Comparison of the vertical bone defect healing abilities of carbonate apatite, β-tricalcium phosphate, hydroxyapatite and bovine-derived heterogeneous bone

Retention of strength and ion release of some restorative materials

This study aimed to investigate the retention of strength in accelerated aging condition and ion release from an experimental fiber-reinforced bioactive flowable composite resin (Bio-SFRC), comparing it with various commercially available ion-releasing materials. The flexural strength of Bio-SFRC and other materials (Biodentine, TheraCal LC, Fuji II LC and Surefil one) was evaluated (n = 8) before and after hydrothermal accelerated aging. Ion concentrations of silica and phosphorus were measured after 1, 2, 3, 4, 7, 10, 14, and 21 days of specimen immersion in simulated body fluids (SBF) using UV-Vis spectrometry. In addition, ion release and pH change were studied in a continuous dynamic system in SBF over a period of 72 h. SEM and EDS were used to evaluate the microstructure on the top surface of the materials after SBF immersion. Data were statistically analyzed using variance ANOVA analysis (p = 0.05). Bio-SFRC showed higher flexural strength before (134.9 MPa) and after (63.1 MPa) hydrothermal aging compared to other tested materials (p < 0.05). Flexural strength significantly decreased after aging (p < 0.05) except for Fuji II LC which showed no significant differences. Ion release data showed that experimental Bio-SFRC slowly released phosphate ions. Biodentine and TheraCal LC had the strongest ability to form calcium phosphate precipitation on the material surface. Phosphate ion release cannot be detected clearly from these materials. Surefil one and Fuji II LC were more stable materials without any observable ion release. The advantages of fiber containing structure and slow release of ions suggest that experimental Bio-SFRC is a promising bioactive material to provide ions for mineralization of surrounding tissues, and keeping the durability of the materials at higher level than that of other tested materials.

Fabrication and histological evaluation of a self-setting granular cement using calcium sulfate hemihydrate granules with different pore distribution

Granular type of bone substitutes is currently used in the field of dentistry to restore alveolar bone defects. However, the migration of the granules from the implantation site is still an unresolved issue. In this study, the feasibility to fabricate self-setting calcium sulfate hemihydrate (CSH) granules using different ranges of loading pressure: CSH(0), CSH(50), CSH(100), and CSH(150) was investigated with the hypothesis that CSH granules with reduced microporosity can inhibit the rapid dissolution rate of the calcium sulfate dihydrate (CSD) set blocks and induce bone regeneration. After 4 weeks of implantation, the granules were mostly replaced with new bone although no significant differences were observed. Nevertheless, the granules demonstrated the ability to set within the bone defect. It is therefore concluded that the setting ability of calcium sulfate can contribute to address the issue of migration of the granules and provide a useful guide for designing setting bone substitutes.

Combined Effects of Fibroblast Growth Factor-2 and Carbonate Apatite Granules on Periodontal Healing: An In Vivo and In Vitro Study

The aim of this study was to investigate in vivo and in vitro the effectiveness of the use of fibroblast growth factor (FGF)-2 with carbonate apatite (CO3Ap) on periodontal healing. Periodontal defects created in the maxillary first molars in rats were treated with FGF-2, CO3Ap, FGF-2 + CO3Ap or left unfilled. Healing was evaluated using microcomputed tomography, histological, and immunohistochemical analyses. In vitro experiments were performed to assess cellular behaviors and the expression of osteoblastic differentiation markers in MC3T3-E1 cells. At 4 weeks, the bone volume fraction in the FGF-2 + CO3Ap group was significantly greater than that in the CO3Ap group, but there was no significant difference from the FGF-2 group. The FGF-2 + CO3Ap group demonstrated greater new bone compared with the FGF-2 or CO3Ap group. The FGF-2 + CO3Ap group showed greater levels of osteocalcin-positive cells compared with the CO3Ap group, but there was no significant difference from the FGF-2 group. In vitro, the FGF-2 + CO3Ap group exhibited a greater extent of cell attachment and more elongated cells compared with the CO3Ap group. Compared with the CO3Ap group, the FGF-2 + CO3Ap group showed significantly higher viability/proliferation, but the expressions of Runx2 and Sp7 were reduced. The results indicated that the use of FGF-2 with CO3Ap enhanced healing in the periodontal defects. FGF-2 promoted cell attachment to and proliferation on CO3Ap and regulated osteoblastic differentiation, thereby contributing to novel bone formation.

