Effect of Mouthrinses containing Olive Oil, Fluoride, and Their Combination on Enamel Erosion: An in vitro Study

Preventive effect of chitosan gel containing CaneCPI-5 against enamel erosive wear in situ

OBJECTIVE

This study evaluated the preventive effect of a chitosan gel containing CaneCPI-5 against enamel erosion and erosion + abrasion in situ.

METHODS

Sixteen volunteers participated in a crossover, double-blind protocol, comprising 4 phases: (1) no treatment (Nt); (2) chitosan gel (Cg); (3) chitosan gel + 12,300 ppm NaF (Cg + NaF); and (4) chitosan gel + 0.1 mg/mL CaneCPI-5 (Cg + Cane). Volunteers wore an appliance containing 4 specimens. Once/day, they applied the gel (except for Nt) (4 min/specimen). Erosive challenges were performed extra-orally (0.1% citric acid, 90 s, 4 × /day; ERO). Specimens were also abraded (toothbrush, 15 s/specimen, 2 × /day; ERO + ABR). Enamel wear was assessed by profilometry and relative surface reflection intensity (%SRI). Two-way RM-ANOVA/Sidak's tests and Spearman's correlation were used (p < 0.05).

RESULTS

For profilometry, ERO + ABR promoted significantly greater wear when compared with ERO. There was a significant difference among all treatments. The lowest enamel loss occurred for Cg + Cane, followed by Cg + NaF, Cg, and Nt (p < 0.05). The %SRI was significantly lower for ERO + ABR when compared to ERO, only for the Nt group. The greatest %SRI was found for the Cg + NaF and Cg + Cane groups, which did not differ significantly, regardless of the conditions. The lowest %SRI was found for the Nt and Cg groups, which did not differ from each other, regardless of the conditions. The Nt group did not differ significantly from the Cg + NaF (ERO). There was a significant correlation between both analyses.

CONCLUSION

The incorporation of CaneCPI-5 in the chitosan gel prevented erosive wear in situ.

CLINICAL RELEVANCE

These results open a new perspective for the use of CaneCPI-5 in other application vehicles, such as chitosan gel.

Comparison of metrology created by profilometry and digital microscopy on polished dentine in an erosion/abrasion model

OBJECTIVE

Digital microscopy offers the ability to scan surfaces to produce 3D reconstructions, allowing step height measurements with high accuracy. The aims of this study were to compare the step heights from the gold standard, non-contact profilometry, to digital microscopy in an erosion/abrasion model.

METHODS

Dentine specimens (n = 60) were immersed in deionised water, 1450 ppm and 5000 ppm fluoride as sodium fluoride for 3 min, eroded for a total of 25 min in a cycled protocol in 0.3% citric acid (pH 2.7) and abraded with 120 and 240 brushing strokes. Samples were scanned by a non-contacting profilometer with a 0.1 μm vertical resolution and then the same samples imaged with a digital microscope and the step heights compared. Data were analysed in GraphPad Prism 7.00. Data were normally distributed and a 3 way ANOVA with post hoc analysis used to assess for differences between groups. Agreement between the measurement method was assessed using IntraClass Correlations and Bland Altmans plots.

RESULTS

The mean step heights from the profilometry and the digital microscope on the same samples were not statistically significant different. The magnitude of the differences was less than 0.5 μm. The results of the ANOVA demonstrated that the individual factors fluoride concentration and number of strokes were significant (P<0.05), however, the method of analysis was not (p = 0.74). ICC's between the two methods of analysis were excellent (0.996, p<0.001) with no proportional bias.

CONCLUSIONS

This study reports that step height on dentine from a digital microscopy and non-contact profilometry were not significantly different. The digital microscope, although slower, allows visual inspection of the samples as well as measurement.

SIGNIFICANCE

Digital microscope's offer the ability to scan, 2D or 3D images and perform meteorological analysis of samples. In this investigation both showed that 5000 ppm fluoride prevents erosive tooth wear in vitro.

In situ effect of a proanthocyanidin mouthrinse on dentin subjected to erosion

Proanthocyanidin has been shown to be efficient in inhibiting matrix metalloproteinases.