Flexural strength of a composite resin light cured with different exposure modes and immersed in ethanol or distilled water media

The Effects of Intensity, Exposure Time, and Distance of Polymerization Light on Vickers Microhardness and Temperature Rise of Conventional Resin-Based Composite

(1) Background: This study investigates the effects of curing light intensity, exposure time, and distance on the Vickers microhardness (VMH), hardness bottom-to-top ratio (HR), and temperature rise (TR) of conventional dental resin-based composite (RBC). (2) Materials and Methods: Specimens of one conventional RBC (Tetric EvoCeram, Ivoclar Vivadent) were cured with 12 different curing protocols (CPs), created with three different light intensities (Quartz Tungsten Halogen 300 mW/cm2, LED 650 mW/cm2, LED 1100 mW/cm2), two exposure times (20 and 40 s), and two distances of curing tip (0 and 8 mm). The VMH of top (VMH-T) and bottom (VMH-B) surfaces was measured. The hardness bottom-to-top ratio (HR) was calculated from VMH-B and VMH-T. The HR below 80% was rated as inadequate polymerization. The TR at the depth of 2 mm within the RBC was measured using a K-type thermocouple. Data were analyzed using Levene's test and the multivariate analysis of variance (MANOVA). The level of significance was set at p < 0.05. (3) Results: Exposure time and distance significantly influenced VMH-B and HR. Increased distance significantly reduced VMH-B, HR, and TR. CPs 300 mW/cm2/8 mm/20 s and 650 mW/cm2/8 mm/20 s produced inadequate polymerization (HR < 80%). Prolonged exposure time produced higher values of VMH-B and HR. The TR was significantly influenced by light intensity and distance. (4) Conclusions: Suboptimal light intensity (<800 mW/cm2) can produce inadequate polymerization at the lower side of the composite layer when used from a distance. Prolonged irradiation can improve the polymerization to a certain extent. Clinicians are advised to monitor the intensity of the LCUs in order to optimize the photopolymerization process. Caution is required when polymerizing with high-intensity curing light in direct contact with the RBC with longer exposure times than recommended.

How the Duration and Mode of Photopolymerization Affect the Mechanical Properties of a Dental Composite Resin

Composite materials are the most common materials in use in modern dentistry. Over the years, the methods of photopolymerization of composite materials have been improved with the use of various devices, such as quartz tungsten halogen lamps (QTHs), light-emitting diode units (LEDs), plasma-arc lamps and argon-ion lasers. This study aimed to compare the mechanical properties of a composite material, depending on the time and mode of photopolymerization. One hundred and forty rectangular specimens (25 × 2 × 2 mm) and forty-two disc-shaped samples (5 mm diameter and 2 mm thickness) were prepared from shade A2 Boston composite resin. Samples were cured using the following seven photopolymerization protocols: four fast-cure modes (full power for 3, 5, 10, and 20 s), two pulse-cure modes (5 and 10 shots of 1 s exposures at full power), and one step-cure mode (soft start with a progressive cycle lasting 9 s). Specimens were subjected to a flexural strength test, Vickers microhardness test, and FTIR spectroscopy test. A 2-factor ANOVA and post-hoc tests were carried out to assess the differences in the flexural strength parameter between the tested groups of samples before and after aging. A mixed-model ANOVA was carried out to assess the differences in the Vickers microhardness parameter between the tested groups of samples before and after aging. The lowest values of flexural strength (p < 0.001) and Vickers microhardness (p < 0.001) were obtained for the 3 s mode for the pre- and post-aging groups. The FTIR mapping tests showed a much more homogeneous chemical structure of the composite after 20 s of continuous irradiation, compared to the sample irradiated for 5 s in the continuous mode. The mode and cure time affects the mechanical properties of the composite resin. Appropriate selection of the cure mode and time ensures better mechanical properties of composite resin. This suggests that the survival of dental restorations within the oral cavity could be extended by using longer photopolymerization durations.

Comparison of Flexural Properties of Bulk-fill Restorative/Flowable Composites and Their Conventional Counterparts

The objectives of the study were to compare the flexural modulus and strength of restorative and flowable bulk-fill resin-based composites (RBCs) to their conventional counterparts and to determine the effects of conditioning environment on their flexural properties. The materials evaluated included three conventional RBCs (Filtek Z350, Tetric N Ceram, and Beautifil II), three restorative bulk-fill RBCs (Filtek Bulk-Fill Restorative, Tetric N Ceram Bulk-Fill, and Beautifil Bulk-fill Restorative), as well as three flowable bulk-fill RBCs (Filtek Bulk-Fill Flowable, Tetric N Flow Bulk-Fill, and Beautifil Bulk-Fill Flowable). Specimens were fabricated using customized stainless-steel molds, finished, measured, and randomly divided into four groups. The various RBCs were conditioned in the following mediums (n=10) for seven days at 37°C: air, artificial saliva (SAGF), 0.02 N citric acid, and 50% ethanol-water solution. After conditioning, the specimens were rinsed, blotted dry, measured, and subjected to flexural testing using a universal testing machine. Data were subjected to statistical analysis using analysis of variance and the Tukey test at a significance level of α = 0.05. Significant differences in flexural properties were observed between materials and conditioning mediums. Bulk-fill restorative RBCs exhibited higher flexural modulus than their bulk-fill flowable and conventional counterparts. With the exception of Filtek Bulk-Fill Flowable, bulk-fill flowable RBCs had significantly higher flexural strength than bulk-fill restorative and conventional RBCs. Flexural properties were highest when RBCs were conditioned in air and generally the lowest after exposure to ethanol.

