Stress distributions in peri-miniscrew areas from cylindrical and tapered miniscrews inserted at different angles

Cortical bone microdamage affects primary stability of orthodontic miniscrew

BACKGROUND

The aim of this study was to investigate the effects of orthodontic miniscrew pitch and thread shape on microdamage in cortical bone. The relationship between the microdamage and primary stability was also examined.

METHODS

Ti6Al4V orthodontic miniscrews and 1.0-mm-thick cortical bone pieces from fresh porcine tibia were prepared. The orthodontic miniscrews had custom-made thread height (H) and pitch (P) size geometries, and were classified into three groups: control geometry; HCPC (HC; thread height = 0.12 mm, PC; pitch size = 0.60 mm), geometry with a narrower pitch; HCPN (HC; thread height = 0.12 mm, PN; pitch size = 0.30 mm), and geometry with a taller thread height; HTPC (HT; thread height = 0.36 mm, PC; pitch size = 0.60 mm). The orthodontic miniscrews were inserted into a pilot hole in the cortical bone, and maximum insertion torque and Periotest value were measured. After insertion, the samples were stained with basic fuchsin. Histological thin sections were obtained and the bone microdamage parameters, i.e., total crack length and total damage area, and insertion state parameters, i.e., orthodontic miniscrew surface length and bone compression area were calculated.

RESULTS

The orthodontic miniscrews with the taller thread height resulted in lower primary stability with minimal bone compression and microdamage; however, the narrower thread pitch led to maximum bone compression and extensive bone microdamage.

CONCLUSIONS

A wider thread pitch reduced microdamage, and decreased thread height resulted in increased bone compression, ultimately resulting in increased primary stability.

Temporary anchorage devices and the forces and effects on the dentition and surrounding structures during orthodontic treatment: a scoping review

BACKGROUND

Temporary anchorage devices (TADs) offer the clinician an immediate temporary source of skeletal anchorage for a range of orthodontic interventions. It is important to understand forces involved in using TADs and the effects on the dentition and surrounding structures, to improve clinical outcomes.

OBJECTIVE

To examine and qualitatively synthesize literature on the forces involved with the use of TADs and the effects on the dentition and surrounding structures in orthodontic tooth movement, to provide better understanding of the complex interactions and the clinical implications.

SEARCH METHODS

Electronic databases searched included: Cochrane Library [including Central Register of Controlled Trials (CENTRAL)], Embase via OVID, Pubmed, and Scopus. Study screening and selection were conducted in duplicate.

SELECTION CRITERIA

Studies selected were clinical studies, simulation studies (computer or laboratory-based), or animal studies with no restriction over gender, age, study type (excluding case reports), or setting. Studies focusing on the forces involved with the use of TADs in orthodontic treatment and their effects on the dentition and surrounding structures were included.

DATA COLLECTION AND ANALYSIS

A data charting form was piloted and refined. Data charting was performed independently and in duplicate. This consisted of key fields with predetermined options and free text. The extracted data were collated, and a narrative synthesis conducted.

RESULTS

The results from 203 included studies were grouped into seven TAD based interventions combining the clinical, simulation, and animal studies. They were: En masse retraction of anterior teeth, intrusion, movement of a single tooth, orthopaedic interventions, distalisation, maxillary expansion and other types. The forces involved with the use of TADs, and their effects on the dentition and surrounding structures, were presented in descriptive and tabular formats.

LIMITATIONS

This review restricted study language to English. Formal appraisal of the quality of evidence is not a required feature of scoping reviews, as per the PRISMA-ScR guidelines, however it was evident that a proportion of clinical studies were of high risk of bias and low quality and therefore any proposed changes the reader may consider to their clinical practice should be contextualized in light of this.

CONCLUSIONS

Across the seven types of TAD based interventions the effects on the dentition and surrounding structures are described providing a better understanding of the complex interactions. A guide to the level and direction of forces in each type of intervention is provided to aid clinicians in achieving high quality outcomes.

IMPLICATIONS

There is a need to validate future FEA simulation studies by comparing to clinical data. It is also recommended that future scoping reviews incorporate a formal critical appraisal of studies to facilitate the translation of the results into clinical practice. Development of a standard set of terms for TADs is recommended to facilitate future research.

REGISTRATION

Registration of a scoping review is not possible with PROSPERO.

FUNDING

None to declare.

Effect of Different Surface Designs on the Rotational Resistance and Stability of Orthodontic Miniscrews: A Three-Dimensional Finite Element Study

High orthodontic forces and various directions of applied forces can be associated with loosening of the screw anchorage in the bone. Screw designs have been modified to increase the stability of the miniscrews. This research evaluates the influence of three-designs on the stability of orthodontic miniscrews. A conventionally cylinder-type miniscrew design (Bio-Action screw, Jin-Biomed co., Bucheon, Korea) was set as a control, and three conditions were studied based on modifications of this control design. Condition-1 has narrowed threads in the upper part of the screw; Condition-2 has a notch at the middle part; and Condition-3 has the combination of Condition-1 and Condition-2. The moment required to unwind the miniscrew to five degrees is tested, and the moment generated at the cortical bone and the trabecular bone were calculated with finite element analysis. Compared to the control, all three conditions showed a higher moment required to unwind the miniscrew and a higher moment generated at the cortical bone. At the trabecular bone, condition-2 and -3 showed higher moment than the control, and condition-1 showed similar moment to the control. Condition-3 required a higher overall moment to unwind the miniscrew. These findings validate the design modifications used to increase the rotational resistance.

Distribution and amount of stresses caused by insertion or removal of orthodontic miniscrews into the maxillary bone: A finite element analysis

OBJECTIVE

Initial stability of miniscrews is an important factor in their success as orthodontic anchorages. One of the factors affecting this stability is the stresses exerted to the bone by the screw. Since the distribution and extent of stresses and strains produced during insertion or removal of miniscrews had not been measured before, this study used finite element analysis (FEA) to measure these parameters in tapered versus cylindrical screws with or without pilot sockets.

