Comparison of the mechanical behaviors of biological tissues subjected to uniaxial tensile testing: pig, calf and ostrich pericardium sutured with Gore-Tex

The purpose of this study was to compare the mechanical behavior of calf pericardium, pig pericardium and ostrich pericardium when subjected to tensile testing. Tensile stress was applied to 108 tissue samples, 36 of each type of tissue, until rupture. Groups of three adjacent strips measuring 12 x 2 cm(2) were cut longitudinally. Each group consisted of an unsutured center sample, or control, and the two contiguous samples, that on the right sutured with Gore-Tex at a 90 degrees angle with respect to the longitudinal axis and that on the left sewn with the same suture material at 45 degrees angle. The sutured samples showed a statistically significant loss of resistance (p<0.001) when compared with the corresponding unsutured tissue. The mean stresses at rupture for sutured ostrich pericardium were 21.81 and 20.81 MPa in the samples sewn at 45 degrees and 90 degrees, respectively, higher than those corresponding to unsutured calf and pig pericardium, 14.0 and 11.49 MPa, respectively, at rupture. The analysis of the stress/strain curve shows a smaller difference between sutured and unsutured ostrich pericardium than those observed in the other two biomaterials. These results demonstrate that, in addition to its greater resistance, ostrich pericardium also presents a less pronounced interaction with the suture material. Its capacity to absorb the shearing stress produced by the suture is greater. This report also confirms that the method of selection using paired samples ensures their homogeneity and makes it possible to predict the behavior of a sample by determining that of the other half of the pair.

Biochemical and mechanical behavior of ostrich pericardium as a new biomaterial

We have performed a comparative analysis of glutaraldehyde-preserved ostrich pericardium, as a novel biomaterial, with bovine pericardium. The biochemical characteristics (histology, water content, amino acid composition, and collagen and elastin contents), mechanical properties, and in vivo calcification in a subcutaneous rat model were examined. Ostrich pericardium is slightly thinner and shows a higher water content (70+/-2% vs. 62+/-2%) than bovine pericardium. Additionally, ostrich pericardium presents 1.6-fold lower elastin content and a lower percentage of collagen in reference to the total protein content (68+/-2% vs. 76+/-2%). However, ostrich pericardium shows better mechanical properties, with higher tensile stress at rupture (32.4+/-7.5 vs. 11.5+/-4.6) than calf pericardium. In vivo calcification studies in a rat subcutaneous model show that ostrich pericardium is significantly less calcified than bovine pericardium (23.95+/-13.30 vs. 100.10+/-37.36 mg/g tissue) after 60 days of implantation. In conclusion, glutaraldehyde-stabilized ostrich pericardium tissue shows better mechanical properties than calf tissue. However, calcium accumulation in implanted ostrich tissue is still too high to consider it a much better alternative to bovine pericardium, and anticalcification treatments should be considered.

Uniaxial and biaxial tensile strength of calf pericardium used in the construction of bioprostheses: biomaterial selection criteria

Using morphological and mechanical criteria and applying a method involving paired samples that is widely employed in epidemiology, we obtained an excellent prediction of the mechanical behavior of the calf pericardium used in the construction of cardiac bioprostheses. The method of selection employed in this study may be a highly useful tool for guaranteeing the mechanical resistance of calf pericardium, with a very low level of error.

Durability of a cardiac valve leaflet made of calf pericardium: fatigue and energy consumption

