Effect of smear layer and surface roughness on resin-dentin bond strength of self-etching adhesives

Dentin Bonding Durability of Four Different Recently Introduced Self-Etch Adhesives

The objectives of this study were to evaluate the bonding durability of four different self-etch adhesives to dentin after 24 h and thermal cycling (TC) and to measure the degree of polymerization conversion (DC) in situ. Two-step self-etch adhesives, Clearfil SE Bond 2 (SE2, Kuraray Noritake Dental) and G2-Bond Universal (G2B, GC), and one-step self-etch adhesives, Scotchbond™ Universal Plus Adhesive (SBU, 3M ESPE) and Clearfil Universal Bond Quick (UBQ, Kuraray Noritake Dental), were used. The labial surfaces of bovine teeth were ground to create flat dentin surfaces. The adhesives were applied according to the manufacturers' instructions. After resin composite buildup and 24 h water storage, the specimens were sectioned into beams and all groups were subjected to thermal stress for 0, 10,000 (10k), or 20,000 (20k) cycles followed by micro-tensile bond strength (µTBS) testing. In situ DC was investigated with a laser Raman microscope. The µTBS data were statistically analyzed and subjected to a Weibull analysis. The different groups were compared at the characteristic strength (63.2% probability of failure) (α = 0.05). Two-Way ANOVA was used to show the effect of different adhesives and thermal cycling on the mean DC% followed by Tukey's multiple comparison post hoc test. G2B/TC10k resulted in a significant increase in the µTBS compared to TC0. SBU/TC20k showed significantly higher µTBS compared to TC0. For comparison between different tested adhesives, SBU showed a significantly lower µTBS compared to G2B after TC10k. G2B and SBU showed a greater number of adhesive failures after TC. Mean DC% was different for each adhesive. The newly developed MDP- and HEMA-free 2-SEA showed similar bonding performance with the gold-standard 2-SEA. However, there is still room for further improvement in terms of SEAs.

Sealing ability of various endodontic sealers with or without ethylenediaminetetraacetic acid (EDTA) treatment on bovine root canal

This study investigated the wettability and consistency of various endodontic sealers, both inorganic and organic, and evaluated their sealing ability of root canals using the single-cone obturation technique, with and without ethylenediaminetetraacetic acid (EDTA) treatment. Bovine root canals were endodontically prepared and filled in preparation for the dye penetration test with toluidine blue solution. All sealers exhibited contact angles similar to or lower than dentin and displayed superior consistency. Among the sealers, organic sealers used without EDTA treatment showed reduced dye penetration compared to inorganic sealers. However, some inorganic and organic sealers showed dye penetration in the sealer and dentin of root canals subjected to EDTA treatment. In conclusion, the single-cone obturation technique, combined with these endodontic sealers, achieved close contact with root canal dentin due to their wettability and consistency. However, the sealing ability of certain sealers was influenced by EDTA treatment.

Effects of Nd:YAG laser irradiation at different energy densities on dentin bond durability under simulated pulpal pressure

OBJECTIVES

To evaluate the effects of Nd:YAG laser irradiation on the microstructures of dentin surfaces and the long-term bond strength of dentin under simulated pulpal pressure.

MATERIALS AND METHODS

Under simulated pulp pressure, 30 freshly extracted caries-free third molars were cut into 2-mm-thick dentin samples and then divided into five groups: the control and laser groups (93.3 J/cm2; 124.4 J/cm2; 155.5 J/cm2; 186.6 J/cm2). Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR), and Vickers hardness were used to analyze the surface morphology, composition, and mechanical properties of the dentin before and after laser irradiation. Another 80 caries-free third molars were removed and treated as described above, and the resin was bonded to the dentin surface with Single Bond Universal (SBU) adhesive in self-etch mode to make stick specimens. Microtensile bond strength (µTBS), confocal laser scanning microscopy (CLSM), and interfacial silver nanoleakage tests before and after 10,000 times thermocycling were then performed to analyze the bonding properties and interfacial durability of each group.

RESULTS

SEM observations revealed that the surfaces of all laser group specimens were rough with open dentin tubules. Laser irradiation altered the surface composition of dentin while removing some collagen fibers but did not affect its surface hardness or crystallographic characteristics. Furthermore, laser irradiation with an energy density of 124.4 J/cm2 significantly promoted the immediate and aging bond strengths and reduced nanoleakage compared to those of the control group.

