A comparison of different osteotomy techniques with and without pterygomaxillary disjunction in surgically assisted maxillary expansion utilizing modified hybrid rapid maxillary expansion device with posterior implants: A finite element study

Can different osteotomies have an influence on surgically assisted rapid maxillary expansion? A systematic review

The purpose of this study was to systematically review the randomized and non-randomized clinical trials (RCT; nRCT) concerning the different available osteotomies for surgically assisted rapid maxillary expansion (SARME): pterygomaxillary disjunction (SARME + PD vs SARME-PD) and segmental Le Fort I osteotomy (2-piece vs 3-piece). Outcomes focused on skeletal, dental, upper airway changes, complications, and relapse. Two authors investigated five databases (PubMed, Cochrane Library, Google Scholar, Scopus, Web of Science) until August 2023. The Cochrane Collaboration Tool and the Newcastle-Ottawa scale were used for the quality assessment of the included RCTs and nRCTs, respectively. A total of 554 articles were retrieved and after duplicates removing and full-text reading, 40 studies were included. Two RCTs showed a low risk of bias, one an unclear risk and one a high risk. Among the non-RCTs, 15 studies showed a good quality, while 21 exhibited a fair quality score. SARME + PD resulted in more homogeneous posterior bone expansion, with minimal dental effects. No difference between 2-piece and 3-piece in asymmetric expansion was observed, although 3SO showed 1-2 mm of more transverse increase. The oropharynx minimum cross-sectional area, the nasopharynx and the oropharynx volume were greater in SARME + PD. Both dental and bone relapse can occur but no differences between the groups were observed. All osteotomies guaranteed a correction of transverse maxillary deficiency. Lower side effects were described in SARME + PD. Two-piece and 3-piece segmental Le Fort I osteotomies did not show any differences in the symmetry and amount of expansion.

Effect of different palatal expanders with miniscrews in surgically assisted rapid palatal expansion: A non-linear finite element analysis

INTRODUCTION

Surgically assisted rapid palatal expansion (SARPE) has been the treatment of choice in subjects presenting skeletally mature sutures.

OBJECTIVE

The purpose of this study was to analyze stress distribution and displacement of the craniofacial and dentoalveolar structures resulting from three types of palatal expanders with surgical assistance using a non-linear finite element analysis.

MATERIAL AND METHODS

Three different palatal expanders were designed: Model-I (tooth-bone-borne type containing four miniscrews), Model-II (tooth-bone-borne type containing two miniscrews), and Model-III (bone-borne type containing four miniscrews). A Le Fort I osteotomy was performed, and a total of 5.0 mm palatal expansion was simulated. Nonlinear analysis (three theory) method (geometric nonlinear theory, nonlinear contact theory, and nonlinear material methods) was used to evaluate stress and displacement of several craniofacial and dentoalveolar structures.

RESULTS

Regardless of the maxillary expander device type, surgically assisted rapid palatal expansion produces greater anterior maxillary expansion than posterior (ANS ranged from 2.675 mm to 3.444 mm, and PNS ranged from 0.522 mm to 1.721 mm); Model-I showed more parallel midpalatal suture opening pattern - PNS/ANS equal to 54%. In regards to ANS, Model-II (1.159 mm) and Model-III (1.000 mm) presented larger downward displacement than Model-I (0.343 mm). PNS displaced anteriorly more than ANS for all devices; Model-III presented the largest amount of forward displacement for PNS (1.147 mm) and ANS (1.064 mm). All three type of expanders showed similar dental displacement, and minimal craniofacial sutures separation. As expected, different maxillary expander designs produce different primary areas and levels of stresses (the bone-borne expander presented minimal stress at the teeth and the tooth-bone-borne expander with two miniscrews presented the highest).

CONCLUSIONS

Based on this finite element method/finite element analysis, the results showed that different maxillary expander designs produce different primary areas and levels of stresses, minimal displacement of the craniofacial sutures, and different skeletal V-shape expansion.