Removal of Trace Pharmaceuticals from Water using coagulation and powdered activated carbon as pretreatment to ultrafiltration membrane system

In this study, the efficacy of water treatment technologies: ultra-filtration (UF), powdered activated carbon (PAC), coagulation (COA) and a combination of these technologies (PAC/UF and COA/UF) to remove target pharmaceuticals (Acetaminophen, Bezafibrate, Caffeine, Carbamazepine, Cotinine, Diclofenac, Gemfibrozil, Ibuprofen, Metoprolol, Naproxen, Sulfadimethoxine, Sulfamethazine, Sulfamethoxazole, Sulfathiazole, Triclosan and Trimethoprim) was investigated. Samples of wastewater from municipal WWTPs were analyzed using direct aqueous injection High Performance Liquid Chromatography with Tandem Quadrupole Mass Spectrometric (LC/MS/MS) detection. On concentration basis, results showed an average removal efficiency of 29%, 50%, and 7%, respectively, for the UF, PAC dosage of 50ppm, and COA dosage of 10ppm. When PAC dosage of 100ppm was used as pretreatment to the combined PAC and UF in-line membrane system, a 90.3% removal efficiency was achieved. The removal efficiency of UF in tandem with COA was 33%, an increase of 4% compared with the single UF treatment. The adsorption effect of PAC combined with the physical separation process of UF revealed the best treatment strategy for removing pharmaceutical contaminant from water.

Local heating with lithographically fabricated plasmonic titanium nitride nanoparticles

Titanium nitride is considered a promising alternative plasmonic material and is known to exhibit localized surface plasmon resonances within the near-infrared biological transparency window. Here, local heating efficiencies of disk-shaped nanoparticles made of titanium nitride and gold are compared in the visible and near-infrared regions numerically and experimentally with samples fabricated using e-beam lithography. Results show that plasmonic titanium nitride nanodisks are efficient local heat sources and outperform gold nanodisks in the biological transparency window, dispensing the need for complex particle geometries.

Meeting world's most stringent Hg criterion: a pilot-study for the treatment of oil refinery wastewater using an ultrafiltration membrane process

A membrane ultrafiltration (UF) technology was tested using an oil refinery's end-of-pipe effluent to demonstrate the proof of concept, i.e. can the Great Lakes Initiative criterion of less than 1.3 ppt be consistently met at the pilot-scale, and to provide the data necessary for preliminary full-scale process design. This study presents the successful pilot test conducted with continuous but varying feed conditions over a protracted period. The UF membrane process consistently provided a constant permeate quality at all tested operating conditions, virtually independent of the feed water characteristics and the feed Hg concentration (0.5-22.7 ppt). The treatment target of less than 1.3 ppt of Hg was met and exceeded for all tested conditions during the pilot study. Turbidity measurements were <0.5 NTU (with a MDL of 0.5 NTU) 85% of the time and <0.16 NTU 95% of the time when analyzed on-line. The TMP values were below the specification of (negative) 7-12 psi at all tested conditions during the pilot-study. Weekly maintenance cleans and monthly clean in place (CIP) events were very effective in consistently restoring the membrane permeability during the pilot-study.

Analyzing the spatial and temporal characteristics of membrane fouling

Fouling characteristics of crossflow flat-sheet membranes for two Nanofiltration (NF), one Ultrafiltration (UF), and one Microfiltration (MF) membranes were analyzed using 12.5 parts per million (mg/L) FeCl3 solution and 350 mg/L copper nanofluid. FeCl3 solution represents dissolved contaminant whereas copper nanofluid simulates particulate contaminant. The spatial and temporal fouling evolutions were captured using digital photography and analyzed using ImageJ software. FeCl3 fouling studies for one NF membrane showed uniform fouling whereas for the other NF membrane, isolated fouling was apparent and the fouling initiated at the outlet then gradually extended towards the inlet. Copper nanoparticle fouling studies analyzed through gravimetric and image processing revealed spatial and temporal fouling developments. Both non-equilibrium and equilibrium fouling stages/regions were evaluated through fouling density analysis.

Fabrication and calibration of oxazine-based optic fiber sensor for detection of ammonia in water

This paper presented the fabrication and calibration of a clad-modified evanescent based plastic optical fiber (POF) sensor for the detection of ammonia in both stagnant and dynamic aqueous media. This optochemical sensor was based on Oxazine 170 perchlorate (sensing material) and polydimethylsiloxane (PDMS) (protective material) thin layers. A special chemical solution was developed for the etching removal of cladding and a methodology for trapping moisture was exercised. Experimental results on dissolved ammonia detection exhibited short response time (≤10 s), low detection limit (minimum detection limit 1.4 ppm), high sensitivity, and excellent reversibility (over 99%).