Bulk-Fill Restorative Materials in Primary Tooth: An Intrapulpal Temperature Changes Study

Low and high viscosity bulk-fill composite resins stress distribution in primary molar tooth inlay cavity

The aim of this study is to evaluate the stress distributions of low and high viscosity bulk-fill composite resins at class II MOD inlay cavity in primary molar tooth using Finite Element Analysis (FEA). Original DICOM data of a primary molar tooth from a research archive was used to create a 3D model. Two models were prepared as Model 1: the tooth model without restoration (control group) and Model 2: the tooth model with class II MOD inlay restoration. Two different bulk-fill composite resins were tested in study: Model 2 A (class II MOD inlay cavity model restored with low viscosity bulk-fill composite resin) and Model 2B (class II MOD inlay cavity model restored with high viscosity bulk-fill composite resin). Occlusal vertical loading of 232 N was applied to the teeth in occlusal contact areas. Maximum Von Mises stress values in the models for enamel, dentin, and restorative material were evaluated as MPa. More intense stress accumulation is observed in enamel than in dentin. In addition, more stress values were determined in Model 2B (206.15 MPa, 32.76 MPa, 128.95 MPa) than in Model 2 A (203.39 MPa, 29.77 MPa, 120.61 MPa) for enamel, dentin and restorative material, respectively.

Thickness-Dependent Light Transmittance and Temperature Rise in Dual-Cure Bioactive and Light-Cure Bulk-Fill Composite Resins

This study aimed to assess the light transmittance (T) and temperature increase through different increments of dual-cure bioactive bulk-fill restorative material (ACTIVA), light-cure bulk-fill, and conventional composite resin materials. Cylindrical specimens with a diameter of 8 mm and heights of 1, 2, 3, and 4 mm of ACTIVA, Tetric-N-Ceram bulk-fill (TBF), Filtek One bulk-fill (FBF), and Filtek Z250 (FZ) (n = 6 per group, 96 in total) were light-cured with a visible blue low-intensity light-emitting diode (LED) (650-800 mW/cm² irradiance). T, and the temperature increase, were measured using an optical power meter and a digital thermometer during curing. The T mean values ranged between 0.012 and 0.239 (76.02 to 98.81% light attenuation), while the temperature rise mean values ranged between 9.02 and 20.80 °C. The parameters, including material type (partial eta squared (ηp²) = 0.284, p < 0.0001), thickness (ηp² = 0.284, p < 0.0001), and their interaction (ηp² = 0.185, p = 0.047), significantly affected the T values, whereas only the material type (ηp² = 0.352, p = 0.047) affected the temperature rise values. The T and temperature rise mean values were highest in ACTIVA increments of 1-mm increments, in particular, showing the highest T mean values, followed by similar increments of TBF. A significantly higher T was found in 1-mm increments compared to thicker increments for all materials (p < 0.0001), and a significant positive correlation existed between T and temperature rise values (r = 0.348, p = 0.001). These findings show that the bioactive material ACTIVA and TBF allow for better T than the other materials, with ACTIVA recording a higher temperature rise. However, the large light attenuation observed for all materials, irrespective of thickness, suggests that curing in more than one location with a low-intensity LED is necessary to optimize the curing process. Furthermore, incremental filling of bulk-fill materials using a low intensity LED could be beneficial.

Does the heat generated by fluorescence-aided caries excavation system effect the pulp temperature of primary teeth irreversibly? An in-vitro evaluation of the temperature changes in the pulp chamber

Background

This study aimed to analyze the effect of the Fluorescence Aided Caries Excavation (FACE) and the remaining dentin thickness on the temperature changes of the pulp chamber.

Material and Methods

Freshly extracted deciduous molars and a pulpal microcirculation model were used in the study. The sample size was calculated according to power analyses (power at 90%) based on previous studies. Thus, 40 samples were needed. Standard cavities (3x3 mm) were designed to obtain a 2 mm distance through to the pulp chamber, and in each tooth (n=10), these cavities were modified to obtain 1.5 mm, 1mm, and 0.5 mm final distance through to the pulp. Coronal parts of the teeth were placed on an acrylic plate with three gaps for feeding and extraction needles and the thermocouple. The temperature changes were recorded from the initial time to 15 s and 30 s,1 min, 1.5 min, 2 min, 2.5 min, 3 min intervals.

Results

The results showed that hence the thickness between cavity floor and pulp chamber was decreased, and application time of FACE was increased, an increase in temperature changes was detected. However, the recorded values were not mean to cause irreversible damages to the pulp chamber.

Conclusions

The recent study showed that Face is an appropriate caries detecting system that does not affect the pulp chamber's health, and it can be safely used in the primary teeth. Key words:Caries assessment, dental caries, dental pulp, pediatric dentistry.

Temperature increases in primary teeth pulp chamber during polymerization of glass ionomer-based restorative materials

Purpose

To evaluate the temperature changes in primary teeth pulp chambers of different dentin thicknesses during polymerization of four glass ionomer-based restorative materials.

Materials and methods

Eighty extracted, caries‑free, primary molars were prepared as standardized Class I occlusal cavities with dentin thicknesses of 1 mm and 2 mm. Four glass ionomerbased restorative materials, Dyract XP, Photac Fil Quick Aplicap, Fuji II LC, and GCP Glass Fill, were placed in the cavities and cured with two light-curing units. Temperature increases (initial temperature, 37°C) in the pulp chamber during polymerization were recorded by a J-type thermocouple in a pulpal microcirculation set-up. The data were analyzed with Variance analyses and Tukey tests.

Results

The temperatures recorded in samples with dentin thicknesses of 1 mm and 2 mm exhibited statistically significant differences (p<0.05). The GCP Glass Fill group exhibited the highest temperature increases for both dentin thicknesses (p<0.05). The other groups were not statistically different but the Dyract XP group exhibited the least temperature change.

Conclusion

The highest temperature changes were observed for 1 mm dentin thickness. All temperature increases during polymerizations and setting reactions were lower than the corresponding critical values 5.5°C.

Flowable Bulk-Fill Materials Compared to Nano Ceramic Composites for Class I Cavities Restorations in Primary Molars: A Two-Year Prospective Case-Control Study

Background: The aim of this split-mouth study is to compare the results of 24 months’ clinical performance of primary molar Class I restorations with a nano-ceramic composite, Ceram•X mono (Dentsply) with a flowable bulk-fill material regular viscosity, SDR (Dentsply). Methods: Following the ethical approval, 27 patients with at least two class I cavities in primary molars were included in the study. A total number of 54 restorations were conducted (n = 27 for Ceram X and n = 27 for SDR). Restorations were evaluated at baseline, 6, 18, and 24 months, according to the modified Ryge criteria. The cavosurface marginal discoloration and color match were evaluated visually after air-drying the tooth and after removing the plaque (if necessary). Results: At 24 months’ follow-up, 54 restorations showed similar clinical performance. The statistical analysis did not reveal any statistical significance in the values between the groups in 7 out of 7 modified Ryge criteria. However, two restorations in both groups received Bravo ratings in the cavosurface marginal discoloration scoring. No side effects were reported by the participants of the study. Conclusion: Restorations with both materials (Ceram•X mono and SDR) have provided almost identical results.

Erratum: Bulk-Fill Restorative Materials in Primary Tooth: An Intrapulpal Temperature Changes Study

[This corrects the article on p. S52 in vol. 9, PMID: 29962764.].