Productizing Nano-Bioactive Glass-Based Bilayer Scaffolds: A Graft for Reconstruction of Mandibular and Femoral Bone Defects

This investigation aimed to construct a bilayer scaffold integrating alginate and gelatin with nanobioactive glass (BG), recognized for their efficacy in tissue regeneration and drug delivery. Scaffolds, namely, alginate/gelatin (AG), alginate-/actonel gelatin (AGD), alginate actenol/gelatin-45S5 BG (4AGD), and alginate-actonel/gelatin-59S BG (5AGD), were assembled using a cost-effective freeze-drying method, followed by detailed structural investigation via powder X-ray diffraction as well as morphological characterization using field emission scanning electron microscopy (FESEM). FESEM revealed a honeycomb-like morphology with distinct pore sizes for nutrient, oxygen, and drug transport. The scaffolds evidently exhibited hemocompatibility, high porosity, good swelling capacity, and biodegradability. In vitro studies demonstrated sustained drug release, particularly for scaffolds containing actonel. In vivo tests showed that the bilayer scaffold promoted new bone formation, surpassing the control group in bone area increase. The interaction of the scaffold with collagen and released ions improved the osteoblastic function and bone volume fraction. The findings suggest that this bilayer scaffold could be beneficial for treating critical-sized bone defects, especially in the mandibular and femoral regions.

Biological Properties and Medical Applications of Carbonate Apatite: A Systematic Review

Bone defects represent an everyday challenge for clinicians who work in the fields of orthopedic surgery, maxillofacial and oral surgery, otorhinolaryngology, and dental implantology. Various bone substitutes have been developed and utilized, according to the needs of bone reconstructive surgery. Carbonate apatite has gained popularity in recent years, due to its excellent tissue behavior and osteoconductive potential. This systematic review aims to evaluate the role of carbonate apatite in bone reconstructive surgery and tissue engineering, analyze its advantages and limitations, and suggest further directions for research and development. The Web of Science, PubMed, and Scopus electronic databases were searched for relevant review articles, published from January 2014 to 21 July 2023. The study was conducted in accordance with the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Eighteen studies were included in the present review. The biological properties and medical applications of carbonate apatite (CO3Ap) are discussed and evaluated. The majority of articles demonstrated that CO3Ap has excellent biocompatibility, resorbability, and osteoconductivity. Furthermore, it resembles bone tissue and causes minimal immunological reactions. Therefore, it may be successfully utilized in various medical applications, such as bone substitution, scaffolding, implant coating, drug delivery, and tissue engineering.

Preclinical evaluation of a new synthetic carbonate apatite bone substitute on periodontal regeneration in intrabony defects

OBJECTIVE

To evaluate the potential of a novel synthetic carbonate apatite bone substitute (CO3 Ap-BS) on periodontal regeneration.

BACKGROUND

The use of various synthetic bone substitutes as a monotherapy for periodontal regeneration mainly results in a reparative healing pattern. Since xenografts or allografts are not always accepted by patients for various reasons, a synthetic alternative would be desirable.

METHODS

Acute-type 3-wall intrabony defects were surgically created in 4 female beagle dogs. Defects were randomly allocated and filled with CO3 Ap-BS (test) and deproteinized bovine bone mineral (DBBM) or left empty (control). After 8 weeks, the retrieved specimens were scanned by micro-CT, and the percentages of new bone, bone substitute, and soft tissues were evaluated. Thereafter, the tissues were histologically and histometrically analyzed.

RESULTS

Healing was uneventful in all animals, and defects were present without any signs of adverse events. Formation of periodontal ligament and cementum occurred to varying extent in all groups without statistically significant differences between the groups. Residues of both bone substitutes were still present and showed integration into new bone. Histometry and micro-CT revealed that the total mineralized area or volume was higher with the use of CO3 Ap-BS compared to control (66.06 ± 9.34%, 36.11 ± 6.40%; p = .014, or 69.74 ± 2.95%, 42.68 ± 8.68%; p = .014). The percentage of bone substitute surface covered by new bone was higher for CO3 Ap-BS (47.22 ± 3.96%) than for DBBM (16.69 ± 5.66, p = .114).

CONCLUSIONS

CO3 Ap-BS and DBBM demonstrated similar effects on periodontal regeneration. However, away from the root surface, more new bone, total mineralized area/volume, and higher osteoconductivity were observed for the CO3 Ap-BS group compared to the DBBM group. These findings point to the potential of CO3 Ap-BS for periodontal and bone regeneration.

