Clinical evaluation of conventional cantilever and resin bonded cantilever fixed partial dentures: a comparative study

Effect of four premolar extractions on the vertical dimension of the face : A retrospective cephalometric study

PURPOSE

Adequate control of the vertical dimension is of great importance in orthodontic treatment. Although existing evidence is very limited, extraction of four premolars is thought to contribute towards improved control of anterior facial height compared with non-extraction treatment protocols. Thus, the aim of this retrospective cohort study was to compare the effect of fixed-appliance treatment with extraction of four premolars to non-extraction treatment on the skeletal vertical dimension.

METHODS

A consecutive sample of 76 children with skeletal hyperdivergence (49% male; mean age 11.9 years) was divided into two groups for treatment with either non-extraction (n = 31) or extraction of four premolars (n = 45). Baseline characteristics were comparable: overjet 5.1 ± 2.5 mm, overbite 2.4 ± 1.9 mm, ANB angle 4.6 ± 2.3°, and SN-ML angle 40.2 ± 3.5°. Patients were treated with standard edgewise fixed appliances with closing loops/sliding mechanics. Vertical skeletal and dental outcomes were measured on lateral cephalograms before and after treatment. Data were analyzed with linear regression at 5%.

RESULTS

Compared to non-extraction treatment, treatment with premolar extractions had no significant effect on the SN-ML angle (difference (Δ) = 0.07°; 95% confidence interval -0.90 to 1.01°; P = 0.88). Statistically significant changes between the extraction and non-extraction groups were only found for the parameters SNA (Δ -1.47°; P = 0.003), ANB (Δ -1.17°; P = 0.004), SN-OP (Δ -1.48°; P = 0.04), and L1-ML (Δ -6.39°; P < 0.001).

CONCLUSION

Orthodontic treatment of children with skeletal hyperdivergence using systematic extraction of four premolars had minimal effects on the vertical facial dimension compared to non-extraction treatment.

Effect of different surface treatments and retainer designs on the retention of posterior Pd-Ag porcelain-fused-to-metal resin-bonded fixed partial dentures

The aim of this study was to investigate the adhesive property of palladium-silver alloy (Pd-Ag) and the simulated clinical performance of Pd-Ag porcelain-fused-to-metal (PFM), resin-bonded, fixed partial dentures (RBFPDs). A total of 40 Pd-Ag discs (diameter=5 mm) were prepared and divided into the following four groups (n=10): a) No sandblasting, used as a control; and b, 50 µm; c, 110 µm; and d, 250 µm aluminum oxide (Al₂O₃) particles, respectively. Another 50 discs were pre-sandblasted and divided into five groups (n=10) subjected to different treatments: e) Sandblasting, used as a control; f) silane; g) alloy primer; h) silica coating + silane and i) silica coating + alloy primer. All 90 discs were bonded to enamel with Panavia F 2.0 and then subjected to shear bond strength (SBS) testing. The fracture surfaces were examined by scanning electron microscopy. Next, 40 missing maxillary second premolar models were restored with one of the four following RBFPD designs (n=10): I) A premolar occlusal bar combined with molar double rests (MDR); II) both occlusal bars with a wing (OBB); III) a premolar occlusal bar combined with a molar dental band (MDB); and IV) two single rests adjacent to the edentulous space with a wing (SRB) used as a control. All specimens were aged with thermal cycling and mechanical loading. Subsequently, they were loaded until broken. The data were analyzed by one-way analysis of variance. Al₂O₃ (250 µm) abrasion provided the highest SBS (P<0.05). The alloy primer and silica + silane exhibited increased SBS. Furthermore, fracture analysis revealed that the failure mode varied among the different treatments. Whereas MDB exhibited the highest retention (P<0.05), that of OBB was greater than that of MDR (P<0.05), and the control exhibited the lowest retention. Abrasion with Al₂O₃ (250 µm) effectively increased the adhesive property of Pd-Ag. Additionally, treatment with the alloy primer and silica coating + silane was able to increase the adhesive property of abraded Pd-Ag. Under the present conditions, all three modified retainer types provided improved outcomes for Pd-Ag PFM RBFPDs compared with the control.