Effect of radiant exposure and UV accelerated aging on physico-chemical and mechanical properties of composite resins

Currently, there is no consensus in terms of defining the minimum radiant exposure values necessary for achieving adequate properties of composite resin. In addition, the long-term influence that radiant exposure has on the properties of composite resins is still questionable. Objective: The objective of this study was to evaluate the effect of radiant exposure and UV accelerated aging on the physico-chemical and mechanical properties of micro-hybrid and nanofilled composite resins. Material and Methods: A nanofilled (Filtek Supreme; 3M ESPE) and a micro-hybrid composite resin (Filtek Z250; 3M ESPE) were investigated under different radiant exposures (3.75, 9, and 24 J/cm²) and UV accelerated aging protocols (0, 500, 1000, and 1500 aging hours). The degree of conversion (DC), flexural strength (FS), modulus (M), water sorption (WS), and solubility (WL) were evaluated. The results obtained were analyzed using two-way ANOVA and Tukey's test. Comparisons were performed using a significance level of α=0.05. Results: The DC, FS, and M were found to be significantly influenced by both radiant exposure and accelerated aging time. The DC and EM increased with radiant exposure in the no-aging group (0-hour aging) for both micro-hybrid and nanofilled composites, whereas no correlation was found after accelerated aging protocols. WS and WL of micro-hybrid and nanofilled composite resins were scarcely affected by radiant exposure (p>0.05), whereas they were significantly reduced by accelerated aging (p<0.001). Conclusions: Although increasing radiant exposure affected the degree of conversion and mechanical properties of micro-hybrid and nanofilled composites, no influence on the hydrolytic degradation of the material was observed. In contrast, UV accelerated aging affected both the physico-chemical and mechanical properties of the composites.

Impact of dietary solvents on flexural properties of bulk-fill composites

OBJECTIVE

This study investigated the effect of dietary solvents on flexural strength and modulus of bulk-fill composites.

MATERIALS AND METHODS

One conventional composite (Filtek Z350 [FZ]), two bulk-fill composites (Filtek Bulk-fill [FB] and Tetric N Ceram [TN]) and a bulk-fill giomer (Beautifil-Bulk Restorative [BB]) were evaluated. Specimens (12 × 2 × 2 mm) were fabricated using customized stainless steel molds. Specimens were light-cured, removed from their molds, finished, measured and randomly divided into six groups. The groups (n = 10) were conditioned in the following mediums for 7 days at 37 °C: air (control), artificial saliva (SAGF), distilled water, 0.02 N citric acid, heptane, 50% ethanol-water solution. After conditioning, the specimens were rinsed, blotted dry, measured and subjected to flexural testing using a universal testing machine. Representative SEM images of the intact surfaces were obtained to appraise the degradation mechanism by dietary solvents. Data was subjected to statistical analysis using ANOVA/Tukey's tests at significance level p < 0.05.

RESULTS

Significant differences in flexural properties were observed between materials and conditioning mediums. The highest flexural properties were usually obtained with conditioning in air (control) or heptane. Exposure to aqueous solutions generally reduced flexural properties of bulk-fill composites.

CONCLUSION

The effect of dietary solvents on flexural properties of bulk-fill composites was material and medium dependent.

Influence of different crosshead speeds on diametral tensile strength of a methacrylate based resin composite: An in-vitro study

Aim:

The aim was to evaluate the influence of different crosshead speeds on diametral tensile strength (DTS) of a resin composite material (Tetric N-Ceram).

Materials and Methods:

The DTS of Tetric N-Ceram was evaluated using four different crosshead speeds 0.5 mm/min (DTS 1), 1 mm/min (DTS 2), 5 mm/min (DTS 3), 10 mm/min (DTS 4). A total of 48 specimens were prepared and divided into four subgroups with 12 specimens in each group. Specimens were made using stainless steel split custom molds of dimensions 6 mm diameter and 3 mm height. The specimens were stored in distilled water at room temperature for 24 h. Universal testing machine was used and DTS values were calculated in MPa.

Results:

Analysis of variance was used to compare the four groups. Higher mean DTS value was recorded in DTS 2 followed by DTS 4, DTS 1, and DTS 3, respectively. However, the difference in mean tensile strength between the groups was not statistically significant (P > 0.05).

Conclusion:

The crosshead speed variation between 0.5 and 10 mm/min does not seem to influence the DTS of a resin composite.