CONCLUSIONS

Under simulated pulp pressure, Nd:YAG laser pretreatment altered the chemical composition of dentin and improved the immediate and long-term bond strength.

CLINICAL RELEVANCE

This study investigated the optimal parameters for Nd:YAG laser pretreatment of dentin, which has potential as a clinical method to strengthen bonding.

Effect of various Er:YAG laser conditioning energies on dentin surface: micromorphological investigation and dentin-resin shear bond strength test

The aim of this study is to assess the influence of various Er:YAG laser energies on dentin surface micromorphology and dentine-resin shear bond strength (SBS). Eighty dentin specimens were prepared and divided randomly into ten groups: control group (CG), phosphoric acid-etched group (AG), four laser-conditioned groups treated with various pulse energies of 40, 60, 80, and 100 mJ (L40, L60, L80, L100), and four laser-conditioned acid-etched groups (LA40, LA60, LA80, LA100). Two specimens from each group underwent scanning electron microscopy examination, while the remaining six were subjected to the dentin-resin SBS test. Statistical analyses included Welch's analysis of variance (ANOVA), followed by post hoc Tamhane's T2 multiple comparisons test, Pearson's correlation, and Fisher's exact test. Pulse energies of 60, 80, and 100 mJ fully exposed the dentin tubule orifices, although 100 mJ lead to microcracks. Laser-conditioned surfaces exhibited smaller tubule diameters compared to acid-etched surfaces, and tubule diameters positively correlated with dentin-resin SBS. Laser-conditioned groups showed lower SBS values, while laser-conditioned acid-etched groups demonstrated higher SBS values. No significant relationship was observed between dentin surface roughness and SBS. The range of laser energies used for dentin conditioning had limited effects on SBS or failure modes. Laser conditioning with energies ranging from 40 to 100 mJ effectively removes the smear layer from the dentin surface. However, to enhance dentin-resin bond strength, further acid etching of the laser-conditioned surface is necessary.

Effect of limonene associated with bioactive glass-ceramic on dentin/adhesive interface

This study evaluated the effect of pretreatment with limonene and/or biosilicate on the bond strength of a universal adhesive system in self-etch mode to dentin. Occlusal cavities were prepared in 80 human molars and the teeth were randomly allocated to one of four groups (n = 20), according to the pretreatment regimens applied before the adhesive. The pretreatments were (i) Control, no pretreatment, (ii) LIM, 0.5% limonene; (iii) Bio, 10% biosilicate; and (iv) LIMBio, LIM + Bio. After adhesive application and restoration, the specimens were sectioned into sticks, separated, and stored in distilled water at 37°C for 24 h or 6 months. Microtensile bond strength test was carried out and measurements were compared across pretreatment groups and storage times. Fracture patterns and adhesive interfaces were observed. Loss of dry mass was calculated (n = 10). There was no statistically significant difference in the bond strength between the groups and the most prevalent fracture pattern was the non-adhesive. LIM and LIMBio resulted in more open dentinal tubules. LIM and Bio, whether separate or combined, showed particles of those substances, which decreased in size and number after 6 months. All groups lost mass weight after treatment, with no statistically significant differences between them. Limonene and biosilicate pretreatment did not affect the bond strength to dentin of the universal adhesive system, but resulted in more non-adhesive fractures, even after 6 months.

Role of the smear layer in adhesive dentistry and the clinical applications to improve bonding performance

Currently, dental adhesives can be divided into two systems; a smear layer-removal approach with etch-and-rinse adhesives or a smear layer-modified approach with self-etching adhesives. After phosphoric acid etching, the smear layer is completely removed. More attention is, however, required when using self-etching adhesives. The smear layer is partially demineralized by the weak acidic monomer and subsequently incorporated into the hybrid layer. Therefore, the characteristics of the smear layer play an important role on the bonding performance of self-etching adhesives. Such characteristics, for instance, smear layer thickness and smear layer density, are influenced by many factors, e.g., instruments used for dentin surface preparation, cutting speed, and the abrasive particle size of the cutting instruments. This review discusses the contributing factors that affect the smear layer characteristics, and the influence of the smear layer on the bonding performance of dental adhesives. Also, the application techniques regarding how to improve the bonding performance of self-etching adhesives - the smear layer removal by using chemical agents, or the modification of the adhesive application procedures - are provided.