Comparison of Orthodontic Tooth Movement of Regenerated Bone Induced by Carbonated Hydroxyapatite or Deproteinized Bovine Bone Mineral in Beagle Dogs

Orthodontic treatments often involve tooth movement to improve dental alignment. In this study, we aimed to compare tooth movement in regenerated bone induced by two different bone fillers, carbonated hydroxyapatite (CAP) and deproteinized bovine bone mineral (DBBM). Four beagle dogs were used in this comparative study. The first, second, and fourth lower mandibular premolars (P1, P2, and P4) on both sides of the mouth were extracted, and CAP was implanted into the extraction site on the left side and DBBM into the right side. Following regenerative bone healing, orthodontic devices were attached to perform orthodontic tooth movement of the lower third mandibular premolar (P3) on both sides. X-ray examination, intraoral scan, and histological analysis were performed. The Mann-Whitney U test was used for statistical analysis, and p < 0.05 was considered significant. Bone regeneration and orthodontic tooth movement were observed in the CAP and DBBM groups. Histologically, normal periodontal tissue remodeling was observed on the compression and tension sides of CAP and DBBM. No statistical difference was observed in the number of osteoclasts around the periodontal ligament and the root resorption area. Orthodontic tooth movement of regenerated bone induced by CAP and DBBM was therefore achieved.

Clinical outcomes of periodontal regenerative therapy with carbonate apatite granules for treatments of intrabony defects, Class II and Class III furcation involvements: A 9-month prospective pilot clinical study

Introduction

Carbonated apatite (CO3Ap) has unique properties as an alloplastic bone substitute and has been reported the safety and efficacy for bone regeneration. However, no previous studies reported the clinical application of CO3Ap for periodontal regeneration therapy. The aim of this study was to evaluate the safety and efficacy of periodontal regeneration with CO3Ap in treating intrabony defects, Class II and Class III furcation involvement (FI).

Methods

A single-arm and single-center prospective pilot clinical study was performed to verify the safety and efficacy of CO3Ap in patients with periodontitis. A total of four patients with seven teeth, including three deep intrabony defects, two Class II FI, and two Class III FI, were treated with CO3Ap. The clinical parameters, including probing pocket depth (PPD), clinical attachment level (CAL), bleeding on probing (BOP), tooth mobility (Mo), Plaque index (PI), and Gingival index (GI) were evaluated at baseline, 6 months, and 9 months after the surgery. Radiographic analysis was conducted on images of dental X-ray and cone beam computed tomography (CBCT) at baseline and 9 months post-surgery.

Results

The postoperative healing in all cases was uneventful, with no abnormal bleeding, pain, or swelling. The mean PPD reduction and CAL gain were 5.0 ± 1.0 mm, 4.5 ± 0.7 mm, 1.5 ± 0.7 mm, and 4.7 ± 1.2 mm, 4.5 ± 0.7 mm, 0.0 mm for intrabony defect, Class II and Class III FI, respectively. According to radiographic analysis, linear bone height in intrabony defects and vertical subclassification of FI in Class II FI were improved.

Conclusions

The clinical application of CO3Ap for the treatment of intrabony defects and Class II FI could be effective for periodontal regeneration, although its efficacy in treating Class III FI might be limited. Despite the limitations of this study, the findings in this study suggested that CO3Ap has the potential to be a promising bone graft substitute for periodontal regeneration.

Carbonate apatite versus β-tricalcium phosphate for rat vertical bone augmentation: A comparison of bioresorbable bone substitutes using polytetrafluoroethylene tubes

This study radiologically and histologically compared two bioresorbable bone substitutes with different compositions carbonate apatite (Cytrans® Granules; CGs) and β-tricalcium phosphate (β-TCP) for vertical bone augmentation on a rat skull using a polytetrafluoroethylene (PTFE) tubes. This PTFE tube was placed at the center of the skull, fixed with Super Bond, and augmented with CGs or β-TCP granules. Specimens with surrounding tissue were harvested at 4, 8, and 12 weeks postoperatively, and radiological and histological evaluations were performed. The bone volume to total volume ratio (BV/TV) of the β-TCP-implanted group was markedly higher than that of the CG-implanted group at 4 and 12 weeks postoperatively. Compared to CGs, β-TCP exhibited the ability to form blood vessels into the graft material for a short period after transplantation, as well as an elevated production of collagen into β-TCP granules during the bone formation process.

