An Update on Nickel-Titanium Rotary Instruments in Endodontics: Mechanical Characteristics, Testing and Future Perspective-An Overview

Since the introduction of Nickel-Titanium alloy as the material of choice for the manufacturing of endodontic rotary instruments, the success rate of the root canal therapies has been significantly increased. This success mainly arises from the properties of the Nickel-Titanium alloy: the biocompatibility, the superelasticity and the shape memory effect. Those characteristics have led to a reduction in time of endodontic treatments, a simplification of instrumentation procedures and an increase of predictability and effectiveness of endodontic treatments. Nevertheless, the intracanal separation of Nickel-Titanium rotary instruments is still a major concern of endodontists, with a consequent possible reduction in the outcome rate. As thoroughly demonstrated, the two main causes of intracanal separation of endodontic instruments are the cyclic fatigue and the torsional loads. As results, in order to reduce the percentage of intracanal separation research and manufacturers have been focused on the parameters that directly or indirectly influence mechanical properties of endodontic rotary instruments. This review describes the current state of the art regarding the Nickel-Titanium alloy in endodontics, the mechanical behavior of endodontic rotary instruments and the relative stresses acting on them during intracanal instrumentation, highlighting the limitation of the current literature.

Angle of Insertion and Torsional Resistance of Nickel-Titanium Rotary Instruments

Previously published studies have investigated the influence of instrument access on cyclic fatigue resistance. However, no studies have evaluated the relationship between angulated access and torsional resistance. The aim of this study was to investigate the influence of the angle of access on the torsional resistance of endodontic instruments. One hundred and eighty instruments were selected: 90 F-One Blue 25/04 and 90 HeroShaper 25/04 instruments. Three subgroups (n = 30) for each instrument type (A and B) were established according to the angle of insertion of the instruments inside the artificial canal (0°, 10° and 20°). The tests were performed using a custom-made device consisting of the following: a motor that can record torque values of 0.1 s; interchangeable stainless-steel canals with different curvature (0°, 10° and 20°) that allow the instrument’s angulated insertion and keep it flexed during testing procedures; and a vise used to secure the instrument at 3 mm from the tip. Torque limit was set to 5.5 Ncm, and each instrument was rotated at 500 rpm until fracture occurred. Torque to fracture (TtF) was registered by the endodontic motor, and the fragment length (FL) was measured with a digital caliper. Fractographic analysis was performed using a scanning electron microscopy (SEM) evaluation to confirm the cause of failure. TtF values and fragment length (FL) values were statistically analyzed using one-way analysis of variance (ANOVA) test and the Bonferroni correction for multiple comparisons across the groups with significance set to a 95% confidence level. Regarding the F-One Blue instruments, the results showed a higher TtF for group A3 (20°) than for group A1 (0°) and group A2 (10°), with a statistically significant difference between group A3 and the other two groups (p < 0.05), whereas no statistically significant difference was found between group A1 and group A2 (p > 0.05). Regarding the HeroShaper instrument, the results showed the highest TtF for group B3, with a statistically significant difference between the three subgroups B1, B2 and B3 (p < 0.05). The results showed that the torsional resistance increases as the angle of instrument access increases with a varying intensity, according to the crystallographic phase of the instrument selected.

A Paradigm Shift for Torsional Stiffness of Nickel-Titanium Rotary Instruments: A Finite Element Analysis

INTRODUCTION

The aim of this study was to investigate the influence of mass and the polar moment of inertia on the torsional behavior of nickel-titanium rotary instruments to understand which parameter of cross-sectional design had a key role in terms of torsional resistance.

METHODS

Four different instrument models were designed and meshed using computer-aided engineering software (SolidWorks; Dassault Systems, Waltham, MA). Instrument models shared the same characteristics, except for cross-sectional design; triangle, rectangle, square, and hollow square geometry was selected. Finite element analysis was performed simulating a static torsional test using the FEEPlus internal solver (Solid Works). Von Mises stress and torsional load at fracture were calculated by the software. Linear regression analysis was performed to investigate the relationship of the polar moment of inertia, cross-sectional area, inner core radius, and mass per volume on the torsional resistance of nickel-titanium rotary instruments.

RESULTS

The polar moment of inertia positively affected the maximum torsional load with the highest level of correlation (R² = 0.917). It could be stated that the higher the polar moment of inertia is, the more maximum torsional load at fracture is present. Mass and cross-sectional area had a lower level of correlation compared with the polar moment of inertia (R² = 0.5533). According to this, 2 instruments with the same mass/mm and/or cross-sectional area could have different torsional resistance.

CONCLUSIONS

The polar moment of inertia can be considered as the most important cross-sectional factor in determining the torsional resistance of rotary instruments over metal mass and cross-sectional area.

An Update of the Possible Applications of Magnetic Resonance Imaging (MRI) in Dentistry: A Literature Review

This narrative review aims to evaluate the current evidence for the application of magnetic resonance imaging (MRI), a radiation-free diagnostic exam, in some fields of dentistry.

BACKGROUND

Radiographic imaging plays a significant role in current first and second level dental diagnostics and treatment planning. However, the main disadvantage is the high exposure to ionizing radiation for patients.

METHODS

A search for articles on dental MRI was performed using the PubMed electronic database, and 37 studies were included. Only some articles about endodontics, conservative dentistry, implantology, and oral and craniofacial surgery that best represented the aim of this study were selected.

RESULTS

All the included articles showed that MRI can obtain well-defined images, which can be applied in operative dentistry.

CONCLUSIONS

This review highlights the potential of MRI for diagnosis in dental clinical practice, without the risk of biological damage from continuous ionizing radiation exposure.