Coaxial Dielectric Spectroscopy as an In-Line Process Analytical Technique for Reaction Monitoring

The suitability of broadband dielectric spectroscopy (DS) as a tool for in-line (in situ) reaction monitoring is demonstrated. Using the esterification of 4-nitrophenol as a test-case, we show that multivariate analysis of time-resolved DS data-collected across a wide frequency range with a coaxial dip-probe-allows reaction progress to be measured with both high precision and high accuracy. In addition to the workflows for data collection and analysis, we also establish a convenient method for rapidly assessing the applicability of DS to previously untested reactions or processes. We envisage that, given its orthogonality to other spectroscopic methods, its low cost, and its ease of implementation, DS will be a valuable addition to the process chemist's analytical toolbox.

Ring opening polymerisation of ɛ-caprolactone with novel microwave magnetic heating and cyto-compatible catalyst

We report on the ring-opening polymerization of ɛ-caprolactone incorporated with a magnetic susceptible catalyst, FeCl₃, via the use of microwave magnetic heating (HH) which primarily heats the bulk with a magnetic field (H-field) from an electromagnetic field (EMF). Such a process was compared to more commonly used heating methods, such as conventional heating (CH), i.e., oil bath, and microwave electric heating (EH), which is also referred to as microwave heating that primarily heats the bulk with an electric field (E-field). We identified that the catalyst is susceptible to both the E-field and H-field heating, and promoted the heating of the bulk. Which, we noticed such promotion was a lot more significant in the HH heating experiment. Further investigating the impact of such observed effects in the ROP of ɛ-caprolactone, we found that the HH experiments showed a more significant improvement in both the product Mwt and yield as the input power increased. However, when the catalyst concentration was reduced from 400:1 to 1600:1 (Monomer:Catalyst molar ratio), the observed differentiation in the Mwt and yield between the EH and the HH heating methods diminished, which we hypothesized to be due to the limited species available that were susceptible to microwave magnetic heating. But comparable product results between the HH and EH heating methods suggest that the HH heating method along with a magnetic susceptible catalyst could be an alternative solution to overcome the penetration depth problem associated with the EH heating methods. The cytotoxicity of the produced polymer was investigated to identify its potential application as biomaterials.

Evaluation of Microwave Applicator Design on Electromagnetic Field Distribution and Heating Pattern of Cooked Peeled Shrimp

Non-uniform temperature distribution within solid food is a major problem associated with microwave heating, which limits industrial applications. Therefore, an experimentally validated 3D model was proposed to study the effect of microwave applicator geometry on the electromagnetic field distribution and heating pattern of shrimp under different processing conditions. Simulation results were compared with physical experiments, in which a cooked peeled shrimp sample was heated using two different laboratory-scale microwave applicators (rectangular and cylindrical cavities). For the rectangular applicator, the temperature distribution within the shrimp, when examined in cross-section, was more homogeneous compared to that of the cylindrical applicator. The results showed the influence of the complex shape of the food on the temperature distribution during microwave heating, as well as of process parameters (input power and geometry cavity). Moreover, this modelling method could provide a better understanding of the microwave heating process and assist manufacturing companies to evaluate a suitable microwave applicator according to their specific purpose.

The importance of ionic conduction in microwave heated polyesterifications

Significant increases in the reaction rate and final conversion of a model polyesterification are reported by the use of microwave heating.

Validating a Predictive Structure-Property Relationship by Discovery of Novel Polymers which Reduce Bacterial Biofilm Formation

Synthetic materials are an everyday component of modern healthcare yet often fail routinely as a consequence of medical-device-centered infections. The incidence rate for catheter-associated urinary tract infections is between 3% and 7% for each day of use, which means that infection is inevitable when resident for sufficient time. The O'Neill Review on antimicrobial resistance estimates that, left unchecked, ten million people will die annually from drug-resistant infections by 2050. Development of biomaterials resistant to bacterial colonization can play an important role in reducing device-associated infections. However, rational design of new biomaterials is hindered by the lack of quantitative structure-activity relationships (QSARs). Here, the development of a predictive QSAR is reported for bacterial biofilm formation on a range of polymers, using calculated molecular descriptors of monomer units to discover and exemplify novel, biofilm-resistant (meth-)acrylate-based polymers. These predictions are validated successfully by the synthesis of new monomers which are polymerized to create coatings found to be resistant to biofilm formation by six different bacterial pathogens: Pseudomonas aeruginosa, Proteus mirabilis, Enterococcus faecalis, Klebsiella pneumoniae, Escherichia coli, and Staphylococcus aureus.