Preclinical evaluation of the effect of periodontal regeneration by carbonate apatite in a canine one-wall intrabony defect model

Objective

This study aimed to histologically compare periodontal regeneration of one-wall intrabony defects treated with open flap debridement, β-tricalcium phosphate (β-TCP), and carbonate apatite (CO₃Ap) in dogs.

Methods

The mandibular third premolars of four beagle dogs were extracted. Twelve weeks after the extraction, a one-wall bone defect of 4 mm × 5 mm (mesio-distal width × depth) was created on the distal side of the mandibular second premolar and mesial side of the fourth premolar. Each defect was randomly allocated to open flap debridement (control group), periodontal regeneration utilizing β-TCP, or CO₃Ap. Eight weeks after the surgery, histologic and histometric analyses were performed.

Results

No ankylosis, infection, or acute inflammation was observed at any of the experimental sites. Newly formed bone and cementum were observed in all experimental groups. The mineral apposition rate of the alveolar bone crest was higher in the CO₃Ap group than in the control and β-TCP groups. The ratio of the new bone area was significantly higher in the CO₃Ap group than in the control group (P < 0.05). The bone contact percentage of the residual granules was significantly higher in the CO₃Ap group than in the β-TCP group (P < 0.05).

Conclusion

Although this study has limitations, the findings revealed the safety and efficacy of CO₃Ap for periodontal regeneration in one-wall intrabony defects in dogs, and CO₃Ap has a better ability to integrate with bone than β-TCP.

Periodontal Tissue Regeneration by Transplantation of Autologous Adipose Tissue-Derived Multi-Lineage Progenitor Cells With Carbonate Apatite

We have developed an autologous transplantation method using adipose tissue-derived multi-lineage progenitor cells (ADMPCs) as a method of periodontal tissue regeneration that can be adapted to severe periodontal disease. Our previous clinical study confirmed the safety of autologous transplantation of ADMPCs and demonstrated its usefulness in the treatment of severe periodontal disease. However, in the same clinical study, we found that the fibrin gel used as the scaffold material might have caused gingival recession and impaired tissue regeneration in some patients. Carbonate apatite has a high space-making capacity and has been approved in Japan for periodontal tissue regeneration. In this study, we selected carbonate apatite as a candidate scaffold material for ADMPCs and conducted an in vitro examination of its effect on the cellular function of ADMPCs. We further performed autologous ADMPC transplantation with carbonate apatite as the scaffold material in a model of one-wall bone defects in beagles and then analyzed the effect on periodontal tissue regeneration. The findings showed that carbonate apatite did not affect the cell morphology of ADMPCs and that it promoted proliferation. Moreover, no effect on secretor factor transcription was found. The results of the in vivo analysis confirmed the space-making capacity of carbonate apatite, and the acquisition of significant new attachment was observed in the group involving ADMPC transplantation with carbonate apatite compared with the group involving carbonate apatite application alone. Our results demonstrate the usefulness of carbonate apatite as a scaffold material for ADMPC transplantation.

Surgical Periodontal Therapy Using Recombinant Human Fibroblast Growth Factor-2 in Combination with Carbonate Apatite Granules for Stage III Grade B Periodontitis: A Case Report with 1-year Follow-up

This report describes a case of generalized chronic periodontitis requiring periodontal treatment including regenerative therapy. The patient was a 60-year-old woman who visited the Tokyo Dental College Suidobashi Hospital with the chief complaint of tooth mobility and pain in tooth #26. Periodontal examination at the first visit revealed that 32.0% of sites had a probing depth of ≥4 mm and 43.8% bleeding on probing. Radiographic examination revealed vertical bone resorption in #17. Horizontal resorption was noted in other areas. Initial periodontal therapy consisting of plaque control, scaling and root planing, and caries treatment was performed based on a clinical diagnosis of Stage III Grade B periodontitis. Tooth #26 was extracted due to bone resorption extending as far as the root apex. After reevaluation, periodontal regenerative therapy using recombinant human fibroblast growth factor-2 (rhFGF-2) in combination with carbonate apatite (CO₃Ap) granules was performed for #17. Following reevaluation, a zirconia crown (#16) and zirconia bridge (#24-27) were placed. Following further reevaluation, the patient was placed on supportive periodontal therapy (SPT). The periodontal regenerative therapy using rhFGF-2 with CO₃Ap granules yielded an improvement in the vertical bone resorption observed in #17. This improvement has been adequately maintained over a 1-year period postoperatively. Continued SPT is needed to maintain stable periodontal conditions.