Delayed light activation of resin composite affects the bond strength of adhesives under dynamic simulated pulpal pressure

OBJECTIVE

To evaluate the effect of a time delay before the light activation of resin composite on the microtensile bond strength (µTBS) of self-etch adhesives under dynamic simulated pulpal pressure.

MATERIALS AND METHODS

One hundred twenty crown segments were prepared from human third molars. Dentin surfaces were prepared with coarse diamond burs and connected to a dynamic pulpal pressure device. The self-etch adhesives used were Clearfil SE Bond (CSE), G2-Bond Universal (G2B), Clearfil Universal Bond Quick (CBQ), and G-Premio Bond (GPB). Each adhesive was divided into 3 subgroups: immediate light activation of resin composite (T₀), delayed light activation for 150 s (T₁), and 300 s (T₂). The µTBS data were obtained after 24-h water storage. Scanning electron microscopy was used to evaluate the nanoleakage at the resin-dentin surface. The µTBS data were analyzed using two-way ANOVA and Duncan's multiple comparisons.

RESULTS

All adhesives demonstrated a significant reduction in µTBS at T₂, except for CBQ where the bond strength was not affected by the delayed light activation times. The two-step self-etch adhesives (CSE and G2B) demonstrated higher bond strength than the one-step adhesives at all conditions. Nanoleakage was observed in all adhesives at T₂; however, nanoleakage was detected only in CBQ and GPB at T₁.

CONCLUSIONS

Delayed light activation of resin composite adversely affected the dentin bond strength of self-etch adhesives. Two-step self-etch adhesives had better bonding performance than one-step self-etch adhesives.

CLINICAL RELEVANCE

After adhesive application, resin composite should be adapted and cured as soon as possible.

Bonding of universal adhesives to bur-cut dentin: Effect of double application and dentin moisture level

This study investigated how the double application of adhesives and dentin moisture level influence the microtensile bond strength (µTBS) of universal adhesives containing different hydrophilic monomers to bur-cut dentin. Four universal adhesives (Scotchbond Universal, Clearfil Universal Bond Quick, Prime&Bond Universal, BeautiBond Universal) were applied to wet and dry bur-cut dentin either in one or two layers. The µTBS test was performed after 25,000 thermal cycles, and scanning electron microscopy was used for the analysis of failure mode and interfacial ultrastructure. Double application significantly improved µTBS on wet dentin (p<0.001), but the effect was not significant on dry dentin (p>0.050). Double application also enhanced the formation of resin tags and limited voids within the adhesive layer of BeautiBond Universal. Dentin moisture had a significant effect on µTBS only if the adhesives were applied in a single layer (p=0.007). Except for Prime&Bond Universal, the tested universal adhesives performed better on dry dentin.

The Effect of Different Abrasives on the Shear Bond Strength of Adhesive Resin Cements to Dentin

Aim:

The aim of this study was to evaluate the influence of dentin surface preparation with coarse diamond, extra-fine diamond, and polishing discs on the shear bond strength (SBS) of two resin cements (RCs) to dentin.

Materials and Methods:

Sixty-six recently extracted human mandibular third molar teeth that were free of cracks, caries, or restorations were collected. Sixty teeth were used for the SBS test. The occlusal part of the crowns was cut to expose mid-coronal dentin. The teeth were divided into three dentin preparation groups: coarse diamond (Meisinger, Germany), extra-fine diamond, and polishing discs (SofLex, 3MESPE, USA), and further conventional RC combined with a self-etch adhesive (Panavia F2.0/ED Primer II, Kuraray, Japan) or self-adhesive RC (Maxcem Elite, Kerr, USA) subgroups ( n = 10). Sixty composite resin blocks were prepared (diameter: 3 mm, height: 4 mm) and bonded to the teeth according to the groups. The SBS test was performed with a universal testing device. Six teeth were used for the observation of prepared dentin surfaces and the resin–cement dentin interfaces using field emission scanning electron microscopy (Mira 3 XMU, Tescan). Statistical analyses were performed using the Mann–Whitney U and Kruskal–Wallis tests ( P < .05).

Results:

Panavia F2.0/ED Primer II exhibited significantly higher SBS values for coarse and extra-fine diamond than for the polishing discs ( P <.05). Regarding Maxcem Elite, no significant difference was observed for the preparation methods ( P > .05). Panavia F2.0/ED Primer II had higher bond strength than Maxcem Elite for the dentin surface prepared with the coarse diamond ( P <.05). The differences were not significant for the extra-fine diamond and the polishing disc groups ( P > .05).

