Evaluation of antibacterial activity against Candida albicans according to the dosage of various denture cleansers

The antimicrobial activity of an antiseptic soap against Candida Albicans and Streptococcus Mutans single and dual-species biofilms on denture base and reline acrylic resins

To evaluate the effect of antiseptic soap on single and dual-species biofilms of Candida albicans and Streptococcus mutans on denture base and reline resins. Samples of the resins were distributed into groups (n = 9) according to the prevention or disinfection protocols. In the prevention protocol, samples were immersed in the solutions (Lifebuoy, 0.5% sodium hypochlorite solution and PBS) for 7, 14 and 28 days before the single and dual-species biofilms formation. Overnight denture disinfection was simulated. In the disinfection protocol, samples were immersed in the same solutions during 8 hours after the single and dual-species biofilms formation. Antimicrobial activity was analyzed by counting colony-forming units (CFU/mL) and evaluating cell metabolism. Cell viability and protein components of the biofilm matrix were evaluated using confocal laser scanning microscopy (CLSM). Data were submitted to ANOVA, followed by Tukey's post-test (α = 0.05) or Dunnett's T3 multiple comparisons test. In the prevention protocol, Lifebuoy solution effectively reduced the number of CFU/mL of both species. In addition, the solution decreased the cell metabolism of the microorganisms. Regarding disinfection protocol, the Lifebuoy solution was able of reduce approximately of 2-3 logs for all the biofilms on the denture base and reline resin. Cellular metabolism was also reduced. The images obtained with CLSM corroborate these results. Lifebuoy solution was effective in reducing single and dual-species biofilms on denture base and reline resins.

Effect of Denture Disinfectants on the Mechanical Performance of 3D-Printed Denture Base Materials

Denture care and maintenance are necessary for both denture longevity and underlying tissue health. However, the effects of disinfectants on the strength of 3D-printed denture base resins are unclear. Herein, distilled water (DW), effervescent tablet, and sodium hypochlorite (NaOCl) immersion solutions were used to investigate the flexural properties and hardness of two 3D-printed resins (NextDent and FormLabs) compared with a heat-polymerized resin. The flexural strength and elastic modulus were investigated using the three-point bending test and Vickers hardness test before (baseline) immersion and 180 days after immersion. The data were analyzed using ANOVA and Tukey's post hoc test (α = 0.05), and further verified by using electron microscopy and infrared spectroscopy. The flexural strength of all the materials decreased after solution immersion (p < 0.001). The effervescent tablet and NaOCl immersion reduced the flexural strength (p < 0.001), with the lowest values recorded with the NaOCl immersion. The elastic modulus did not significantly differ between the baseline and after the DW immersion (p > 0.05), but significantly decreased after the effervescent tablet and NaOCl immersion (p < 0.001). The hardness significantly decreased after immersion in all the solutions (p < 0.001). The immersion of the heat-polymerized and 3D-printed resins in the DW and disinfectant solutions decreased the flexural properties and hardness.

Evaluation of candida albicans adherence to CAD-CAM milled, 3D-printed, and heat-cured PMMA resin and efficacy of different disinfection techniques: an in-vitro study

PURPOSE

Candida albicans has been regarded as the most predominant oral fungal pathogen and the main cause of denture stomatitis. This study aimed to investigate C. albicans adherence to three types of denture base polymers: heat-cured polymethylmethacrylate (PMMA), CAD-CAM milled and 3D-printed. The efficacy of four common disinfection techniques, glutaraldehyde, brushing, microwave irradiation, and Polident overnight tablets, were also examined.

MATERIAL AND METHODS

Sixty blocks of pink acrylic specimens were fabricated from each polymer group. To investigate the C. albicans adherence, as well as the efficacy of different disinfection techniques on removing the yeast from the different materials, specimens were cultured within the fungal culture overnight followed by disinfection. The adhered C. albicans on the materials were then obtained by vortexing in phosphate buffered saline (PBS), and the numbers of the yeast in the suspensions were evaluated by measuring the optical density and/or colony-forming units on agar plates. Data were expressed as mean ± SEM (standard error of the mean). Statistical differences were evaluated by one-way analysis of variance (ANOVA) followed by the post-hoc Tukey HSD tests.

RESULTS

Significant differences in C. albicans adherence to the three polymers were noted. CAD-CAM milled and heat-cured PMMA showed significantly less C. albicans adherence compared with 3D printed PMMA. No significant difference was noted between milled and heat-cured PMMA. In the disinfection test, microwave irradiation, mechanical brushing, and Polident tablets were found to be effective in removing fungal attachment on the different denture materials, while glutaraldehyde was found to be the least effective.

CONCLUSION

C. albicans adherence to the polymers varies greatly based on the types of PMMA. 3D-printed had the highest fungal biofilm attachment. Microwave irradiation, mechanical brushing, and Polident overnight tablets had comparable results in removing C. albicans from all types of PMMA, while glutaraldehyde was not as effective. This article is protected by copyright. All rights reserved.