Development and characterization of ion-releasing fiber-reinforced flowable composite

OBJECTIVE

This study aimed to develop and characterize an ion-releasing experimental fiber-reinforced flowable composite (Bio-SFRC) and dentin treatment solution made of poly(acrylic acid) (PAA) with a high molecular weight. In addition we also evaluated the interface structure and mineralization potential between the Bio-SFRC and dentin.

METHODS

Some mechanical properties (flexural properties and fracture toughness) of Bio-SFRC in comparison with commercial inert (G-aenial Flo X) and ion-releasing materials (ACTIVA-BioActive Base/Liner and Fuji II LC) were assessed (n = 8/group). Calcium-release at different time-points was measured during the first six weeks by using a calcium-ion selective electrode. Surface analysis of composites after being stored in simulated body fluid (SBF) was investigated by using SEM/EDS. Dentin disks (n = 50) were prepared from extracted sound teeth and demineralization was simulated by acid etching. SEM/EDS was used to evaluate the microstructure of dentin on the top surface and at interface with composites after being stored in SBF.

RESULTS

Bio-SFRC showed higher fracture toughness (1.6 MPa m^1/2) (p < 0.05) compared to Flo X (1.2 MPa m^1/2), ACTIVA (1 MPa m^1/2) and Fuji II LC (0.8 MPa m^1/2). Accumulative calcium release after six weeks from Bio-SFRC (15 mg/l) was higher than other tested ion-releasing materials (≈ 6 mg/l). Mineralization was clearly seen at the interface between treated dentin and Bio-SFRC. None of the commercial tested materials showed signs of mineralization at the interface and dentinal tubules remained open.

SIGNIFICANCE

Developing such reinforced ion-releasing flowable composite and PAA solution might offer the potential for mineralization at the interface and inside the organic matrix of demineralized dentin.

Correction of large jawbone defect in the mouse using immature osteoblast-like cells and a 3D polylactic acid scaffold

Bone tissue engineering has been developed using a combination of mesenchymal stem cells (MSCs) and calcium phosphate-based scaffolds. However, these complexes cannot regenerate large jawbone defects. To overcome this limitation of MSCs and ceramic scaffolds, a novel bone regeneration technology must be developed using cells possessing high bone forming ability and a scaffold that provides space for vertical bone augmentation. To approach this problem in our study, we developed alveolar bone-derived immature osteoblast-like cells (HAOBs), which have the bone regenerative capacity to correct a large bone defect when used as a grafting material in combination with polylactic acid fibers that organize the 3D structure and increase the strength of the scaffold material (3DPL). HAOB-3DPL constructs could not regenerate bone via xenogeneic transplantation in a micromini pig alveolar bone defect model. However, the autogenic transplantation of mouse calvaria-derived immature osteoblast-like cells (MCOBs) isolated using the identical protocol for HAOBs and mixed with 3DPL scaffolds successfully regenerated the bone in a large jawbone defect mouse model, compared to the 3DPL scaffold alone. Nanoindentation analysis indicated that the regenerated bone had a similar micromechanical strength to native bone. In addition, this MCOB-3DPL regenerated bone possesses osseointegration ability wherein a direct structural connection is established with the titanium implant surface. Hence, a complex formed between a 3DPL scaffold and immature osteoblast-like cells such as MCOBs represents a novel bone tissue engineering approach that enables the formation of vertical bone with the micromechanical properties required to treat large bone defects.

Comparison of periodontal wound healing/regeneration by recombinant human fibroblast growth factor-2 combined with β-tricalcium phosphate, carbonate apatite, or deproteinized bovine bone mineral in a canine one-wall intra-bony defect model

AIM

To evaluate periodontal wound healing/regeneration of one-wall intra-bony defects treated with recombinant human fibroblast growth factor-2 (rhFGF-2) and beta-tricalcium phosphate (β-TCP), carbonate apatite (CO₃ Ap), or deproteinized bovine bone mineral (DBBM) in dogs.