We studied the mechanical behavior of membranes of calf pericardium, similar to those employed in prosthetic valve leaflets, when subjected to tensile fatigue. The objective was to assess its durability, as a fundamental property of cardiac bioprosthesis, and analyze the energy consumption. For this purpose, the authors built a hydraulic simulator to subject a spherical valve leaflet made of calf pericardium to cyclic stress mimicking cardiac function. A total of 522 assays were performed in 40 samples, subjected to cyclic pressures greater than 6 atm, and 482 subjected to pressures ranging between 2 and 6 atm. The mathematical expression that establishes the relationship between the pressure exerted and the frequency was obtained. If we assume that the function is continuous, this equation provides the range of fatigue tolerated for a given number of cycles. Using the optimal values (the five highest values per series), the expression was found to be y = 9.95x(-0 1214) (R(2) = 0.955), where x represents the frequency in cycles per second and y the pressure in atmospheres. In addition, we established the mathematical relationship between the energy consumed and the frequency, which was a function of the pressure exerted, regardless of the region or zone from which the samples had been obtained. The methods of manual and morphology-based selection employed produced widely dispersed results. When a mechanical criterion was included, the similarity in the energy consumed during fatigue testing markedly improved the correlation, with a coefficient of determination between paired samples of R(2) = 0.7477. A mechanical criterion, such as energy consumption, can help to improve sample selection and produce more consistent results. Finally, we obtained the mathematical expression that relates the energy consumed to the pressure exerted and the number of cycles per second to which the valve leaflet was subjected. This procedure enables us to establish the limit to the energy that a biomaterial can consume over a period of time during which it is subjected to a working pressure and, thus, calculate more precisely its durability.

Assessment of pericardium in cardiac bioprostheses. A review

Cardiac valve bioprostheses are assessed in terms of their present and future clinical utility. The problems concerning durability basically involve early failure due to tears in the valve leaflets and late failure mainly associated with calcification of the biological tissue. New strategies for selection and chemical treatment of the biomaterials employed are analyzed, and the available knowledge regarding their mechanical behavior is reviewed. It is concluded that the durability of these devices, and thus their successful use in the future, depends on the knowledge of the interactions among the different biomaterials of which they are composed, the development of new materials, and the engineering design applied in their construction.

Elastic behaviour of sutured calf pericardium: influence of the suture threads

The purpose of this study was to assess the elastic behaviour of calf pericardium used in the construction of cardiac bioprosthesis valve leaflets, sutured with different types of commercially available sutures: silk, Gore-Tex, Surgilene and nylon. Thirty-two samples (four series of eight samples each) were subjected to tensile strength testing to breakage. The breaking stress (MPa) ranged between 4.89 MPa for samples sutured with Gore-Tex and 5.22 MPa for those sewn with nylon. Three samples from each series were subjected to a stepwise stress test, involving increasing levels of stress followed by return to zero, to define the elastic limit (the cut-off point beyond which strain is no longer reversible). Analysis of the results provided the mathematical functions that govern the elastic behaviour (stress/strain) within the elastic range for each type of sutured sample. The series sutured with Surgilene presented the highest mean value (1.649 MPa). Finally, a statistical study was carried out to determine which series showed the greatest probability of having the least interaction between the thread and the pericardium. Allowing an interval of +/- 10%, Gore-Tex showed the best probability in this respect. However, real fatigue testing is necessary to definitively determine which is the best suture to use.

Comparative study of the mechanical behaviour of a cyanoacrylate and a bioadhesive

We compared the mechanical resistance of 18 samples of calf pericardium bonded with a 100 mm2 overlap, by two types of glues: a cyanoacrylate (Loctite 4011) and a bioadhesive (BioGlue). Comparative tensile testing was also carried out in 40 paired samples, 20 bonded with the cyanoacrylate and 20 unbonded controls. The findings at rupture showed a greater resistance of the calf pericardium glued with cyanoacrylate, with a mean tensile strength of 0.15 MPa vs. 0.04 MPa for the biological glue (p= 0.000). They also demonstrated a loss of resistance of the samples bonded with cyanoacrylate when compared with that of the unbonded other halves of the pairs: 0.20 MPa and 0.27 MPa vs. 19.47 MPa and 24.44 MPa (p < 0.001). The method of selection by means of paired samples made it possible to establish the equations that relate the stress and strain, or deformation, with excellent coefficients of determination (R2). These equations demonstrate the marked elastic behaviour of the bonded samples. Moreover, these findings show the cyanoacrylate to be superior to the biological glue, leading to the examination of the compatibility, inalterability over time and mechanical behaviour of the cyanoacrylate in sutured samples, as well as the study of the anisotropy of the biomaterial when bonded with a bioadhesive.