Conclusion:

The use of polishing discs did not increase the SBS of the RCs to the dentin.

Shear bond strength of resin bonded zirconia and lithium disilicate - effect of surface treatment of ceramics and dentin

Objectives:The purpose of the study was to investigate the effect of ceramic surface pretreatment, effect of resin cement and dentin surface roughness on shear bond strength.

Methodology: Zirconia rods (n = 140) were randomly assigned to air born particle abrasion with aluminum oxide (Al₂O₃) or hot etching with potassium hydrogen difluoride (KHF₂). Lithium disilicate rods (LDS; n = 50) etched with hydrofluoric acid served as reference material. In Part 1 of the study, ceramic rods were cemented to bovine dentin using 5 dual-polymerizing resin cements (Variolink Esthetic, Multilink Automix (Ivoclar Vivadent), Duo-Link (BISCO Dental), Panavia F2.0 (Kuraray Dental), RelyX Unicem (3 M)). Shear bond strength was tested and fracture morphology determined. In Part 2 of the study, test groups with the highest frequency of adhesive fractures between cement and dentin were selected for further bond strength testing with different surface roughness of dentin; ground with P1200 or P80 silicon carbide paper. Dentin samples were fractured vertically to the cemented surface and the adherence between cement and dentin was studied.

Results: The results of Part 1 showed that hot etching of zirconia significantly improved bond strength to Duo-Link cement. In Part 2, RelyX Unicem showed significantly higher bond strength to P1200 compared to P80 ground dentin. For Variolink Esthetic, bond strengths to P1200 and P80 ground dentin were similar. Adhesive fracture between cement and dentin dominated.

Conclusions: A smooth dentin surface (P1200) improved bond strength to RelyX Unicem. Surface roughness was not important for Variolink Esthetic.

Physicochemical Properties of Dentine Subjected to Microabrasive Blasting and Its Influence on Bonding to Self-Adhesive Prosthetic Cement in Shear Bond Strength Test: An In Vitro Study

The aim of this in vitro study was to assess the influence of microabrasive blasting on the physicochemical properties of dentine and shear bond strength (SBS) of self-adhesive resin cement (Maxcem Elite, Kerr, Orange, CA, USA) bonded to the dentine surface. Ninety cylindrical specimens with exposed dentine of human teeth were prepared and divided into three randomized, parallel sample sets A, B, and C. Groups B and C were subjected to abrasive blasting using a micro-sandblasting device (Microetcher IIa, Danville Materials, Carlsbad, CA, USA) with two gradations of Al₂O₃ abrasives (Group B, abrasion with a gradation of 50 μm; group C, abrasion with a gradation of 27 μm). SEM imaging, profilometry, chemical composition analysis, contact angle measurements, surface free energy, and SBS tests were performed. The resulting data were statistically analyzed using the Statistica software (ver. 13.3, Tibco Software Inc., Palo Alto, CA, USA). Microabrasive blasting caused changes in surface topography, structural features, and the connection strength between the dentin surface and self-adhesive prosthetic cement. Air microabrasion through the multifactorial positive reorganization of the treated surface of dentine is recommended as a pretreatment method in fixed prosthodontics adhesive cementation protocols.

Effects of dentin surface preparations on bonding of self-etching adhesives under simulated pulpal pressure

Objectives

This study evaluated the effects of different smear layer preparations on the dentin permeability and microtensile bond strength (µTBS) of 2 self-etching adhesives (Clearfil SE Bond [CSE] and Clearfil Tri-S Bond Universal [CTS]) under dynamic pulpal pressure.

Materials and Methods

Human third molars were cut into crown segments. The dentin surfaces were prepared using 4 armamentaria: 600-grit SiC paper, coarse diamond burs, superfine diamond burs, and carbide burs. The pulp chamber of each crown segment was connected to a dynamic intra-pulpal pressure simulation apparatus, and the permeability test was done under a pressure of 15 cmH₂O. The relative permeability (%P) was evaluated on the smear layer-covered and bonded dentin surfaces. The teeth were bonded to either of the adhesives under pulpal pressure simulation, and cut into sticks after 24 hours water storage for the µTBS test. The resin-dentin interface and nanoleakage observations were performed using a scanning electron microscope. Statistical comparisons were done using analysis of variance and post hoc tests.

