, the average change of posterior central power (-0.20 +/- 0.10 D vs. -0.08 +/- 0.18 D) was significantly greater than in eyes with RBT >250 microm (P=0.003). The change of posterior corneal power correlated significantly with deltaSEQ (P=0.004) and the RBT (P=0.002).

CONCLUSIONS

Increased negative keratometric diopters and oblate asphericity of the posterior corneal curvature suggest that mild "keratectesia" of the cornea may be common early after LASIK. Further stuudies with longer follow-up are required to clarify whether this biomechanical deformation is progressive and whether a residual bed thickness of >250 microm can completely prevent it.

Reproducibility of corneal flap thickness in laser in situ keratomileusis using the Hansatome microkeratome

PURPOSE

To evaluate the reproducibility of flap thickness during laser in situ keratomileusis (LASIK) and to analyze the effect of preoperative central corneal thickness and corneal keratometric power on flap thickness.

SETTING

Department of Ophthalmology, Cerrahpasa Medical School, Istanbul, Turkey.

METHODS

One hundred forty eyes with a mean preoperative pachymetry of 554.4 microm +/- 36.3 (SD) and a mean keratometry of 43.5 +/- 1.9 diopters had LASIK using the Hansatome automated microkeratome (Bausch & Lomb Surgical) and a 193 nm argon-fluoride excimer laser (Summit SVS Apex Plus). The 180 microm microkeratome plate was used in all procedures. Corneal thickness was measured with an ultrasonic pachymeter (Advent, Mentor O&O Inc.) before and during the flap procedure, and the difference was taken as flap thickness. The data were analyzed using a 1-tailed t test and Pearson correlation coefficient.

RESULTS

The mean flap thickness was 120. 8 +/- 26.3 microm. There was a low correlation between baseline central corneal thickness and corneal flap thickness (P =.6, r = 0. 046). There was no correlation between preoperative keratometry and flap thickness (P =.01, r = 0.203).

CONCLUSIONS

The Hansatome microkeratome does not always produce a corneal flap of the intended thickness. Factors other than keratometry and pachymetry must affect flap thickness.