MATERIALS AND METHODS

The stability of rhFGF-2 adsorbed onto the bone substitutes was evaluated by Enzyme-Linked Immunosorbent Assay (ELISA). One-wall intra-bony defects (5 × 5 × 5 mm) created in five adult male beagle dogs were treated with rhFGF-2 alone (rhFGF-2), rhFGF-2 with β-TCP (rhFGF-2/β-TCP), rhFGF-2 with CO₃ Ap (rhFGF-2/CO₃ Ap), or rhFGF-2 with DBBM (rhFGF-2/DBBM). Histological outcomes (e.g., linear length of new cementum adjacent to the newly formed bone with inserting collagen fibres [NA] as the primary outcome) were evaluated at 10 weeks post surgery.

RESULTS

Significantly higher amount of rhFGF-2 was adsorbed onto CO₃ Ap compared with β-TCP. Among the treatment groups, the rhFGF-2/DBBM group showed the highest amount of periodontal tissue regeneration. The rhFGF-2/DBBM group showed significantly greater formation of NA (3.22 ± 0.40 mm) compared with rhFGF-2 (1.17 ± 1.00 mm, p < .01) group. Additionally, new bone area in the rhFGF-2/DBBM group (9.78 ± 2.30 mm² ) was significantly higher than that in the rhFGF-2 (5.08 ± 1.26 mm² , p < .01), rhFGF-2/β-TCP (5.91 ± 1.27 mm² , p < .05), and rhFGF-2/CO₃ Ap (6.51 ± 1.49 mm² , p < .05) groups. Slight ankylosis was found in the rhFGF-2/β-TCP (1/9 sites), rhFGF-2/CO₃ Ap (3/10 sites), and rhFGF-2/DBBM (1/9 sites) groups.

CONCLUSIONS

Within their limitations, the present data indicate that DBBM seems to be a suitable carrier for rhFGF-2 and that rhFGF-2/DBBM treatment promotes favourable periodontal regeneration compared with rhFGF-2, rhFGF-2/β-TCP, and rhFGF-2/CO₃ Ap treatments in one-wall intra-bony defects.

Fabrication and histological evaluation of porous carbonate apatite blocks using disodium hydrogen phosphate crystals as a porogen and phosphatization accelerator

The porous architecture of artificial bones plays a pivotal role in bone ingrowth. Although salt leaching methods produce predictable porous architectures, their application in the low-temperature fabrication of ceramics remains a challenge. Carbonate apatite (CO₃ Ap) blocks with three ranges of pore sizes: 100-200, 200-400, and 400-600 μm, were fabricated from CaCO₃ blocks with embedded Na₂ HPO₄ crystals as a porogen and accelerator for CaCO₃ -to-CO₃ Ap conversion. CaCO₃ blocks were obtained from Ca(OH)₂ compacts with Na₂ HPO₄ by CO₂ flow at 100% humidity. When carbonated under 100% water humidity, the dissolution of Na₂ HPO₄ and the formation of hydroxyapatite were observed. Using 90% methanol and 10% water were beneficial in avoiding the Na₂ HPO₄ consumption and generating the metastable CaCO₃ vaterite, which was rapidly converted into CO₃ Ap in a Na₂ HPO₄ solution in 7 days. For the histological evaluation, the CO₃ Ap blocks were implanted in rabbit femur defects. Four weeks after implantation, new bone was formed at the edges of the blocks. After 12 weeks, new bone was observed in the central areas of the material. Notably, CO₃ Ap blocks with pore sizes of 100-200 μm were the most effective, exhibiting approximately 23% new bone area. This study sheds new light on the fabrication of tailored porous blocks and provides a useful guide for designing artificial bones.

Effects of Pore Interconnectivity on Bone Regeneration in Carbonate Apatite Blocks

Porous architecture in bone substitutes, notably the interconnectivity of pores, is a critical factor for bone ingrowth. However, controlling the pore interconnectivity while maintaining the microarchitecture has not yet been achieved using conventional methods, such as sintering. Herein, we fabricated a porous block using the crystal growth of calcium sulfate dihydrate, and controlled the pore interconnectivity by limiting the region of crystal growth. The calcium sulfate dihydrate blocks were transformed to bone apatite, carbonate apatite (CO₃Ap) through dissolution–precipitation reactions. Thus, CO₃Ap blocks with 15% and 30% interconnected pore volumes were obtained while maintaining the microarchitecture: they were designated as CO₃Ap-15 and CO₃Ap-30, respectively. At 4 weeks after implantation in a rabbit femur defect, new bone formed throughout CO₃Ap-30, whereas little bone was formed in the center region of CO₃Ap-15. At 12 weeks after implantation, a large portion of CO₃Ap-30 was replaced with new bone and the boundary with the host bone became blurred. In contrast, CO₃Ap-15 remained in the defect and the boundary with the host bone was still clear. Thus, the interconnected pores promote bone ingrowth, followed by replacement of the material with new bone. These findings provide a useful guide for designing bone substitutes for rapid bone regeneration.

