Influence of Cyclic Loading on Fiber Post and Composite Resin Core

Influence of one-wall remaining coronal tooth with resin abutment and fiber post on static and dynamic fracture resistance

The objective of this study was to determine the influence of height and thickness of the one wall remaining coronal tooth structure on the fracture resistance of an endodontically treated root with resin abutment build-up using resin composite and fiber-reinforced resin composite post. Static and dynamic fracture tests were performed by placing the remaining tooth wall on the tensile side and applying loads at an angle of 30° from the tooth axis. Superior static fracture resistance was observed when the wall remaining on the tooth had a height and thickness greater than 1.0 mm. The dynamic fatigue test showed high loading capacity or fracture resistance in specimens with large height and thickness. The dynamic fatigue test showed the influence of the remaining tooth structure on fracture resistance clearly. In conclusion, the static and dynamic fracture resistances increased with the height and thickness of the one wall remaining tooth structure.

Impact of Endodontic Kinematics on Stress Distribution During Root Canal Treatment: Analysis of Photoelastic Stress

INTRODUCTION

Structural defects created by endodontic treatment are the most common cause of major dental failures. This study analyzed levels of stress produced by endodontic instruments during the root canal treatment by photoelastic analysis of stress.

METHODS

Twenty-four human premolars were randomly divided into 4 groups (n = 6) according to instrumentation protocol: ProTaper Next (GPT), One Shape (GOS), Wave One Gold (GWO), and TF Adaptive (GTF). The evaluation of the photoelastic model was performed at 4 dental zones: dental-crown region, cervical third of root, middle third of root, and apical third of root. Silicone molds were prepared (2 × 15 mm), and pinjets were used inside the root canals to fixate teeth. Photoelastic resin (2:1 ratio) was poured into the silicone molds to form photoelastic models. A transmission polariscope was used to analyze the positions of interest and recorded with a digital camera. Tardy's method was used to quantify the fringe order (n) and calculate the maximum stress value (τ) at each selected point. Data were analyzed with two-way analysis of variance, Tukey test (P < .05), fringe descriptive analysis.

RESULTS

All groups showed a significant increase in the level of stress created during biomechanical preparation of the root canals. In the quantitative analysis, there was no statistically significant difference among the groups (P > .05). In the qualitative analysis, GPT and GTF instruments achieved greater levels of stresses compared with GWO and GOS instruments. At the beginning of instrumentation, stresses were concentrated at the coronary level and the end of instrumentation at the middle and apical root level.

CONCLUSIONS

All endodontic systems resulted in accumulation of stress along the dental structure. Stress was found in different concentrations along the tooth and at different levels.

Influence of post material, post diameter, and substance loss on the fracture resistance of endodontically treated teeth: A laboratory study

STATEMENT OF PROBLEM

The influence of the flexural modulus of prefabricated posts on the fracture resistance of endodontically treated teeth is unclear.

PURPOSE

The purpose of this in vitro study was to evaluate the influence of post material and post diameter on the fracture resistance of endodontically treated mandibular premolars. In addition, the influence of tooth substance loss was evaluated by comparing 1 with 2 residual dentinal walls.

MATERIAL AND METHODS

Sixty-four extracted mandibular first premolars were endodontically treated and divided into 8 test groups (n=8) based on the number of residual walls (1 or 2), post material (glass fiber or titanium) and post diameter (International Standards Organization [ISO] 70 or ISO 90). After luting the posts, the specimens received a composite resin core and a crown preparation with a 2-mm ferrule. Cast Co-Cr crowns were cemented with glass ionomer cement. After 1 200 000 mastication cycles with a load of 49 N and simultaneous thermocycling (5 °C-55 °C), specimens were quasistatically loaded at 30 degrees to the longitudinal axis of the tooth until fracture. Fracture loads were analyzed by using 3-way ANOVA (α=.05). Fracture modes were examined with a stereomicroscope at ×25 magnification and recorded.

RESULTS

Fracture loads ranged from 954 ±35 N (1 residual wall-glass fiber-ISO 70) to 1286 ±202 N (1 residual wall-glass fiber-ISO 90). Titanium posts showed a statistically significant higher fracture resistance than glass fiber posts. A statistically significant increase in fracture resistance was also observed with increasing post diameter. However, no significant difference was found with respect to the number of residual walls (P>.05).