MATERIALS AND METHODS

An FEA model of maxilla, pilot hole, and tapered/cylindrical miniscrews were created from 875 CT scan data. The bone cortex was considered 2mm thick. The cancellous bone was reconstructed below the cortical bone. Miniscrews were modelled on the basis of commercial titanium tapered and cylindrical miniscrews (1.6mm wide, 8mm long). The diameter and length of the guiding hole were considered to be 1.1 and 1.5mm, respectively. The miniscrews were inserted (and removed) between the maxillary second premolar and first molar. Stress/strain produced in the bones or screws were measured.

RESULTS

During screw insertion, in all setups, the highest stress existed within both the bone and screw, when the screw was in the cortical bone; after insertion into the cancellous bone, the stress suddenly dropped. In cylindrical screws, the highest amount of stress was distributed around the neck which was used for screw driving. In tapered screws, the stress was mostly distributed around the front one-third of the screw. During screw removal, the results of four setups were rather similar with stresses concentrated around screw necks, in the depth of the screw hole, and around the bone surface. The greatest bone stress during insertion was caused by the pilot-less tapered screw (10.18MPa) and the lowest stress was exerted by a pilot-less cylindrical screw (0.74MPa).

CONCLUSION

Most of the stress and strain is tolerated by the cortical bone and not the cancellous one. Using cylindrical miniscrews might be more bone-friendly. However, all cases had stresses below tolerable thresholds, and hence are safe.

Investigation of the optimal design of orthodontic mini-implants based on the primary stability: A finite element analysis

Background. The design of an orthodontic mini-implant is a significant factor in determining its primary stability and its clinical success. The aim of this study was to measure the relative effect of mini-implant design factors on primary stability of orthodontic mini-implants.

Methods. Thirty-two 3-dimensional assemblies of mini-implant models with their surrounding bone were generated using finite element analysis software. The maximum displacement of each mini-implant model was measured as they were loaded with a 2-N horizontal force. Employing Taguchi’s design of experiments as a statistical method, the contribution of each design factor to primary stability was calculated. As a result of the great effect of the upper diameter and length, to better detect the impact of the remaining design factors, another set of 25 models with a fixed amount of length and diameter was generated and evaluated.

Results. The diameter and length showed a great impact on the primary stability in the first set of experiments (P<0.05). According to the second set of experiments, increased taper angle in the threaded and non-threaded area decreased the primary stability. There was also an optimum amount of 2.5 mm for threaded taper length beyond which the primary stability decreased.

Conclusion. It is advisable to increase the diameter and length if primary stability is at risk. In the second place, a minimum amount of taper angle, both in the threaded and non-threaded area with an approximate proportion of 20% of threaded taper length to MI length, would be desirable for MIs with a moderate size.

The effect of fluoride-containing oral rinses on the corrosion resistance of titanium alloy (Ti-6Al-4V)

OBJECTIVE

The purpose of this study was to examine the effect of commercially available fluoride-containing oral rinses on the corrosion behavior of titanium alloys, which are the main components of orthodontic miniscrews.

METHODS

Four commercially available oral rinses (solution A, pH 4.46/260 ppm fluoride; solution B, pH 4.41/178 ppm fluoride; solution C, pH 6.30/117 ppm fluoride; and solution D, pH 4.17/3.92 ppm fluoride) were tested on titanium alloy (Ti-6Al-4V) circular plates, and saline was used as the control. The open-circuit potential and potentiodynamic polarization of these materials were measured. Thereafter, all samples were evaluated under a field-emission scanning electron microscope.

RESULTS

Among the tested oral rinses, except solution D, the more the fluoride content was, the greater was the corrosion potential downtrend; the corrosion resistance of the titanium alloy sample was also lowered significantly (p < 0.05). Field-emission scanning electron microscopic analysis of the surface morphology of the titanium alloy samples revealed that all samples had some defects, crevices, or pitting after exposure to the oral rinses than before treatment. In particular, the samples in solution A showed the most changes.

CONCLUSIONS

Commercially available oral rinses having a high fluoride concentration and a low pH may reduce the corrosion resistance of titanium alloys used in dental appliances such as orthodontic titanium miniscrews and brackets.

Bone cutting capacity and osseointegration of surface-treated orthodontic mini-implants

Objective

The objective of the study was to evaluate the practicality and the validity of different surface treatments of self-drilling orthodontic mini-implants (OMIs) by comparing bone cutting capacity and osseointegration.

Methods

Self-drilling OMIs were surface-treated in three ways: Acid etched (Etched), resorbable blasting media (RBM), partially resorbabla balsting media (Hybrid). We compared the bone cutting capacity by measuring insertion depths into artificial bone (polyurethane foam). To compare osseointegration, OMIs were placed in the tibia of 25 rabbits and the removal torque value was measured at 1, 2, 4, and 8 weeks after placement. The specimens were analyzed by optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS).

Results

The bone cutting capacity of the etched and hybrid group was lower than the machined (control) group, and was most inhibited in the RBM group (p < 0.05). At 4 weeks, the removal torque in the machined group was significantly decreased (p < 0.05), but was increased in the etched group (p < 0.05). In the hybrid group, the removal torque significantly increased at 2 weeks, and was the highest among all measured values at 8 weeks (p < 0.05). The infiltration of bone-like tissue surface was evaluated by SEM, and calcium and phosphorus were detected via EDS only in the hybrid group.

Conclusions

Partial RBM surface treatment (hybrid type in this study) produced the most stable self-drilling OMIs, without a corresponding reduction in bone cutting capacity.