µCT-3D visualization analysis of resin composite polymerization and dye penetration test of composite adaptation

Dental Luting Cements: An Updated Comprehensive Review

The cementation of indirect restoration is one of the most important steps in prosthetic and restorative dentistry. Cementation aims to bond the prosthetic restoration to the prepared enamel or enamel and dentine. Successful cementation protocols prevent biofilm formation at the margin between tooth and restoration and minimize mechanical and biological complications. With the advancements in dental cements, they have been modified to be versatile in terms of handling, curing, and bond strengths. This review presents updates on dental cements, focusing on the composition, properties, advantages, limitations, and indications of the various cements available. Currently, dental restorations are made from various biomaterials, and depending on each clinical case, an appropriate luting material will be selected. There is no luting material that can be universally used. Therefore, it is important to distinguish the physical, mechanical, and biological properties of luting materials in order to identify the best options for each case. Nowadays, the most commonly used dental cements are glass-ionomer and resin cement. The type, shade, thickness of resin cement and the shade of the ceramic, all together, have a tangible influence on the final restoration color. Surface treatments of the restoration increase the microtensile bond strength. Hence, the proper surface treatment protocol of both the substrate and restoration surfaces is needed before cementation. Additionally, the manufacturer's instructions for the thin cement-layer thickness are important for the long-term success of the restoration.

Optical comparison between micro-CT and OCT in imaging of marginal composite adaptation: Observational study

Dental composite is the most used aesthetic restorative biomaterial worldwide. However, it undergoes polymerisation shrinkage that could lead to loss of the interfacial seal between tooth and resin in some circumstances. This demands high-resolution imaging technologies to detect these defects. This study carried out a comparison between microcomputed tomography (micro-CT; Shimadzu, Japan) and swept-source optical coherence tomography (SS-OCT; Santec, Japan) in the detection of marginal adaptation defects at the tooth-resin interface. Unlike in micro-CT, it was possible to outline interfacial gaps along with tooth-resin interfaces with SS-OCT, which was attributed to the Fresnel diffraction of light. This in vitro comparison demonstrates SS-OCT has great potential in dental imaging to effectively assess dental composite adaptation and marginal defects when high resolution is desired in real time. LAY DESCRIPTION: Detection of tooth-colored restoration defects had been assessed by different radiographic methods. However, most of these methods are either invasive or suffer from low-resolution. In this study, a comparison has been carried out between two different high-resolution imaging systems; microcomputed tomography and optical coherence tomography, to explore their potentials in detecting restorations defects. The results showed optical coherence tomography has a great accuracy in locating the underlying defects when the obtained images were validated against confocal laser scanning microscopy images.

Location of Tensile Damage Source of Carbon Fiber Braided Composites Based on Two-Step Method

Acoustic emission (AE) source localization is one of the important purposes of nondestructive testing. The localization accuracy reflects the degree of coincidence between the identified location and the actual damage location. However, the anisotropy of carbon fiber three-dimensional braided composites will have a great impact on the accuracy of AE source location. In order to solve this problem, the time-frequency domain characteristics of AE signals in a carbon fiber braided composite tensile test were analyzed by Hilbert–Huang transform (HHT), and the corresponding relationship between damage modes and AE signals was established. Then, according to the time-frequency characteristics of HHT of tensile acoustic emission signals, the two-step method was used to locate the damage source. In the first step, the sound velocity was compensated by combining the time-frequency analysis results with the anisotropy of the experimental specimens, and the four-point circular arc method was used to locate the initial position. In the second step, there is an improvement of the Drosophila optimization algorithm, using the ergodicity of the chaotic algorithm and congestion adjustment mechanism in the fish swarm algorithm. The smoothing parameters and function construction in the probabilistic neural network were optimized, the number of iterations was reduced, the location accuracy was improved, and the damage mode of composite materials was obtained. Then, the damage location was obtained to achieve the purpose of locating the damage source.

The effect of aging methods on the fracture toughness and physical stability of an oxirane/acrylate, ormocer, and Bis-GMA-based resin composites

PURPOSE

To determine the effect of aging methods on the fracture toughness of a conventional Bis-GMA-based resin composite (Filtek Supreme), an ormocer-based resin composite (Admira), and an experimental hydrophobic oxirane/acrylate interpenetrating network resin system (OASys)-based composite.

METHODS

A 25 × 5 × 2.8-mm stainless-steel mold with 2.5 mm single-edge center notch, following ASTM standards [E399-90], was used to fabricate 135 specimens (n = 15) of the composite materials and randomly distributed into groups. For the baseline group, specimens were fabricated and then tested after 24-h storage in water. For the biofilm challenge, specimens were randomly placed in a six-well tissue culture plate and kept at 37 °C with bacterial growth media (Brain Heart Infusion (BHI); Streptococcus mutans) changed daily for 15 days. For the water storage challenge, specimens were kept in 5 ml of deionized distilled autoclaved water for 30 days at 37 °C. μCT evaluation by scanning the specimens was performed before and after the proposed challenge. Fracture toughness (K_Ic) testing was carried out following the challenges.

RESULTS

μCT surface area and volume analyses showed no significant changes regardless of the materials tested or the challenge. Filtek and Admira fracture toughness was significantly lower after the biofilm and water storage challenges. OASys mean fracture toughness values after water aging were significantly higher than that of baseline. Toughness values for OASys composites after biofilm aging were not statistically different when compared to either water or baseline values.

CONCLUSION

The fracture toughness of Bis-GMA and ormocer-based dental resin composites significantly decreased under water and bacterial biofilm assault. However, such degradation in fracture toughness was not visible in OASys-based composites.

CLINICAL SIGNIFICANCE

Current commercial dental composites are affected by the oral environment, which might contribute to the long-term performance of these materials.