Efficacy of bone grafting materials in preserving the alveolar ridge in a canine model

Preservation of the alveolar ridge after tooth extraction is an essential component for ideal implant positioning. Furthermore, preservation of bone around the implant after implant placement is an essential component for implant treatment. We aimed to evaluate the efficacy of bone grafting materials in preserving the alveolar ridge after implant placement. Implants were placed in regenerated bone without grafting material or with beta-tricalcium phosphate, bovine bone substitute, or carbonate apatite transplantation. In all groups, the bone healed and the implants were successfully placed within the bone. No significant differences in insertion torque and implant stability quotient values were found. The amount of bone around the implant 5 weeks after implant placement was significantly reduced in the bovine bone substitute group; however, implants placed in regenerated bone achieved sufficient initial fixation and osseointegration.

Influence of pH and ion components in the liquid phase on the setting reaction of carbonate apatite granules

Carbonate apatite (CO₃Ap) is an inorganic component of bone and replaces by natural bone after implantation into the bone defect. Because of this unique characteristic, CO₃Ap granules have been used in the dental field. However, washing out of granules from the bone defect area is an issue. The aim of this study was to set CO₃Ap granules by mixing CO₃Ap granules with acidic phosphate solutions and evaluate the influence of the pH and ion components of the solutions. When Na⁺ was the counter ion, the amount of precipitated dicalcium phosphate dihydrate (DCPD) was small and the setting ability disappeared with increasing pH of the solutions. Alternatively, when the counter ion was Ca²⁺, the amount of precipitated DCPD was high and the setting ability was observed even at high pH. These results suggest the presence of Ca²⁺ in the acidic phosphate solution is a key for fabricating CO₃Ap granular cement.

Histomorphometric Evaluation of Bone-Guided Regeneration in Maxillary Sinus Floor Augmentation Using Nano-Hydroxyapatite/Beta-Tricalcium Phosphate Composite Biomaterial: A Case Report

Background

The development of techniques in biomaterials design and production added to advanced surgical procedures which enabled better and more predictable clinical outcomes. Maxillary sinus floor augmentation (MSFA) is among the more studied bone-guided regeneration procedure in the literature. The MSFA could be considered the gold standard procedure for bone-guided regeneration as it provides suitable functional and aesthetic solutions to alveolar ridge atrophy due to tooth loss.

Purpose

This study aimed to conduct a detailed histomorphometric evaluation of collagen production in SFAs bone-guided regeneration, using nano-hydroxyapatite/ß-tricalcium phosphate (nano-HA/ß-TCP) composite.

Patients and Methods

A 52-year-old female had the left upper second premolar condemned due to periodontal disease, then a tooth implant replacement was planned. Due to maxillary sinus pneumatization, the MSFA had to be done before implant placement. Nano-HA/ß-TCP composite (2g) was used in the MSFA procedure. After nine months of the healing process, during the Cone Morse implant installation process, bone samples were collected for histologic analysis (sirius red, hematoxylin/eosin, polarized microscopy). Six months after implant installation, a ceramic crown was installed according to the patient’s request.

Results

Proper masticatory function and aesthetics were re-established. The histomorphometric evaluation indicated that nano-HA/ß-TCP composite did not show any area devoid of cellular activity in sirius red or hematoxylin/eosin staining and the percentage (%) of new bone collagen fibers was achieved using polarization technique evaluation.

Conclusion

According to these results, nano-HA/ß-TCP composite presented clinical and histomorphometric properties suit to be used as bone-guided regeneration biomaterial in MSFA. Furthermore, nano-HA/β-TCP composite provided a favorable nano-environment to bone cells, enhancing bone matrix production.