Methodology for the synthesis of methacrylate monomers using designed single mode microwave applicators

A novel single-well prototype high throughput microwave reactor geometry has been produced and shown to be capable of synthesizing an array of non-commercially available methacrylate monomers.

Wet steam measurement techniques

In recent years a greater need for power station efficiency has become evident; improving turbine blade efficiency is one of the methods proposed. This efficiency depends upon the wetness of the steam that comes into contact with the blades of the low-pressure turbine stage in general and all turbines in nuclear power generation. Therefore, measurement of the moisture content of the steam in real time in conjunction with an accurate measure of steam velocity can give an overall mass flow re-entering the turbine, allowing for a feedback control. The system can rely on one technique that can measure suspended droplets and wall-bound liquid film, or a combination of techniques can operate together. This work gives a comprehensive review of the different techniques used to measure the moisture content including the liquid film and moisture content and techniques that can give measurements on both simultaneously. Each technique has its strengths and weaknesses, and they were analysed to see which technique works best overall and which techniques can be used together.

Selective molecular annealing: in situ small angle X-ray scattering study of microwave-assisted annealing of block copolymers

A new experimental set-up facilitating in situ SAXS during microwave annealing of polymers.

Molecular Differentiated Initiator Reactivity in the Synthesis of Poly(caprolactone)-Based Hydrophobic Homopolymer and Amphiphilic Core Corona Star Polymers

Macromolecules that possess three-dimensional, branched molecular structures are of great interest because they exhibit significantly differentiated application performance compared to conventional linear (straight chain) polymers. This paper reports the synthesis of 3- and 4-arm star branched polymers via ring opening polymerisation (ROP) utilising multi-functional hydroxyl initiators and Sn(Oct)2 as precatalyst. The structures produced include mono-functional hydrophobic and multi-functional amphiphilic core corona stars. The characteristics of the synthetic process were shown to be principally dependent upon the physical/dielectric properties of the initiators used. ROP's using initiators that were more available to become directly involved with the Sn(Oct)₂ in the "in-situ" formation of the true catalytic species were observed to require shorter reaction times. Use of microwave heating (MWH) in homopolymer star synthesis reduced reaction times compared to conventional heating (CH) equivalents, this was attributed to an increased rate of "in-situ" catalyst formation. However, in amphiphilic core corona star formation, the MWH polymerisations exhibited slower propagation rates than CH equivalents. This was attributed to macro-structuring within the reaction medium, which reduced the potential for reaction. It was concluded that CH experiments were less affected by this macro-structuring because it was disrupted by the thermal currents/gradients caused by the conductive/convective heating mechanisms. These gradients are much reduced/absent with MWH because it selectively heats specific species simultaneously throughout the entire volume of the reaction medium. These partitioning problems were overcome by introducing additional quantities of the species that had been determined to selectively heat.

Enhanced ‘in situ’ catalysis via microwave selective heating: catalytic chain transfer polymerisation

The formation of a CCTP active catalyst, which is promoted by adopting microwave heating and an “in situ” synthesis methodology.

Understanding microwave heating effects in single mode type cavities-theory and experiment

This paper explains the phenomena which occur in commercially available laboratory microwave equipment, and highlights several situations where experimental observations are often misinterpreted as a 'microwave effect'. Electromagnetic simulations and heating experiments were used to show the quantitative effects of solvent type, solvent volume, vessel material, vessel internals and stirring rate on the distribution of the electric field, the power density and the rate of heating. The simulations and experiments show how significant temperature gradients can exist within the heated materials, and that very different results can be obtained depending on the method used to measure temperature. The overall energy balance is shown for a number of different solvents, and the interpretation and implications of using the results from commercially available microwave equipment are discussed.