Acceleration of curing of resin composite at the bottom surface using slow-start curing methods

Influence of the Polymerization Modes on the Methacrylic Acid Release from Dental Light-Cured Materials-In Vitro Study

The study focuses on the problem of lowering the pH around a composite filling concerning the polymerization modes and methacrylic acid release, which may affect not only the oral health but also the whole organism. A total of 90 specimens (30 of each: Filtek Bulk Fill, Evetric and Riva LC) were placed in 90 sterile hermetic polyethene containers with saline and incubated at 37 °C. Ten samples of each material were light-cured for 40 s with one of the three curing modes: full power mode (FPM), ramping mode (RM) and pulse mode (PM). The pH and methacrylic acid release evaluation were performed at the following time points: after 2 h and after 3, 7, 21 and 42 days from the specimen preparation. Regardless of light-curing mode, all used materials were characterized by a gradual elevation in methacrylic acid concentration. Only for Filtek Bulk Fill, increased methacrylic acid release was closely associated with lower pH. The choice of the polymerization mode has no significant influence on the methacrylic acid release. However, further research about composite light-curing is necessary to create the procedure algorithm, reducing the local and systemic complications associated with composite fillings.

Effects of C-factor on dentin bonding using various adhesive systems

Aims and Background

This study evaluated the effect of C-factor on the bond strength of a resin composite to floor and wall dentin using various adhesive systems.

Materials and Methods

Four dentin substrates (flat wall, flat floor, cavity wall, or cavity floor) were prepared on human molars. Each specimen was restored with one of three adhesives; Clearfil SE Bond, Single Bond, or Clearfil tri-S Bond followed by buildup or filling using Z100 resin composite. The specimen was cut perpendicular to the bonded surface parallel to the floor or wall to obtain beams after light curing at 24,000 mJ/cm². The microtensile bond strength to wall specimens or the cavity floor was determined. Data were analyzed.

Results

All adhesive systems exhibited the highest bond strength to flat wall group (p < 0.05). The bond strength to the cavity group was significantly lower than that to the respective flat group regardless of the bonding system (p < 0.05). There was no significant difference in bond strength with Clearfil SE Bond and Clearfil tri-S Bond between the cavity wall and cavity floor (p > 0.05).

Conclusion

The findings suggested that the strength of bonding to the cavity floor and cavity wall was affected by C-factor regardless of the adhesive system. Bonding to flat wall was higher than flat floor regardless of the adhesive system. Self-etching system provided uniform bond to the cavity wall and cavity floor dentin. However, total etching system reduced bond to the cavity floor than to the cavity wall.

The Effect of Irradiance on the Degree of Conversion and Volumetric Polymerization Shrinkage of Different Bulk-Fill Resin-Based Composites: An In Vitro Study

Objective  The influence of different light-emitting diode (LED) curing light intensities on the degree of conversion (DC) and volumetric polymerization shrinkage (VPS) of bulk-fill resin-based composite (RBC) restorative materials was evaluated.

Materials and Methods  Twenty-four specimens of each RBC material (Filtek one bulk-fill posterior, Reveal HD Bulk, Tetric N-Ceram, and Filtek Z350) were prepared. The RBCs were shaped in molds and cured using an LED curing light unit at high-intensity (1,200 mW/cm ² ) for 20 seconds and low-intensity (650 mW/cm ² ) for 40 seconds Fourier-transform infrared (FTIR) spectroscopy was used to determine the DC and microcomputed tomography was used to evaluate VPS. Data were analyzed using one- and two-way ANOVA, independent t -test, and Tukey’s and Scheffe’s post hoc multiple comparison tests.

Results  With high-intensity curing light, Reveal HD showed the highest DC (85.689 ± 6.811%) and Tetric N-Ceram the lowest (52.60 ± 9.38%). There was no statistical difference in VPS when using high- or low-intensity curing light. The highest VPS was observed for Reveal HD (2.834–3.193%); there was no statistical difference ( p > 0.05) among the other RBCs.

Conclusion  Curing light intensities do not significantly influence the VPS of RBC materials. Reveal HD bulk cured with high-intensity light had the highest DC.

µCT-3D visualization analysis of resin composite polymerization and dye penetration test of composite adaptation

This study evaluated the effects of the light curing methods and resin composite composition on composite polymerization contraction behavior and resin composite adaptation to the cavity wall using μCT-3D visualization analysis and dye penetration test. Cylindrical cavities were restored using Clearfil tri-S Bond ND Quick adhesive and filled with Clearfil AP-X or Clearfil Photo Bright composite. The composites were cured using the conventional or the slow-start curing method. The light-cured resin composite, which had increased contrast ratio during polymerization, improved adaptation to the cavity wall using the slow-start curing method. In the μCT-3D visualization method, the slow-start curing method reduced polymerization shrinkage volume of resin composite restoration to half of that produced by the conventional curing method in the cavity with adhesive for both composites. μCT-3D visualization method can be used to detect and analyze resin composite polymerization contraction behavior and shrinkage volume as 3D image in the cavity.

Environmental SEM and dye penetration observation on resin-tooth interface using different light curing method

The aim of this study was the effects of different light curing methods on marginal sealing and resin composite adaptation to the cavity wall using the dye penetration test and environmental scanning electron microscope (SEM) observations. Cylindrical cavities were prepared on cervical regions. The teeth were restored with Clearfil Liner Bond 2 V adhesive and filled with Clearfil Photo Bright or Palfique Estelite resin composites. These resins were cured with a conventional light-curing method or a slow-start curing method. After thermal cycling, the specimens were subjected to the dye penetration test to evaluate marginal sealing and adaptation of the resin composites to the cavity walls. These resin-tooth interfaces were then observed using environmental SEM. The light-cured resin composite, which exhibited increased contrast ratios during polymerization, suggests high compensation for polymerization stress using the slow-start curing method. There was a high correlation between dye penetration test and environmental SEM observation.

Effects of light curing method and resin composite composition on composite adaptation to the cavity wall

This study aimed to evaluate the effects of the light curing method and resin composite composition on marginal sealing and resin composite adaptation to the cavity wall. Cylindrical cavities were prepared on the buccal or lingual cervical regions. The teeth were restored using Clearfil Liner Bond 2V adhesive system and filled with Clearfil Photo Bright or Palfique Estelite resin composite. The resins were cured using the conventional or slow-start light curing method. After thermal cycling, the specimens were subjected to a dye penetration test. The slow-start curing method showed better resin composite adaptation to the cavity wall for both composites. Furthermore, the slow-start curing method resulted in significantly improved dentin marginal sealing compared with the conventional method for Clearfil Photo Bright. The light-cured resin composite, which exhibited increased contrast ratios duringpolymerization, seems to suggest high compensation for polymerization contraction stress when using the slow-start curing method.