Hysteresis of a biomaterial: influence of sutures and biological adhesives

We studied the changes in energy consumption of samples of calf pericardium, when joined or not joined by sutures and adhesives, by means of hysteretic cycles. Sixty-four samples were subsequently subjected to tensile stress until rupture. An overlapping suture sewn in the form of a rectangle presented an acceptable mean resistance to rupture of over 10 MPa, although lower than the mean values in an unsutured control series where the mean resistance surpassed 15 MPa. The contribution of an acrylic adhesive to the resistance to rupture was negligible. The sutured samples that were reinforced with adhesives and had not been subjected to hysteretic cycles prior to rupture showed an anisotropic behavior. This behavior appeared to be lost in all the samples that underwent hysteretic cycles. We found an inflection point in the stress/strain curve following the stepwise increase in the load, with a value greater than and proximate to the final load applied. This inflection should be analyzed by means of microscopy. Finally, the mathematical relationship between the energy consumed and the stress applied, the strain or deformation produced and the number of cycles of hysteresis to which the samples were subjected was established as the ultimate objective of this study. The bonding systems provoked a greater consumption of energy, with the greatest consumption corresponding to the first cycle in all the series assayed. An equation relating the energy consumption in a sample to the number of hysteretic cycles to which it was subjected was obtained. Its asymptote on the x-axis indicates the energy consumption for a theoretical number of cycles, making it possible to estimate the durability of the sample.

Mechanical effects of increases in the load applied in uniaxial and biaxial tensile testing: Part I. Calf pericardium

The authors analyzed the mechanical behavior of the calf pericardium employed in the construction of valve leaflets for cardiac bioprostheses. Forty samples of pericardium were subjected to uniaxial tensile testing, 20 as controls and 20 exposed to loads increasing stepwise until rupture, with a return to zero load between each new increment. Another 20 samples were used similarly in biaxial tensile tests involving loads increasing stepwise until rupture, again returning to zero load between steps. The ultimate stresses in the uniaxial study were very similar and were not influenced by the region of pericardial tissue being tested or the increments in load to which the tissue was exposed. The mean stresses at rupture in the stepwise biaxial assays were significantly greater (p<0.01). Using morphological and mechanical criteria for sample selection, it was possible to obtain mathematical fits for the stress/strain relationship in both types of assays, with excellent coefficients of determination (R (2)>0.90). In uniaxial tests in which the selection criteria were not applied, the correlation improved as the load increased, a phenomenon that did not occur in the biaxial studies. The values varied throughout the different cycles, adopting exponential forms when the strain was greatest. These variations, which demonstrate that the increase in the energy consumed is a function of the stress applied and of the strain produced, should be good parameters for assessing the changes in the collagen fiber architecture of pericardial tissue subjected to cyclic stress, and may help to detect early failure.

The relationship between stress and relaxation in calf pericardium used in the construction of cardiac bioprostheses

Assessment of relaxation (loss of load within a given time) without apparent deformation is a necessary step before durability assay of biomaterials. From results obtained using calf pericardium, the following conclusions were drawn: (a) there is no limit to relaxation for this biomaterials; (b) the lesser the load applied, the greater the relaxation; and (c) the relaxation curve follows the logarithmic function y = K1 - K2 - Int. These findings demonstrate the poor behaviour of the biomaterial at supposedly low loads and suggest that rupture-point load is not a reliable reference to determine the safety coefficient of calf pericardium used in cardiac bioprostheses.

Mechanical effects of increases in the load applied in uniaxial and biaxial tensile testing. Part II. Porcine pericardium

