Mucoadhesive Delivery Systems. II. Formulation and In‐Vitro/In‐Vivo Evaluation of Buccal Mucoadhesive Tablets Containing Water‐Soluble Drugs

From the previous work (Part I), mucoadhesive formulae containing 5% CP/65% HPMC/30% lactose and 2% PC/68% HPMC/30% mannitol as well as formulae based on sodium carboxymethyl cellulose (SCMC) were selected. Medicated tablets were prepared using diltiazem hydrochloride (DZ) and metclopramide hydrochloride (MP) in two different doses (30 and 60 mg). The effect of drug and dose on the mucoadhesive properties and in-vitro drug release was evaluated. All formulae produced extended drug release (over 8 to 12 h). Polyacrylic acid based matrices (PAA) showed Fickian's diffusion release pattern for both drugs. SCMC ensured zero-order release for DZ, which deviated to anomalous behavior in case of MP. Doubling the dose significantly reduced the bioadhesion strength (p<0.05) with a slight improvement in drug release rate. The formulation of bilayer tablets containing drug-free layer and medicated layer enhanced the drug release without affecting the bioadhesive performance. The bilayer tablet formulated with 2% PC/68% HPMC/30% mannitol (PC2) was selected for studying the in-vivo metoclopramide release in four healthy volunteers. The tablet ensured controlled drug release for 12 h, in addition, good correlation (r=0.9398) was observed between in-vitro and in-vivo data. The effect of ageing on selected formulae containing DZ and MP, respectively, was studied. Storage at 40 degrees C and 75% relative humidity for 6 months didn't influence the mucoadhesive performance, however, an enhanced released rate was observed.

Mucoadhesive Delivery Systems. I. Evaluation of Mucoadhesive Polymers for Buccal Tablet Formulation

Different types of mucoadhesive polymers, intended for buccal tablet formulation, were investigated for their comparative mucoadhesive force, swelling behavior, residence time and surface pH. The selected polymers were carbopols (CP934, and CP940), polycarbophil (PC), sodium carboxymethyl cellulose (SCMC) and pectin representing the anionic type, while chitosan (Ch) as cationic polymer and hydroxypropylmethyl cellulose (HPMC) as a non-ionic polymer. Results revealed that polyacrylic acid derivatives (PAA) showed the highest bioadhesion force, prolonged residence time and high surface acidity. SCMC and chitosan ensured promising bioadhesive characteristics, whilst HPMC and pectin exhibited weaker bioadhesion. Different polymer combinations as well as formulations were evaluated to improve the mucoadhesive performance of the tablets. Bioadhesive tablet formulations containing either 5% CP934, 65% HPMC and 30% spray-dried lactose or 2% PC, 68% HPMC and 30% mannitol showed optimum mucoadhesion and suitable residence time. SCMC, when formulated individually, exhibited promising bioadhesion, acceptable swelling, convenient residence time and surface pH. In-vivo trials of these formulations proved non-irritative and prolonged residence of the mucoadhesive tablets on human buccal mucosa for 8 to 13 h.

Design and characterization of mucoadhesive buccal patches containing cetylpyridinium chloride

Mucoadhesive patches for delivery of cetylpyridinium chloride (CPC) were prepared using polyvinyl alcohol (PVA), hydroxyethyl cellulose (HEC) and chitosan. Swelling and bioadhesive characteristics were determined for both plain and medicated patches. The results showed a remarkable increase in radial swelling (S(D)) after addition of the water-soluble drug (CPC) to the plain formulae. A decrease in the residence time was observed for PVA and chitosan-containing formulae. Higher drug release was obtained from PVA patches compared to HEC ones, while both are non-ionic polymers. A considerable drop in release was observed for chitosan formulae after the addition of water-soluble additives, polyvinyl pyrrolidone (PVP) and gelatin. Ageing was done on PVA formulae; the results showed there was no influence on the chemical stability of CPC, as reflected from the drug content data. Physical characteristics of the studied patches showed an increase in the residence time with storage accompanied with a decrease in drug release. This may be due to changes in the crystal habit of the drug as well as to slight agglomeration of the polymer particles.

Potential improvement in the shelf life of parenterals using the prodrug approach: bacampicillin and talampicillin hydrolysis kinetics and utilization time

The utilization time for a parenteral prodrug solution with a bioavailable fraction of unity was defined as the time during which the total of the prodrug concentration and the drug concentration equals or exceeds 90% of the initial prodrug concentration. This utilization time was calculated as a function of pH, buffer, and temperature using the experimentally determined rate expressions for bacampicillin and talampicillin. The results were compared to the shelf life of ampicillin solutions under identical storage conditions. First-order rate constants were determined for conversion of the prodrugs to ampicillin (kc), for beta-lactam degradation of the prodrugs (knc), for the overall loss of prodrugs (ksum), and for beta-lactam degradation of ampicillin (kh) in aqueous solutions at 25.0 to 60.0 degrees C, mu = 0.5, in the pH range 0.90 to 8.4. Loss of bacampicillin proceeded primarily by degradation at pH levels below 4 but was due predominantly to conversion at pH levels above 5. Loss of talampicillin was due primarily to conversion throughout the entire pH range. While the prodrug utilization times were approximately twice the shelf life of ampicillin in acidic solutions, ampicillin was significantly better in neutral solutions. The results illustrate the potential for increased prodrug storage periods when utilization time is defined on the basis of the bioactivity rather than on the prodrug concentration alone.

Physicochemical study of drug binary systems. Part 3: Tolbutamide-urea and tolbutamide-mannitol systems

The phase diagram of the tolbutamide-urea system, constructed by data obtained from the microheating table apparatus, was a peritectic type. It showed the possibility of the formation of two molecular compounds with incongruent m. p. at 112 degrees C and 123 degrees C. Metastable and stable eutectic points were observed at 63 degrees C and 92 degrees C respectively. The phase diagram of tolbutamide-mannitol system revealed that in addition to eutectic liquefaction at 102 degrees C and 6% (w/w) mannitol, there was a region [40--80% (w/w) mannitol] in which the two components were not completely miscible in the liquid state. Solubility studies showed an increase of about 2.5 fold in the solubility of tolbutamide with 0.5 g% urea and suggested the possibility of the formation of a low-solubility complex in addition to a soluble higher complex of the two components. No obvious increase in the solubility of tolbutamide was detected in the presence of mannitol. A full description of the nature and composition of the final solidified melts of the two present systems could prove to be helpful in the explanation of the dissolution behaviour of the different studied samples and their corresponding physical mixtures. The fused 90% urea and mannitol solid dispersions showed a fast rate of dissolution in the order of 15 and 10 times (respectively) greater than pure tolbutamide.