CONCLUSIONS

Teeth restored with titanium posts exhibited higher fracture resistance than teeth restored with glass fiber posts, especially when smaller diameter posts were used.

Influence of periodontal ligament simulation on bond strength and fracture resistance of roots restored with fiber posts

Objective

Considering that periodontal ligament simulation may influence the stress distribution over teeth restored with intraradicular retainers, this study aimed to assess the combined effect of mechanical cycling and periodontal ligament simulation on both the bond strength between fiber posts and root dentin and the fracture resistance of teeth restored using glass fiber posts.

Material and Methods

Ninety roots were randomly distributed into 3 groups (n=10) (C-MC: control; P-MC: polyether; AS-MC: addition silicone) to test bond strength and 6 groups (n=10) (C: control; P: polyether; AS: addition silicone, without mechanical cycling, and C-MC, P-MC and AS-MC with mechanical cycling) to test fracture strength, according to the material used to simulate the periodontal ligament. For the bond strength test, fiber posts were cemented, cores were built, mechanical cycling was applied (2×106 cycles, 88 N, 2.2 Hz, and 45º incline), and the teeth cut into 3 slices (2 mm), which were then subjected to the push-out test at 1 mm/min. For the fracture strength test, fiber posts were cemented, cores were built, and half of the groups received mechanical cycling, followed by the compressive strength (45° to the long axis and 1 mm/min) performed on all groups.

Results

Periodontal ligament simulation did not affect the bond strength (p=0.244) between post and dentin. Simulation of periodontal ligament (p=0.153) and application of mechanical cycling (p=0.97) did not affect fracture resistance.

Conclusions

The materials used to simulate the periodontal ligament did not affect fracture or bond strength, therefore periodontal ligament simulation using the tested materials could be considered optional in the conditions of the study.

Grinding efficiency of abutment tooth with both dentin and core composite resin on axial plane

The purpose of this study was to evaluate grinding efficiency in abutment teeth comprising both dentin and core composite resin in the axial plane. Grinding was performed over 5 runs at two loads (0.5 or 0.25 N) and two feed rates (1 or 2 mm/sec). The grinding surface was observed with a 3-D laser microscope. Tomographic images of the grinding surfaces captured perpendicular to the feed direction were also analyzed. Using a non-ground surface as a reference, areas comprising only dentin, both dentin and core composite resin, or only core composite resin were analyzed to determine the angle of the grinding surface. Composite resins were subjected to the Vickers hardness test and scanning electron microscopy. Data were statistically analyzed using a one-way analysis of variance and multiple comparison tests. Multiple regression analysis was performed for load, feed rate, and Vickers hardness of the build-up material depending on number of runs. When grinding was performed at a constant load and feed rate, a greater grinding angle was observed in areas comprising both dentin and composite resin or only composite resin than in areas consisting of dentin alone. A correlation was found between machinability and load or feed rate in areas comprising both dentin and composite resin or composite resin alone, with a particularly high correlation being observed between machinability and load. These results suggest that great caution should be exercised in a clinical setting when the boundary between the dentin and composite resin is to be ground, as the angle of the grinding surface changes when the rotating diamond point begins grinding the composite resin.

Effect of root canal preparation, type of endodontic post and mechanical cycling on root fracture strength

Objective

To evaluate the impact of the type of root canal preparation, intraradicular post and mechanical cycling on the fracture strength of roots.

Material and Methods

eighty human single rooted teeth were divided into 8 groups according to the instruments used for root canal preparation (manual or rotary instruments), the type of intraradicular post (fiber posts- FRC and cast post and core- CPC) and the use of mechanical cycling (MC) as follows: Manual and FRC; Manual, FRC and MC; Manual and CPC; Manual, CPC and MC; Rotary and FRC; Rotary, FRC and MC; Rotary and CPC; Rotary, CPC and MC. The filling was performed by lateral compactation. All root canals were prepared for a post with a 10 mm length, using the custom #2 bur of the glass fiber post system. For mechanical cycling, the protocol was applied as follows: an angle of incidence of 45°, 37°C, 88 N, 4 Hz, 2 million pulses. All groups were submitted to fracture strength test in a 45° device with 1 mm/ min cross-head speed until failure occurred.