The mechanical behavior of porcine pericardium was analyzed to compare it with that of calf pericardium employed in valve leaflets for cardiac bioprostheses. Forty samples of pericardium were subjected to uniaxial tensile testing, 20 as controls and 20 exposed to loads increasing stepwise from 0.5 to 1.5 kg and to 3 kg, and thereafter to rupture, with a return to zero load between each new increment. Another 20 samples were used in biaxial tensile tests involving the application of loads increasing stepwise (to 0.5, 1.5, 3 and 5 kg) until rupture with a zero-load interval before each increment. The ultimate stresses were very similar, showing no statistically significant differences when compared in terms of type of assay, controls and study samples or region of pericardial tissue being tested. In the stepwise biaxial assays, the mean stresses at rupture were also very homogeneous. Using morphological and mechanical criteria for sample selection, it was possible to obtain mathematical fits for the stress/strain relationship, with excellent coefficients of determination. The relationship between the area under the stress/strain curve and the load applied or the strain observed was also studied in the biaxial assay as an equivalent to the cycles of hysteresis produced in the test. The increment in the area under the curve (the energy consumed) may be a good parameter for assessing the changes in the collagen fiber architecture of the pericardial tissue, changes that may help to detect early failure.

Influence of the selection of the suture material on the mechanical behavior of a biomaterial to be employed in the construction of implants. Part 2: Porcine pericardium

Using a hydraulic stress simulator, the mechanical behavior of the porcine pericardium used in the construction of cardiac valve leaflets was characterized following the same procedure employed with calf pericardium in Part 1 of this study. One hundred fifty pairs of tissue samples were subjected to tensile testing to rupture. One of the two samples from each of 120 pairs (four series of 30 pairs each) was saturated with commercially available threads made of nylon, silk, Prolene or Gore-Tex, while the other sample in each of these pairs was left unsewn. The remaining 30 pairs were employed as controls in which neither of the two samples was subjected to suturing. The sutured tissue samples showed a significant decrease in tensile strength at rupture (range: 11.61 to 21.22 MPa) when compared with unsutured samples (range: 50.80 to 89.45 MPa; p < 0.01). When these results were compared with their equivalent in calf pericardium, no significant differences were observed (the mean values at rupture in calf pericardium ranged between 211.61 MPa and 26.04 MPa). Again, the application of morphological and mechanical selection criteria to ensure the homogeneity of the samples provided excellent fit with respect to the stress/strain curves. The interaction of the different suture materials with the pericardial tissue was also assessed by comparing the mechanical behavior of the sutured samples with that of the control samples. At the working stress of a cardiac valve leaflet, 0.250 MPa, samples sewn with Gore-Tex were found to show the least difference in behavior with respect to the controls, indicating that this material presented the lowest degree of interaction with the pericardium. In conclusion, the suture clearly has deleterious effects on the resistance of both calf and porcine pericardium, which showed no statistically significant differences in terms of resistance to rupture when their respective sutured or unsutured samples were compared, except in the case of porcine pericardium sewn with silk, which presented lower resistance to rupture in all the zones studied. These findings suggest that the hypothesis that porcine pericardium is less resistant is erroneous. The Gore-Tex suture also presented a lower degree of interaction with the porcine pericardium, with values similar to the working stress of a cardiac valve leaflet. This methodology and the results should be evaluated in dynamic studies, such as fatigue testing, that not only confirm the resistance of the material but establish the durability of the samples being assayed.

Mechanical behavior of chemically treated ostrich pericardium subjected to uniaxial tensile testing: influence of the suture

The mechanical behavior of sutured ostrich pericardium was studied by uniaxial tensile testing. One hundred forty-four tissue specimens were assessed: 96 sutured samples (48 in which a centrally located suture was placed at an angle of 90 degrees with respect to the longitudinal axis, whereas in the remaining 48, a centrally located suture was placed at a 45 degrees angle to the longitudinal axis, in sets of 12 samples each, sewn with sutures made of Gore-Tex, nylon, Prolene, or silk), and 48 unsutured controls. Each group of 24 samples sewn at one angle or the other with the different suture materials was assayed together with a corresponding control group of 12 unsutured samples. The mean tensile strengths in the unsutured controls ranged between 30.16 MPa and 43.42 MPa, whereas those of the sutured sets ranged from 14.68 MPa to 21.91 MPa. The latter presented a statistically significant loss of resistance (p < 0.01) when compared with the unsutured tissue samples. The angle of the suture with respect to the longitudinal axis influenced the degree of shear stress produced by the suture, as well as the behavior of the different suture materials used. The set of samples sewn with Prolene appeared to be that most sensitive to changes in the angle of the suture, whereas tissue sewn at a 45 degrees angle with Gore-Tex presented lower shear stress values in comparison with samples in which the other three materials were used. A method of tissue selection based on morphological and mechanical criteria was used to ensure the homogeneity of the results in such a way that the coefficients of determination (R2) for the stress/strain curve fitting equation ranged between 0.888 and 0.995. This excellent fit made it possible, applying regression analysis, to predict the mechanical behavior of a specimen by determining that of a contiguous tissue sample. Thus, it should be possible, at least theoretically, to characterize the behavior of a specific region or zone of the biomaterial. In conclusion, ostrich pericardium exhibits strong resistance to rupture, even when sutured. The selection method used ensures the homogeneity of the samples and, thus, of the results. The angle of the suture with respect to the longitudinal axis, where the load is centered, determines the shear stress produced by the suture and the mechanical behavior of each suture material.

