A Comparison of Friction Measurements of Intact Articular Cartilage in Contact with Cartilage, Glass, and Metal

Comparison of wear on articular cartilage by titanium alloy, ultra-high-molecular-weight polyethylene, and carbon fibre reinforced polyether-ether-ketone: A pilot study

Artificial implant materials may articulate against native articular cartilage in certain clinical scenarios and the selection of an implant material that results in the least wear on articular cartilage is preferred to maintain normal joint architecture and function. This project compared the wear on porcine femoral condyles induced by articulation against porcine patellae, titanium alloy (Ti6Al4V), ultra high molecular weight polyethylene (UHMWPE), and carbon fibre reinforced polyether-ether-ketone (CFR-PEEK) through an ex vivo experimental setup. A sinusoidal compressive load of 30-160 N, representing an approximate joint pressure of 0.19-1 MPa at a frequency of 3 Hz coupled with a rotational displacement of +/- 10⁰ at 3 Hz was used to simulate physiological joint motion. Wear was characterized via gross examination and histologically using the OARSI scoring system after 43,200 cycles. CFR-PEEK resulted in the most significant wear on articular cartilage compared to titanium alloy and UHMWPE whereas titanium alloy and UHMWPE resulted in similar levels of wear. All materials caused more wear compared to cartilage-on-cartilage testing. The wear mechanism was characterized by progressive loss of proteoglycan content in cartilage in histology samples.

Effect of coronal fracture angle on the stability of screw fixation in medial malleolar fractures: A finite element analysis

Malleolar screw fixation is the most widely used treatment method for medial malleolar (MM) fractures. Here, although buttress plate fixation is advocated for vertical MM fractures, the angular discrimination between oblique and vertical MM fractures is still not fully understood. The purpose of this study is to test the adequacy of screw fixation in MM fractures with different angles and determination of a ‘critical fracture angle’ to guide surgeons in the decision-making for screw fixation for MM fractures by utilizing an advanced engineering simulation approach. In addition to loading of the healthy tibia structure, various cases of the MM fracture double screw fixation (14 simulation scenarios in total with fracture angles between 30° and 90°, in 5° increments) were considered in this research and their static loading conditions just after fixation operation were simulated through nonlinear (geometric and contact nonlinearity) finite element analysis (FEA). Patient-specific computed tomography scan data, parametric three-dimensional solid modelling and finite element method (FEM) based engineering codes were employed in order to simulate the fixation scenarios. Visual and numerical outputs for the deformation and stress distributions, separation and sliding behaviours of the MM fracture fragments of various screw fixations were clearly exhibited through FEA results. Minimum and maximum separation distances (gap) of 3.75 and 150.34 µm between fracture fragments at fracture angles of 30° and 90° were calculated respectively against minimum and maximum sliding distances of 25.87 and 41.37 µm between fracture fragments at fracture angles of 90° and 35°, respectively. The FEA results revealed that while the separation distance was increasing, the sliding distance was decreasing and there were no distinct differences in sliding distances in the scenarios from fracture angles of 30°–90°. The limitations and errors in a FEA study are inevitable, however, it was interpreted that the FEA scenarios were setup in this study by utilizing acceptable assumptions providing logical outputs under pre-defined boundary conditions. Finally, the fracture healing threshold for separation and/or sliding distance between fracture fragments was assigned as 100 µm by referring to previous literature and it was concluded that the screws fixed perpendicular to the fracture in a MM fracture with more than 70° angle with the tibial plafond results in a significant articular separation (>100 µm) during single-leg stand. Below this critical angle of 70°, two screws provide sufficient fixation.

The effect of talus osteochondral defects of different area size on ankle joint stability: a finite element analysis

BACKGROUND

Osteochondral lesion of the talus (OLT) is one of the most common ankle injuries, which will lead to biomechanical changes in the ankle joint and ultimately affect ankle function. Finite element analysis (FEA) is used to clarify the effect of talus osteochondral defects on the stability of the ankle joint at different depths. However, no research has been conducted on talus osteochondral defect areas that require prompt intervention. In this research, FEA was used to simulate the effect of the area size of talus osteochondral defect on the stress and stability of the ankle joint under a specific depth defect.

METHODS

Different area sizes (normal, 2 mm* 2 mm, 4 mm* 4 mm, 6 mm* 6 mm, 8 mm* 8 mm, 10 mm* 10 mm, and 12 mm* 12 mm) of the three-dimensional finite element model of osteochondral defects were established. The model was used to simulate and calculate joint stress and displacement of the articular surface of the distal tibia and the proximal talus when the ankle joint was in the heel-strike, midstance, and push-off phases.

RESULTS

When OLT occurred, the contact pressure of the articular surface, the equivalent stress of the proximal talus, the tibial cartilage, and the talus cartilage did not change significantly with an increase in the size of the osteochondral defect area when the heel-strike phase was below 6 mm * 6 mm. Gradual increases started at 6 mm * 6 mm in the midstance and push-off phases. Maximum changes were reached when the defect area size was 12 mm * 12 mm. The same patterns were observed in the talus displacement.

CONCLUSIONS

The effect of the defect area of the ankle talus cartilage on the ankle biomechanics is evident in the midstance and push-off phases. When the size of the defect reaches 6 mm * 6 mm, the most apparent change in the stability of the ankle joint occurs, and the effect does not increase linearly with the increase in the size of the defect.

Comparison of Fixation Techniques in Oblique and Biplanar Chevron Medial Malleolar Osteotomies; a Finite Element Analysis

This study aimed to evaluate different fixation techniques and implants in oblique and biplanar chevron medial malleolar osteotomies using finite element analysis. Both oblique and biplanar chevron osteotomy models were created, and each osteotomy was fixed with 2 different screws (3.5 mm cortical screw and 4.0 mm malleolar screw) in 2 different configurations; (1) 2 perpendicular screws, and (2) an additional third transverse screw. Nine simulation scenarios were set up, including 8 osteotomy fixations and the intact ankle. A bodyweight of 810.44 N vertical loading was applied to simulate a single leg stand on a fixed ankle. Sliding, separation, frictional stress, contact pressures between the fragments were analyzed. Maximum sliding (58.347µm) was seen in oblique osteotomy fixed with 2 malleolar screws, and the minimum sliding (17.272 µm) was seen in chevron osteotomy fixed with 3 cortical screws. The maximum separation was seen in chevron osteotomy fixed with 2 malleolar screws, and the minimum separation was seen in oblique osteotomy fixed with 3 cortical screws. Maximum contact pressure and the frictional stress at the osteotomy plane were obtained in chevron osteotomy fixed with 3 cortical screws. The closest value to normal tibiotalar contact pressures was obtained in chevron osteotomy fixed with 3 cortical screws. This study revealed that cortical screws provided better stability compared to malleolar screws in each tested osteotomy and fixation configuration. The insertion of the third transverse screw decreased both sliding and separation. Biplanar chevron osteotomy fixed with 3 cortical screws was the most stable model.