Results

The 3-way ANOVA showed that the root canal preparation strategy (p<0.03) and post type (p<0.0001) affected the fracture strength results, while mechanical cycling (p=0.29) did not.

Conclusion

The root canal preparation strategy only influenced the root fracture strength when restoring with a fiber post and mechanical cycling, so it does not seem to be an important factor in this scenario.

Loading Standardization of Postendodontic Restorations In Vitro: Impact of Restorative Stage, Static Loading, and Dynamic Loading

Objective

The load capability of post-restored endodontically treated teeth (ETT) can be determined at different restorative stages. It was the aim of this study to compare the load capability of ETT at these stages.

Materials and Methods

Maxillary central incisors were divided into 4 groups (n=10) and endodontically treated. Specimens were restored with: (I) only glass fiber posts (GFP); (II) GFP and composite build-up with 2 mm ferrule; (III and IV) with additional adhesively luted all-ceramic crowns. Group (I) to (III) were statically loaded, and group (IV) was exposed to thermomechanical loading (TML) and subsequent static loading.

Results

The lowest median load level of 73 N was determined for group (I). The maximum median load value of 331 N was found for group (III). The comparison of Fmax [N] of group (I), (II) and (III) revealed significant differences between the groups (p&lt;0.001). The specimens of group (IV) failed at significantly lower load values (p&lt;0.005) as similarly restored specimens of group (III) which were only statically loaded. The stage of restoration and TML loading prior to static loading had a significant impact on fracture patterns (p=0.006).

Conclusion

Every additional restorative step torwards a final crown-restored ETT significantly increased the load capability. TML prior to load-to-fracture testing of the complete restorative complex, ie. post, core and crown, significantly decreased maximum load capability.

Photoelastic stress analysis of endodontically treated teeth restored with different post systems: normal and alveolar bone resorption cases

The present study examined the influence of different post materials and their lengths on the mechanical stress of endodontically treated incisor roots in two alveolar bone conditions. Two-dimensional photoelastic models were fabricated to simulate the endodontically treated maxillary central incisors restored with three kinds of posts materials (low Young's modulus glass fiber post, high Young's modulus glass fiber post, and prefabricated stainless steel post) and two post lengths (8 and 4 mm). Completed models were placed in a transmission polariscope and loaded with a static force of 150 N at 45° to the tooth axis. Photoelastic photographs and the magnitudes of fringe order revealed stress distribution in the root, and suggest that the glass fiber post with a low Young's modulus and long length can reduce the stress concentration both in normal and alveolar bone resorption conditions.

AFM characterization of bovine enamel and dentine after acid-etching

Teeth are constituted mainly of hydroxyapatite molecules (Ca(10)(PO(4))(6)(OH)(2)), grouped in different microstructural arrangements, depending on the dental layer considered (enamel or dentine). In the present work, these dental microstructural arrangements were characterized by atomic force microscopy. Enamel and dentine samples were cut from freshly extracted bovine incisor teeth. After metallographic polishing, the dental surfaces were etched with lactic acid (113.8 mmol/L, pH 3.3). Three etching times were tested: 1, 3 and 5 min. Atomic force micrographs showed that 1 min of etching time was effective to remove the smear layer, polishing debris and scratches, and display the characteristics of interest for both enamel and dentine. Although the bovine dental enamel rod cross-section presented keyhole-like shape, its measured dimensions (8.8 microm of major axis and 3.7 microm of minor axis) exhibited an insignificant discrepancy from human prisms diameters. Bovine dentinal tubules displayed larger mean diameters (4.0 microm) and a lower density (approximately 17,100 tubules/mm(2)) than human dentine, suggesting that the use of bovine dentine as a substitute for human dentine in resin adhesion investigations should be reconsidered. Apatite nanoparticles presented a mean radius (22-23 nm) considerably smaller than that of human teeth.