Energy consumption as a predictor test of the durability of a biological tissue employed in cardiac bioprosthesis

The mechanical behavior of the young bull pericardium in a fatigue test has been studied. This material is a similar tissue to those used in valve leaflet construction for a cardiac bioprosthesis. The consumed energy on each test was evaluated and afterwards used as a predictor of the biomaterial strength. Two-hundred and nine samples were tested to cyclical fatigue. The cut-off point to determine the sample quality was whether or not they resisted at least 4500 cycles. Only 22 samples withstood over that point (10.52%). The samples were classified according to their fatigue behavior in excellent, undefined and unsuitable. By using as a reference the consumed energy in the first 25 cycles, we could distinguish correctly (between 93.2 and 96.1%) the unsuitable material and most of the excellent (between 78.1 and 95.2%). From the rejected material 77% was really detachable and from the accepted, only 50% was excellent, with an equal methodology. The receiver operating characteristics curve was employed to establish decision levels when selecting samples, being 0.85 the best area (theoretical maximum value of 1). It is concluded that the energy wasted is a good predictor of the strength of the tissue. More than 90% of the unsuitable material and 50% of the excellent material (5% of all the material) is detected with this method.

The telescoping suture--Part II: A novel method to improve the mechanical behavior of a new biomaterial: ostrich pericardium

Ostrich pericardium, sutured using a telescoping or overlapping technique, was studied to determine its mechanical behavior. From each of 12 pericardial sacs, four contiguous strips were cut longitudinally, from root to apex, and another four contiguous strips were cut in transverse direction. One of the strips in each set of four was used as an unsutured control and the remaining three were sutured by overlapping 0.5 cm of the tissue and sewing with Gore-tex, Prolene or Pronova. These 96 samples were then subjected to tensile testing along their major axes until rupture. The tensile stresses recorded in the suture materials at the moment tears appeared in the pericardium ranged between 55.99 MPa and 70.23 MPa for Gore-tex in samples cut in the two directions. Shear stress became ostensible at 56 MPa, with clearly evident tears. However, microfracture of the collagen fibers must be produced at much lower stress levels. The comparison of the resistance in kilograms (machine-imposed), without taking into account the sections in which the load was applied, demonstrated only a slight loss of load when the telescoping suture was employed in ostrich pericardium samples. Ostrich pericardium may continue to be an alternative biological material for the construction of heart valve leaflets.

Influence of the selection of the suture material on the mechanical behavior of a biomaterial to be employed in the construction of implants. Part 1: Calf pericardium