Results

Only the method of surface preparation had a significant effect on permeability (p < 0.05). The smear layers created by the carbide and superfine diamond burs yielded the lowest permeability. CSE demonstrated a higher µTBS, with these values in the superfine diamond and carbide bur groups being the highest. Microscopic evaluation of the resin-dentin interface revealed nanoleakage in the coarse diamond bur and SiC paper groups for both adhesives.

Conclusions

Superfine diamond and carbide burs can be recommended for dentin preparation with the use of 2-step CSE.

Chitosan improves the durability of resin-dentin interface with etch-and-rinse or self-etch adhesive systems

Degradation of the dentin-resin interface can occur due to hydrolysis of exposed collagen, resulting in reduced bond strength. This study assessed the effect of dentin treatment with chitosan combined with an etch-and-rinse or self-etch adhesive system on improvement of bond strength and preservation of the interface durability.

Effect of Pretreatment and Activation Mode on the Interfacial Adaptation of Nanoceramic Resin Inlay and Self-adhesive Resin Cement

OBJECTIVES

The first objective of this study was to determine if the luting material used for resin nanoceramic inlay affects interfacial adaptation. The second was to investigate whether pretreatment and the adhesive curing method before cementation affects interfacial adaptation. The final objective was to compare activation modes of luting material.

METHODS

Class I cavities were prepared on extracted human third molars. Resin nanoceramic inlays were fabricated using Lava Ultimate CAD/CAM block (3 M). For the control groups, inlays were cemented using Panavia V5 (Kuraray Noritake). For the experimental groups, teeth were randomly divided into five experimental groups with four subgroups using different self-adhesive cements (SACs). Cement in Group I was dual-cured without pretreatment. In Group II, the cement was dual-cured after polyacrylic acid treatment of the tooth cavity. In Groups III and IV, the cement was dual-cured after universal dentin adhesive treatment with pre-cure and co-cure methods. In Group V, the inlay was cemented in self-cure mode. After thermocycling, interfacial adaptation at the inlay-tooth interface was measured using swept-source optical coherence tomography (SS-OCT) imaging. Finally, polymerization shrinkage strain of the luting material was measured and compared.

RESULTS

Interfacial adaptation differed depending on the luting material. After application of a universal adhesive, some subgroups showed improved interfacial adaptation. Interfacial adaptation and polymerization shrinkage strain differed significantly depending on activation mode.

SIGNIFICANCE

Interfacial adaptation for a resin nanoceramic inlay can differ according to the type of SAC and activation mode. For some SACs, application of a universal adhesive before cementation improves interfacial adaptation.

Influence of different irrigation protocols on microhardness and flexural strength values of young and aged crown dentin

OBJECTIVE

To investigate the effect of different irrigation protocols on microhardness (MH) and flexural strength (FS) values of young and aged crown dentin.

BACKGROUND

In addition to ageing, root canal irrigation might also affect the mechanical properties of coronal dentin walls.

MATERIALS AND METHODS

One hundred and twenty dentin bars (2 mm × 2 mm × 8 mm) were obtained from the crowns of extracted, non-caries, human molars of young and older patients (n = 60 bars; average patient ages: 16.7 and 65.4, respectively). Subgroups were formed as follows: 2.5%NaOCl(sodium hypochlorite)+5%EDTA(ethylenediaminetetraacetic acid), 2.5%NaOCl + 15%EDTA, 2.5%NaOCl, 5%EDTA, 15%EDTA and Saline. NaOCl and saline were used for 20 minutes and EDTA solutions for 1 minute. MH values of each sample were measured before and after the irrigation protocols. The same samples were also submitted for FS analysis. The data were statistically analysed.

RESULTS

Young samples had lower MH values at pre- and post-treatment compared to aged samples (P < .05). A significant decrease was observed in MH values of aged samples exposed to 2.5%NaOCl and both NaOCl + EDTA combinations (P < .05). FS values of the young saline-treated group were statistically higher than aged ones (P < .05). Both NaOCl + EDTA combinations caused a significant decrease in FS values of young samples compared to saline (P < .05).

CONCLUSION

Ageing has a significant effect on the MH and FS values of crown dentin samples. 5% EDTA solutions revealed similar results to 15%EDTA regarding MH and FS values of crown dentin in both age groups. The NaOCl + EDTA combination had a prominent effect than EDTA alone, on MH values of young-, and FS values of aged dentin samples.