Titanium-hydroxyapatite composites sintered at low temperature for tissue engineering: in vitro cell support and biocompatibility

Physicochemical Characterization and Antibacterial Activity of Titanium/Shellac-Coated Hydroxyapatite Composites

Titanium and hydroxyapatite are widely used as materials for implants. Titanium has good mechanical properties, good corrosion resistance, and a high modulus of elasticity. Hydroxyapatite has good biocompatibility, bioactivity, and significant osteoinductivity. In this study, powder metallurgy was used as a method to combine titanium and hydroxyapatite for use in implants. Shellac was used as a binder between ceramic and metal due to its lower melting point. The surface morphology and chemical properties were evaluated by scanning electron microscopy–energy dispersive X-ray (SEM-EDX), whereby the SEM revealed the appearance of micropores in the Ti-HA composites during the sintering process, and the EDX showed that the final product had high amounts of Ti and Ca and low P. X-ray diffraction (XRD) and Fourier transform infrared (FTIR) analyses were used to achieve the chemical characterization of composites, whereby a weak diffraction peak was observed in the XRD spectrum of Ti-HA composites, and the FTIR analysis confirmed that the composites had carbonate (CO3)2−, phosphate (PO4)3−, and hydroxyl (OH)− groups. Oxygen was sufficient due to the sintering process being conducted in an air environment. The antibacterial activities were characterized using the disc diffusion method with Escherichia coli and Staphylococcus aureus bacteria, whereby the prepared Ti-HA composites had a greater antibacterial effect on E. coli than on S. aureus. Finally, pH changes were observed during the 24 h incubation. The result showed that the Ti-HA composite did not contain chemical compounds that could cause harmful effects for humans and had good antibacterial activity against E. coli.

Novel chitosan-poly(vinyl acetate) biomaterial suitable for additive manufacturing and bone tissue engineering applications

Chitosan, a biocompatible and biodegradable natural polymer, offers great promise as a biomaterial for tissue engineering applications. Chitosan scaffolds have previously been fabricated using additive manufacturing techniques, however, the use of crosslinkers, weak mechanical stability and structural resolution remain problematic. In this study Chitosan-PVAc biopolymer blends were prepared using a non-organic solvent that can prepare a three-dimensional printable biopolymer in less time than conventional methods. Prepared films were characterised using SEM, FTIR and thermogravimetric analysis. Additionally, the swelling properties, biodegradability and printability of the scaffolds were also studied. The fabricated films were biodegradable within a 3-week period and showed controllable swelling properties. Results indicated no toxicity and cells attached onto films. Additionally, hydrogels showed antibacterial activity against S. aureus, S. epidermidis and E.coli, which could potentially prevent implant related infections. Additive manufacturing simulation of PVAc composite 3% chitosan and PVAc composite 4% chitosan were able to produce a layered scaffold without using crosslinkers and therefore confirming printability. Cytocompabability were assessed using a resazurin assay and cell attachment. From these results, we concluded that the printable PVAc composite 3% chitosan and PVAc composite 4% chitosan biopolymer blends meet the requirements of a biomaterial and can potentially be used for biomedical implants.

Fabrication of Hydroxyapatite/Tantalum Composites by Pressureless Sintering in Different Atmosphere

The effect of sintering atmosphere (air and Ar) and temperature (1100, 1200, 1300 °C) on the microstructure, mechanical properties, and bioactivity of hydroxyapatite/tantalum (HA/Ta) composites were systematically investigated by pressureless sintering of the mixture of HA and Ta powders. It shows that the sintering atmosphere greatly impacts the phase composition and microstructure of the HA/Ta composites. The higher diffusion of atoms promotes shrinkage and causes deeper reaction fusion between the HA matrix and Ta, which improved the interfacial binding of the HA/Ta composites. The refined grain structure and improved interfacial binding obtained within the Ar atmosphere compared to the air atmosphere benefit the mechanical properties. The maximum bending strength and shrinkage observed for the composites sintered at 1300 °C in the Ar atmosphere are 27.24 MPa and 6.65%, respectively. The cell counting kit-8 (CCK-8) method was used to investigate the in vitro cytocompatibility of HA/Ta composites. The results revealed that the HA/Ta composites sintered with different conditions have no cytotoxicity. The simulated body fluid (SBF) soaking results showed that all of the studied composites possess desirable bioactivity, as demonstrated by their ability to form calcium-deficient carbonate apatite layer on the surfaces. For composites sintered at 1300 °C, the surface apatite layer coverage of the composites obtained in the Ar atmosphere was increased by 139.7% than the ones obtained in air, which confirmed an enhanced bioactive mineralization ability. The results indicated that the HA/Ta composites sintered at 1300 °C in Ar possess desirable mechanical properties and bioactivity. This work opens up the new possibility for preparing HA-based composites and is of great value in biomedical applications.

Surface properties and bioactivity of TiO2 nanotube array prepared by two-step anodic oxidation for biomedical applications

A highly ordered TiO₂ nanotube array has been prepared on a commercial pure titanium substrate in a hydrofluoric (HF) electrolyte using a DC power source through two-step anodic oxidation. The morphology, composition, wettability and surface energy of the nanotube array have been characterized by using a field-emission scanning electron microscope (FE-SEM), a transmission electron microscope (JEM-2010) with energy-dispersive X-ray spectrometer EDX (INCA OXFORD), X-ray diffraction method, an atomic force microscope (AFM), an optical contact angle measuring device and the Owens method with two liquids. The electrochemical behaviours of anodic oxidation films with different structures have been investigated in Sodium Lactate Ringer's Injection at 37±1°C by potentiodynamic polarization curve and electrochemical impedance spectroscopy. The formation mechanism of the nanotube array and the advantages of two-step oxidation have been discussed according to the experimental observation and the characterized results. Meanwhile, the structural changes of nanotubes are analysed according to the results of impedance spectroscopy. Cytotoxicity testing and cell adhesion and proliferation have been studied in order to evaluate the bioactivity of the nanotube array film. The diameters of nanotubes are in the range of 120-140 nm. The nanotube surface shows better wettability and higher surface energy compared to the bare substrate. The nanotube surface exhibits a wide passivation range and good corrosion resistance. The growth of the nanotube array is the result of the combined action of the anodization and field-assisted dissolution. The nanotube array by two-step oxidation becomes more regular and orderly. Moreover, the nanotube array surface is non-toxic and favourable to cell adhesion and proliferation. Such nanotube array films are expected to have significant biomedical applications.