A hydraulic stress simulator was employed to study the mechanical behavior of the calf pericardium used in the construction of cardiac valve leaflets. One hundred eighty pairs of tissue samples were subjected to tensile testing to rupture. One of the two samples from each of 144 pairs (four series of 36 pairs each) was sutured with commercially available threads made of nylon, silk, Prolene or Gore-Tex, while the other sample in each of these pairs was left unsewn. The remaining 36 pairs were employed as controls in which neither of the two samples was subjected to suturing. The sutured tissue samples showed a significant decrease in tensile strength at rupture (range: 11.81 to 26.04 MPa) when compared with unsutured samples (range: 39.38 to 87.96 MPa; p < 0.01). The application of morphological and mechanical selection criteria to maximize the homogeneity of the samples provided excellent fit with respect to the stress/strain curves. This method made it possible to carry out a predictive study of the mechanical behavior of a sutured sample, based on that observed in the corresponding unsutured fragment. The interaction of the different suture materials with the pericardial tissue was also assessed by comparing the mechanical behavior of the sutured samples with that of the control samples. At stresses of less than 0.8 MPa, samples sewn with Gore-Tex were found to show the least difference with respect to the controls, indicating that this material presented the lowest degree of interaction with the pericardium. In conclusion, the degree of the loss of resistance to tearing of the sutured samples is of no value in the selection of the optimal suture material. The selection process applied makes it possible to predict the mechanical behavior in response to suturing of a given unsewn tissue specimen by determining that of its sutured mate. The similarity between the findings in samples sewn with Gore-Tex and in the unsutured controls indicates a lesser degree of interaction between the suture material and the pericardium employed in the construction of cardiac valve leaflets.

The influence of chemical treatment and suture on the elastic behavior of calf pericardium utilized in the construction of cardiac bioprostheses

Poor mechanical properties of biological tissue are known to cause wear, leading to the failure of cardiac bioprostheses made of calf pericardium. Different chemical agents such as sodium dodecyl sulfate (SDS) are presently being tested as possible inhibitors of the calcification process. The objective of this report was to determine the mechanical behavior of calf pericardium treated with SDS for 24 h and the influence of the suture on the mechanical properties of the tissue. Forty-eight samples were tested: 24 subjected to a standard treatment with glutaraldehyde (12 sewn with 4/0 silk suture thread) and 24 incubated with SDS for 24 h (12 sewn with the same suture thread). Each sutured and nonsutured sample was cut into two strips to yield paired samples. All were subjected to tensile stress to breaking point. The mean stress at breaking point in the nonsutured series treated with glutaraldehyde alone was 16.42 and 13.85 MPa, depending on the region of the pericardium, while in the sutured samples subjected to glutaraldehyde the mean stress was 7.50 and 7.63 MPa, respectively, differences which were statistically significant (p=0.03 and p=0.003, respectively) when the means for nonsutured samples from equivalent regions treated with glutaraldehyde were compared. The stress at breaking point was lower in the SDS-treated series, ranging between 2.60 and 3.56 MPa. The mathematical functions that govern the stress/strain or deformation were obtained. In the series of pericardium treated with SDS, deformations of 10% were produced with stresses of under 0.4 MPa, an outcome that is intolerable from the constructive point of view. We established a regression model that enabled us to determine the mechanical behavior of a sutured sample by testing a contiguous piece of tissue, with a high correlation coefficient (r\gt 0.99). We consider this finding to be of interest in the selection of pericardium for use in the construction of leaflets for cardiac bioprostheses.

The influence of chemical treatment and suture on the elastic behavior of calf pericardium utilized in the construction of cardiac bioprostheses

Poor mechanical properties of biological tissue are known to cause wear, leading to the failure of cardiac bioprostheses made of calf pericardium. Different chemical agents such as sodium dodecyl sulfate (SDS) are presently being tested as possible inhibitors of the calcification process. The objective of this report was to determine the mechanical behavior of calf pericardium treated with SDS for 24 h and the influence of the suture on the mechanical properties of the tissue. Forty-eight samples were tested: 24 subjected to a standard treatment with glutaraldehyde (12 sewn with 4/0 silk suture thread) and 24 incubated with SDS for 24 h (12 sewn with the same suture thread). Each sutured and non-sutured sample was cut into two strips to yield paired samples. All were subjected to tensile stress to breaking point. The mean stress at breaking point in the non-sutured series treated with glutaraldehyde alone was 16.42 and 13.85 MPa depending on the region of the pericardium, while in the sutured samples subjected to glutaraldehyde the mean stress was 7.50 and 7.63 MPa, respectively, differences which were statistically significant (p = 0.03 and p = 0.003, respectively) when the means for non-sutured samples from equivalent regions treated with glutaraldehyde were compared. The stress at breaking point was lower in the SDS-treated series, ranging between 2.60 and 3.56 MPa. The mathematical functions that govern the stress/strain or deformation were obtained. In the series of pericardium treated with SDS, deformations of 10% were produced with stresses of under 0.4 MPa, an outcome that is intolerable from the constructive point of view. We established a regression model that enabled us to determine the mechanical behavior of a sutured sample by testing a contiguous piece of tissue, with a high correlation coefficient (r \gt 0.99). We consider this finding to be of interest in the selection of pericardium for use in the construction of leaflets for cardiac bioprostheses.

