The Influence of Diatomite Addition on the Properties of Geopolymers Based on Fly Ash and Metakaolin

Geopolymer materials, considered to be an alternative to Portland cement-based concretes, can be produced from various types of waste aluminosilicate raw materials. This article presents the results of research related to the use of diatomite as an additive in geopolymers. The results of testing geopolymer composites with 1%, 3%, and 5% additions of diatomite with a grain size of 0-0.063 mm after and without thermal treatment were presented. This article presents the physical properties of the diatomite additive, the morphology of diatomite particles SEMs, thermal analysis, and compressive strength test results. In this research, diatomite was treated as a substitute for both fly ash and metakaolin (replaced in amounts of 1 and 3%) and as a substitute for sand introduced as a filler (in this case, 5% of diatomite was added). As a result of this research, it was found that the addition of diatomite instead of the main geopolymerization precursors in amounts of 1 and 3% had a negative impact on the strength properties of geopolymers, as the compressive strength was reduced by up to 28%. The introduction of crushed diatomite instead of sand in an amount of 5% contributed to an increase in strength of up to 24%.

Silver Nanoparticles for Waste Water Management

Rapidly increasing industrialisation has human needs, but the consequences have added to the environmental harm. The pollution caused by several industries, including the dye industries, generates a large volume of wastewater containing dyes and hazardous chemicals that drains industrial effluents. The growing demand for readily available water, as well as the problem of polluted organic waste in reservoirs and streams, is a critical challenge for proper and sustainable development. Remediation has resulted in the need for an appropriate alternative to clear up the implications. Nanotechnology is an efficient and effective path to improve wastewater treatment/remediation. The effective surface properties and chemical activity of nanoparticles give them a better chance to remove or degrade the dye material from wastewater treatment. AgNPs (silver nanoparticles) are an efficient nanoparticle for the treatment of dye effluent that have been explored in many studies. The antimicrobial activity of AgNPs against several pathogens is well-recognised in the health and agriculture sectors. This review article summarises the applications of nanosilver-based particles in the dye removal/degradation process, effective water management strategies, and the field of agriculture.

Influence of Alkaline Earth Metals on Structure Formation and Magnesium Alloy Properties

The main aim of this work is to improve the structure and properties of the magnesium alloy ML5 by modifying it with alkaline earth metals (ALM). The separate and joint influence of calcium and barium on the macrostructure and microstructure of the alloy of Mg-Al-Zn system was investigated. The qualitative and quantitative estimation of the structural components was carried out. Alkali earth metals were included in complex intermetallic phases and serve as additional crystallization centers. Modification of magnesium alloys with alkaline earth metals is established in an amount of 0.05 to 0.1 wt. % increased the bulk percentage of intermetallic phases by ~1.5 times, shifting them towards smaller size groups while simultaneously forming spherical intermetallic phases located in the grain centre and serving as additional crystallization centers. In this case, grain size reduction and significant refinement of the alloy structural components were provided. The dependency of the separate and joint influence of alkali earth metals on the castings complex of properties of the magnesium alloy has been established. Thus, a separate modification of the ML5 alloy provided the maximum level of its strength and ductility with the addition of 0.1% Ca or Ba. The modification of the complex (0.1% Ca + 0.1% Ba) of the magnesium alloy decreased the dimensions of its structural components 1.5 times and increased the strength of the alloy by 20%, the ductility by 2 times and the long-term heat resistance 1.5 times due to the formation of the intermetallic phases of the complex composition. Linear dependences were obtained that describe the influence of the characteristics of the structural components of the modified magnesium alloy on its mechanical properties. The developed technology for modifying cast magnesium alloys with alkaline earth elements provides an improvement in casting quality and allows the reliability and durability of responsible casting operation.

Prediction of Abrasive Waterjet Machining Parameters of Military-Grade Armor Steel by Semi-Empirical and Regression Models

Rolled homogeneous armor steel (RHA) with a high tensile strength, toughness, and hardness is often used in military combat vehicles. RHA is a high-strength low alloy steel suitable for all battlefield usage in military vehicles. The present work examines the prediction output responses in the material removal rate (MRR), surface roughness (Ra), and kerf angle (Ka) for the AWJM of armor steel using regression and semi-empirical models. The AWJM trials were performed using an L27 factorial design with each process variable set to three levels, namely, the standoff distance (SOD), jet traversing speed (JT), and jet water pressure (P). A regression model was constructed using the response surface method (RSM) and data from the trials. Through dimensional analysis and with Buckingham’s π-theorem, a semi-empirical model was built using both the experimental data and material property data. Predictions made by the models were proportionate with the results of the experiments under the same conditions. Microscopic investigations on MRR and Ra were performed using a scanning electron microscope (SEM). The optimal values of the output responses of the machined armor steel plate were obtained with higher MRR = 298.92 mm³/min, lower Ka = 0.651°, and lower Ra = 2.23 µm. The present work established that semi-empirical models accurately predict the output responses in the AWJM of armor steel.

Impact of injection rate on the Thrombolysis in Myocardial Infarction (TIMI) trial frame count

A mechanical injection was used to determine the impact of injection rate on the TIMI frame count. The 1.0-ml/s increase in hand injection rates from the 10th to 90th percentiles for angiographers is associated with a minor decrease of <2 frames that is <7% of the corrected TIMI frame count.

Coronary artery injection technique: a quantitative in vivo investigation using modern catheters

To date, there have been no quantitative in vivo assessments of contrast volumes and injection rates using modern high flow catheters during coronary angiography. Contrast volumes (n = 554), injection durations (n = 563), and injection rates (n = 498) were collected during 88 cardiac catheterizations. With increasing cathetersize (6, 7, and 8 French), injection volume increased (P < 0.0001), duration decreased (P < 0.0001), and rate increased (P < 0.0001). Compared with injections into the right coronary artery, left coronary artery injections were larger (7.1 +/- 0.1 cc vs. 4.8 +/- 0.1 cc, p < 0.0001), longer (3.6 +/- 0.05 sec vs 3.0 +/- 0.07 sec, P < 0.0001) and faster (2.1 +/- 0.04 cc/sec vs. 1.7 +/- 0.06 cc/sec, P < 0.0001). Patients with a significant stenosis in the left main or proximal right coronary artery received less contrast (P < 0.0001) more slowly (P < 0.0001) over a similar duration of injection (P = NS). When collaterals arose from the injected artery, angiographers injected more contrast (P < 0.001) over a longer period (P < 0.0001) more slowly (P < 0.0001). Catheter size and the injected vessel's location and anatomy significantly affect coronary catheterization injection technique.