Image-based Bone Density Classification Using Fractal Dimensions and Histological Analysis of Implant Recipient Site

Pilot study of fractal dimension analysis of osteogenesis for bone substitute materials of Bio-Oss in lateral sinus augmentation

BACKGROUND

Fractal dimension (FD) analysis has been proposed and validated in osseointegration-related research. The aim of this study was to evaluate the feasibility of FD analysis in the osteogenesis detection of bone substitute materials (BSMs) of Bio-Oss in maxillary lateral sinus augmentation.

METHODS

Patients who received lateral maxillary sinus augmentation and underwent grafting with BSMs (Bio-Oss) were included in the study. The cross sections of the BSMs under cone-beam computed tomography (CBCT) at mesial, distal, and sagittal directions were obtained immediately after the graft (T0) and 6 months later (T1), and the obtained images were cropped to include only the BSMs. The FD analysis was performed, and the FD value was obtained by the method of box-counting. Paired t-tests and analysis of variance (ANOVA) were used, and p-values <0.05 was considered statistically significant.

RESULTS

Twelve participants with 22 implants, which were inserted simultaneously after sinus augmentation, were included in this study. A total of 22 mesial, 22 distal, and 14 sagittal images were obtained after FD analysis. The mean FD value and standard deviation at T0 was 1.2860 ± 0.0896, while at T1, it was 1.2508±0.1023; thus, significant differences were detected (p = 0.022). However, the increasing or decreasing trend of FD value was not stable, and no significant difference was detected for FD values of mesial, distal, and sagittal images between T0 and T1. ANOVA indicated that no significant difference was detected among the FD values of mesial, distal, and sagittal images at any timepoint. Differences in FD values between the sexes were not significant either.

CONCLUSIONS

Since the FD analysis for the osteogenesis detection of BSMs in maxillary sinus augmentation indicated unstable trends of change, its feasibility is not reliable. The initially rough surface, self-degradation, and volume change of the BSMs during osteogenesis may be the reason for the variation in FD values.

Mechanical Behaviour and Primary Stability of a Self-Condensing Implant: A Laboratory Critical Simulation of a Severe Maxillary Atrophy on Polyurethane Lamina

Background: Posterior maxillary atrophies could emerge after the loss of teeth, trauma, infections, or lesions that often require regenerative approaches. In these critical conditions, the achievement of implant primary stability represents a clinical challenge in the operative practice. Therefore, a two-stage approach is often preferred with a delay of the rehabilitation time and a consistent increasing of the biological and the operative costs. The aim of this study was to evaluate the mechanical behaviour of a self-condenser implant compared to a standard implant in a critical simulation on different thicknesses and densities of polyurethane lamina. Materials and methods: A total of two implant models were tested: a self-condensing device (test) and a standard implant (control). The study evaluated the insertion torque and the pull-out strength values of the test and control implants inserted in different sizes (1, 2, and 3 mm) and density polyurethane lamina (10, 20, and 30 pcf) for a total of 320 experimental sites. Results: In total, 320 experimental sites were produced in the polyurethane samples. A statistically significant difference of insertion and pull-out torque values between the test and control Implants was found in the different bone densities (p < 0.05). The insertion and pull-out torque values were always higher for the test implants in all experimental conditions. In all bone densities, the insertion torque values were higher than the pull-out torque values. The self-condenser dental implant design evaluated in this in vitro study showed a high level of stability in all experimental conditions. Conclusions: The test implant could represent a useful tool for a one-stage surgical approach in the presence of limited residual native bone as an alternative to a delayed technique.

Application of Texture and Fractal Dimension Analysis to Evaluate Subgingival Cement Surfaces in Terms of Biocompatibility

Biocompatibility is defined as “the ability of a biomaterial, prosthesis, or medical device to perform with an appropriate host response in a specific application”. Biocompatibility is especially important for restorative dentists as they use materials that remain in close contact with living tissues for a long time. The research material involves six types of cement used frequently in the subgingival region: Ketac Fil Plus (3M ESPE, Germany), Riva Self Cure (SDI, Australia) (Glass Ionomer Cements), Breeze (Pentron Clinical, USA) (Resin-based Cement), Adhesor Carbofine (Pentron, Czech Republic), Harvard Polycarboxylat Cement (Harvard Dental, Great Britain) (Zinc polycarboxylate types of cement) and Agatos S (Chema-Elektromet, Poland) (Zinc Phosphate Cement). Texture and fractal dimension analysis was applied. An evaluation of cytotoxicity and cell adhesion was carried out. The fractal dimension of Breeze (Pentron Clinical, USA) differed in each of the tested types of cement. Adhesor Carbofine (Pentron, Czech Republic) cytotoxicity was rated 4 on a 0–4 scale. The Ketac Fil Plus (3M ESPE, Germany) and Riva Self Cure (SDI, Australia) cements showed the most favorable conditions for the adhesion of fibroblasts, despite statistically significant differences in the fractal dimension of their surfaces.