The telescoping suture--Part 1: Does this technique improve the mechanical behavior of a biomaterial?: Calf pericardium

The authors study the mechanical behavior of calf pericardium employed in the construction of cardiac valve leaflets when subjected to telescoping suture, followed by tensile stress until rupture. One hundred twenty pericardial tissue samples were employed, 60 cut from root-to-apex and another 60 cut in transverse direction. Each of these two groups consisted of 12 control samples that were left unsutured and four sets of 12 samples each that were rejoined by telescoping suture using silk, Prolene, nylon or Gore-Tex., and subjected to tensile stress. At the rupture of the sutured tissues, the tensile stress of the suture materials ranged between 57.54 MPa for the series sewn lengthwise with Gore-tex and 114.08 MPa for the series sewn crosswise with silk. At these levels of stress, the deformation of the suture thread was much less marked than that of the calf pericardium, and internal stresses were produced that were difficult for the biomaterial to absorb. There was a loss of real load in all the sutured series when the observed resistance to rupture, expressed in kilograms, was compared with the estimated value. This loss of resistance did not invalidate the telescoping suture technique since the resistance to rupture was still much greater than that associated with suturing the two edges of the cut pericardium together. This report confirms the deleterious role of the shear force generated in the pericardium by the suture.

Resistance to Tensile Stress of a Bioadhesive Utilized for Medical Purposes: Loctite 4011

Sutures are the materials presently employed to secure and give shape to the valve leaflets of cardiac bioprostheses. Their high resistance and low degree of elasticity in comparison with the calf pericardium of which the leaflets are made generates internal stresses that contribute to the failure of the bioprostheses.

Biological adhesives are bonding materials that have begun to be utilized in surgery, although there is a lack of experience in their use with inert tissues or bioprostheses.

We report our study of Loctite 4011, a biological glue composed of a cyano-acrylate that has been employed for medical purposes, in which samples of pericardium bonded with this adhesive were subjected to uniaxial tensile stress. The samples were glued in such a way as to leave an overlap of 1 cm2 between the surfaces of the tissue. The series included 83 samples: 12 tested 24 h after bonding, 17 after 45 days, 17 after 90 days, 19 after 106 days and 18 after 152 days. The samples subjected to deferred trials were preserved using three types of chemical substances: glutaraldehyde, glycerol or saline plus antibiotics. The mean resistance to rupture of the series tested 24 h after gluing was 0.15 MPa (1.47 machine kg). This resistance remained nearly unchanged, regardless of the preservation solution employed, for at least 152 days, the time at which the study ended. The stress strain curves demonstrated a high degree of elasticity throughout the 152 days, a finding that was not influenced by the preservation solution.

This adhesive showed a considerable resistance to tensile stress, although probably insufficient to replace sutures. However, it maintained a surprisingly high degree of elasticity in the samples. Perhaps the time has come to combine these two elements, sutures and adhesives, to improve the elasticity of the structure without a loss of resistance, and increase the durability of bioprostheses.

[Tuberculosis in 1991. A hospital based study]

A retrospective clinical, epidemiological study was carried out with the 53 cases of tuberculosis diagnosed in our center during 1991. The incidence rate was 4.4 per 1,000 clinical histories. Fifteen patients (28.3%) were HIV+, and five were marginalized illegal immigrants (9.4%). Seventy-three percent of the HIV+ patients and 42% of the HIV- patients presented extrapulmonary involvement. In-hospital mortality was 20% in HIV+ patients and 2.6% among the remainder.