1
|
Zhao H, Wang Y, Wang Y, Gong H, Yinjun F, Cui X, Zhang J, Huang W. [Embedded 3D printing of porous silicon orbital implants and its surface modification]. Nan Fang Yi Ke Da Xue Xue Bao 2023; 43:783-792. [PMID: 37313820 DOI: 10.12122/j.issn.1673-4254.2023.05.14] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [What about the content of this article? (0)] [Affiliation(s)] [Abstract] [Key Words] [Subscribe] [Scholar Register] [Indexed: 06/15/2023]
Abstract
OBJECTIVE To prepare customized porous silicone orbital implants using embedded 3D printing and assess the effect of surface modification on the properties of the implants. METHODS The transparency, fluidity and rheological properties of the supporting media were tested to determine the optimal printing parameters of silicone. The morphological changes of silicone after modification were analyzed by scanning electron microscopy, and the hydrophilicity and hydrophobicity of silicone surface were evaluated by measuring the water contact angle. The compression modulus of porous silicone was measured using compression test. Porcine aortic endothelial cells (PAOECs) were co-cultured with porous silicone scaffolds for 1, 3 and 5 days to test the biocompatibility of silicone. The local inflammatory response to subcutaneous porous silicone implants was evaluated in rats. RESULTS The optimal printing parameters of silicone orbital implants were determined as the following: supporting medium 4% (mass ratio), printing pressure 1.0 bar and printing speed 6 mm/s. Scanning electron microscopy showed that the silicone surface was successfully modified with polydopamine and collagen, which significantly improved hydrophilicity of the silicone surface (P < 0.05) without causing significant changes in the compression modulus (P > 0.05). The modified porous silicone scaffold had no obvious cytotoxicity and obviously promoted adhesion and proliferation of PAOECs (P < 0.05). In rats bearing the subcutaneous implants, no obvious inflammation was observed in the local tissue. CONCLUSION Poprous silicone orbital implants with uniform pores can be prepared using embedded 3D printing technology, and surface modification obviously improves hydrophilicity and biocompatibility of the silicone implants for potential clinical application.
Collapse
Affiliation(s)
- H Zhao
- Department of Human Anatomy, School of Basic Medical Sciences, Guangdong Medical University, Dongguan Key Laboratory of Stem Cell and Regenerative Tissue Engineering, Dongguan 523808, China
- National Key Discipline of Human Anatomy, School of Basic Medical Sciences, Southern Medical University, Guangdong Provincial Key Laboratory of Digital Medical and Biomechanics, Guangdong Engineering Research Center for Translation of Medical 3D Printing Application, Guangzhou 510515, China
| | - Y Wang
- National Key Discipline of Human Anatomy, School of Basic Medical Sciences, Southern Medical University, Guangdong Provincial Key Laboratory of Digital Medical and Biomechanics, Guangdong Engineering Research Center for Translation of Medical 3D Printing Application, Guangzhou 510515, China
| | - Y Wang
- Guangdong Provincial People's Hospital Affiliated to Southern Medical University, Guangdong Academy of Medical Science, Guangzhou 510080, China
| | - H Gong
- National Key Discipline of Human Anatomy, School of Basic Medical Sciences, Southern Medical University, Guangdong Provincial Key Laboratory of Digital Medical and Biomechanics, Guangdong Engineering Research Center for Translation of Medical 3D Printing Application, Guangzhou 510515, China
| | - F Yinjun
- National Key Discipline of Human Anatomy, School of Basic Medical Sciences, Southern Medical University, Guangdong Provincial Key Laboratory of Digital Medical and Biomechanics, Guangdong Engineering Research Center for Translation of Medical 3D Printing Application, Guangzhou 510515, China
| | - X Cui
- Department of Human Anatomy, School of Basic Medical Sciences, Guangdong Medical University, Dongguan Key Laboratory of Stem Cell and Regenerative Tissue Engineering, Dongguan 523808, China
| | - J Zhang
- Department of Human Anatomy, School of Basic Medical Sciences, Guangdong Medical University, Dongguan Key Laboratory of Stem Cell and Regenerative Tissue Engineering, Dongguan 523808, China
| | - W Huang
- Department of Human Anatomy, School of Basic Medical Sciences, Guangdong Medical University, Dongguan Key Laboratory of Stem Cell and Regenerative Tissue Engineering, Dongguan 523808, China
- National Key Discipline of Human Anatomy, School of Basic Medical Sciences, Southern Medical University, Guangdong Provincial Key Laboratory of Digital Medical and Biomechanics, Guangdong Engineering Research Center for Translation of Medical 3D Printing Application, Guangzhou 510515, China
| |
Collapse
|