Replacement Process of Carbonate Apatite by Alveolar Bone in a Rat Extraction Socket

The objective of this study was to investigate a bone graft substitute containing carbonate apatite (CO₃Ap) to analyze bone replacement and the state of bone formation in vitro and in vivo compared with autogenous bone (AB) or control. An osteoclast precursor cell line was cultured with AB or CO₃Ap, and morphological analysis using scanning electron microscopy and a tartrate-resistant acid phosphatase activity assay were performed. The right maxillary first and second molars of Wistar rats were extracted and compensated by AB or CO₃Ap granules. Following implantation, the bone formation state was evaluated after 3, 5, 7, 14, and 28 days of surgery by micro-computed tomography and immunohistostaining. The osteoclast-like cell morphology was typical with many cell protrusions in the AB and CO₃Ap groups. Additionally, the number of osteoclast-like cells formed in the culture increased in each group; however, there was no significant difference between the AB and CO₃Ap groups. Five days after tooth extraction, osteoclasts were observed near CO₃Ap. The bone thickness in the CO₃Ap group was significantly increased than that in the control group and the bone formation in the CO₃Ap group increased by the same level as that in the AB group. CO₃Ap is gradually absorbed by osteoclasts in the extraction socket and is easily replaced by alveolar bone. The process of bone replacement by osteoclasts is similar to that of autologous bone. By observing the process of bone replacement in more detail, it may be possible to gain a better understanding of the bone formation and control the amount of bone after surgery.

Pourbaix-Guided Mineralization and Site-Selective Photoluminescence Properties of Rare Earth Substituted B-Type Carbonated Hydroxyapatite Nanocrystals

Rare-earth labeling in biological apatite could provide critical information for the pathologic transition (osteoclastic) and physiologic regeneration (osteogenesis) of bone and teeth because of their characteristic site-sensitive fluorescence in different coordinative conditions of various tissues in many biological processes. However, the rare-earth labeling method for biological apatites, i.e., carbonated-hydroxyapatite, has been rarely found in the literature. In this paper, we report a Pourbaix-diagram guided mineralizing strategy to controllable carbonation and doping of rare-earth ions in the hydroxyapatite (HA) lattice. The carbonation process of hydroxyapatite was achieved by controllable mineralization in hydrothermal condition with K₂CO₃ as the carbonate source, which results into the pure B-type carbonated hydroxyapatite (CHA) with tunable carbonate substitution degree. All of the as-synthesized materials crystalized into P63/m (No. 176) space group with the lattice parameter of a decreases and c increases with the increasing of carbonate content in the reactants. Structural refinement results revealed that the substitution of planar CO₃²⁻ is superimposed on one of the faces of PO₄³⁻ tetrahedral sub-units with a rotation angle of 30° in reference to c-axis. All of the hydrothermally synthesized CHA nanocrystals show hexagonal rod-like morphology with the length of 70–110 nm and diameter of 21–35 nm, and the decreasing length/diameter ratio from 3.61 to 2.96 from low to high carbonated level of the samples. Five rare-earth cations, of Pr³⁺, Sm³⁺, Eu³⁺, Tb³⁺, and Ho³⁺, were used as possible probe ions that can be doped into either HA or CHA lattice. The site-preference of Tb³⁺ doping is the same in the crystallographic site of HA and CHA according to characteristic emission peaks of ⁵D₄–⁷F_j (j = 3–6) transitions in their photoluminescent spectroscopy. Our work provides a controllable carbonation method for rare-earth labeling hydroxyapatite nanomaterials with potential biologically active implant powders for bone repair and tissue regeneration.

Fabrication and Histological Evaluation of a Fully Interconnected Porous CO3Ap Block Formed by Hydrate Expansion of CaO Granules

Carbonate apatite (CO₃Ap) fabricated by a dissolution-precipitation reaction from a precursor exhibits excellent osteoconductivity and is readily replaced by bone. In the present study, a fully interconnected porous CO₃Ap block was fabricated by hydrate expansion and carbonation of CaO granules, and the resulting CaCO₃ was then converted to CO₃Ap. When CaO granules were exposed to 100% humidity CO₂ in a closed vessel, the CaO granules were hydrated and expanded to form a porous Ca(OH)₂ block. The block was then carbonated to form a porous CaCO₃ block, which was then immersed in a Na₂HPO₄ solution to convert it to a porous CO₃Ap block. The resulting CO₃Ap block possessed a fully interconnected porous structure. Histological analyses 4 and 8 weeks after implantation in rabbits revealed that the porous CO₃Ap block resulted in more significant material resorption and bone formation than the dense CO₃Ap block. Therefore, it was concluded that a fully interconnected porous CO₃Ap block fabricated by the hydrate expansion of CaO granules has potential value as a bone substitute.