Experimental Testing of Vibration Analysis Methods to Monitor Recovery of Stiffness of a Fixated Synthetic Pelvis: A Preliminary Study

Different Lengths of Percutaneous Transverse Iliosacral Screw in Geometric Osseous Fixation Pathway: A Finite-Element Analysis

OBJECTIVE

To evaluate the biomechanical performances of the sacroiliac screw fixation of the first sacral vertebra with different lengths of screws using the Finite-Element Method.

METHODS

First, pelvic CT images were generated from a healthy volunteer, and multislice sagittal views were produced to determine the axis for the first sacral vertebra geometric osseous fixation pathway (GOFP). Subsequently, according to the geometric size and mechanical parameters of the iliosacral screw, the screw models with the same diameter of 7.3 mm and different lengths of 80 mm, 90 mm, 100 mm, 110 mm, 120 mm, 130 mm and 140 mm were built. Then the seven screws were assembled with the pelvic model. The maximum von Mises stress and the shape variables were evaluated for the pelvis and the screws.

RESULTS

Results are shown for the pelvic and GOFP screw, respectively. The simulation results show that the maximum von Mises stress in the cortex of the pelvic ring of the pelvis with the 130-mm length screw is the lowest among the pelvic models with different screws. Moreover, the peak displacement of the pelvis with the 130-mm length screw is the smallest. These results indicate that under the standing condition, a 130-mm length screw can decrease the stress concentration and result in a more effective transfer of stress within the reconstructed pelvis. In addition, the displacement of the screw with a 130-mm length is the smallest among all the considered screws. The peak von Mises stresses in the 130-mm length screw and the cortex are still within a low and elastic range below the yielding strengths of the materials.

CONCLUSION

Through the finite element analysis, the GOFP can be used as a safe and effective way for iliosacral screw fixation. The optimal length of the screw may be 130 mm length.

Quantitative assessment of compress-type osseointegrated prosthetic implants in human bone using electromechanical impedance spectroscopic methods

Osseointegrated (OI) prostheses are a promising alternative to traditional socket prostheses. They can enhance the quality of life of amputees by avoiding fit and comfort issues commonly associated with sockets. The main structural element of the OI prosthesis is a biocompatible metallic implant that is surgically implanted into the bone of the residual limb. The implant is designed to provide a conducive surface for the host bone to osseointegrate with. The osseointegration process of the implant is difficult to clinically evaluate, leading to conservative postoperative rehabilitation approaches. Elastic stress waves generated in an OI prosthesis have been previously proposed to interrogate the implant-bone interface for quantitative assessment of the osseointegration process. This paper provides a detailed overview of the various elastic stress wave methods previously explored for in situ characterization of OI implants. Specifically, the paper explores the use of electromechanical impedance spectroscopy (EIS) to assess the OI process in compress-type OI prostheses. The EIS approach measures the electrical impedance spectrum of lead zirconate titanate elements bonded to the free end of the implant. The research utilizes both numerical simulation and experimental verification to establish that the electromechanical impedance spectrum is sensitive (between 400 and 460 kHz) to both the degree and location of osseointegration. A baseline-free OI index is proposed to quantify the degree of osseointegration at the implant-bone interface and to assess the stability of the OI implant for clinical decision making.

Biomechanical study of different fixation techniques for the treatment of sacroiliac joint injuries using finite element analyses and biomechanical tests

The pelvis is one of the most stressed areas of the human musculoskeletal system due to the transfer of truncal loads to the lower extremities. Sacroiliac joint injury may lead to abnormal joint mechanics and an unstable pelvis. Various fixation techniques have been evaluated and discussed. However, it may be difficult to investigate each technique due to variations in bone quality, bone anatomy, fracture pattern, and fixation location. Additionally, the finite element method is one useful technology that avoids these variations. Unfortunately, most previous studies neglected the effects of the lumbar spine and femurs when they investigated the biomechanics of pelvises. Thus, the aim of this study was to investigate the biomechanical performance of intact, injured, and treated pelvises using numerical and experimental approaches. Three-dimensional finite element models of the spine-pelvis-femur complex with and without muscles and ligaments were developed. The intact pelvis, the pelvis with sacroiliac joint injury, and three types of pelvic fixation techniques were analyzed. Concurrently, biomechanical tests were conducted to validate the numerical outcomes using artificial pelvises. Posterior iliosacral screw fixation showed relatively better fixation stability and lower risks of implant failure and pelvic breakage than sacral bar fixation and a locking compression plate fixation. The present study can help surgeons and engineers understand the biomechanics of intact, injured, and treated pelvises. Both the simulation technique and the experimental setup can be applied to investigate different pelvic injuries.

Relationship between the shape and density distribution of the femur and its natural frequencies of vibration

It has been recently suggested that mechanical loads applied at frequencies close to the natural frequencies of bone could enhance bone apposition due to the resonance phenomenon. Other applications of bone modal analysis are also suggested. For the above-mentioned applications, it is important to understand how patient-specific bone shape and density distribution influence the natural frequencies of bones. We used finite element models to study the effects of bone shape and density distribution on the natural frequencies of the femur in free boundary conditions. A statistical shape and appearance model that describes shape and density distribution independently was created, based on a training set of 27 femora. The natural frequencies were then calculated for different shape modes varied around the mean shape while keeping the mean density distribution, for different appearance modes around the mean density distribution while keeping the mean bone shape, and for the 27 training femora. Single shape or appearance modes could cause up to 15% variations in the natural frequencies with certain modes having the greatest impact. For the actual femora, shape and density distribution changed the natural frequencies by up to 38%. First appearance mode that describes the general cortical bone thickness and trabecular bone density had one of the strongest impacts. The first appearance mode could therefore provide a sensitive measure of general bone health and disease progression. Since shape and density could cause large variations in the calculated natural frequencies, patient-specific FE models are needed for accurate estimation of bone natural frequencies.