Aptamer-based array electrodes for quantitative interferon-γ detection

Present work describes the methylene blue tagged thiolated aptamer-modified gold micro-array based biosensor for specific detection of IFN-γ. The microchips with the microelectrode array were fabricated using standard silicon microfabrication technologies, and modified with methylene blue tagged aptamer using standard gold thiol chemistry. Electrodes were characterized and tested using Cyclic Voltammetric (CV) and Square Wave Voltammetry (SQW) measurements in a standard three-electrode format at room temperature. On an aptamer modified electrode, aptamer density was estimated to be about 4.4 × 10(12)molecules/cm(2). In IFN-γ studies, oxidation peak currents were found to decrease and more than 50% signal suppression was achieved at 500 ng/ml. Further, the magnitude of signal suppression was found to be logarithmically proportional to the IFN-γ in the concentration range of 1-500 ng/ml, with a detection limit of 1.3 ng/ml (i.e. 0.8 fmol in used sample volume of 10 µl). Biosensor showed negligible signal changes (5%) in a very high non-specific protein background, while still able to differentiate target protein IFN-γ at 5 ng/ml. The results indicated that our sensor binds selectively to target molecules, and the non-specific binding where adsorption of BSA protein molecules may be effectively omitted from consideration.

Electrokinetic Analysis of Cell Translocation in Low-Cost Microfluidic Cytometry for Tumor Cell Detection and Enumeration

Conventional Coulter counters have been introduced as an important tool in biological cell assays since several decades ago. Recently, the emerging portable Coulter counter has demonstrated its merits in point of care diagnostics, such as on chip detection and enumeration of circulating tumor cells (CTC). The working principle is based on the cell translocation time and amplitude of electrical current change that the cell induces. In this paper, we provide an analysis of a Coulter counter that evaluates the hydrodynamic and electrokinetic properties of polystyrene microparticles in a microfluidic channel. The hydrodynamic force and electrokinetic force are concurrently analyzed to determine the translocation time and the electrical current pulses induced by the particles. Finally, we characterize the chip performance for CTC detection. The experimental results validate the numerical analysis of the microfluidic chip. The presented model can provide critical insight and guidance for developing micro-Coulter counter for point of care prognosis.

Effects of the electrode size and modification protocol on a label-free electrochemical biosensor

In the present work, the effect of a surface modification protocol along with the electrode size has been investigated for developing an efficient, label-free electrochemical biosensing method for diagnosis of traumatic brain injury (TBI) biomarkers. A microdisk electrode array (MDEA) and a macroelectrode with a comb structure (MECS) were modified with an anti-GFAP (GFAP = glial fibrillary acidic protein) antibody using two protocols for optimum and label-free detection of GFAP, a promising acute-phase TBI biomarker. For the MDEA, an array of six microdisks with a 100 μm diameter and, for the MECS, a 3.2 mm × 5.5 mm electrode 5 μm wide with 10 μm spaced comb fingers were modified using an optimized protocol for dithiobis(succinimidyl propionate) (DSP) self-assembled monolayer formation. Anti-GFAP was covalently bound, and the remaining free DSP groups were blocked using ethanolamine (Ea). Sensors were exposed to solutions with different GFAP concentrations, and a label-free electrochemical impedance spectroscopy (EIS) technique was used to determine the concentration. EIS results confirmed that both types of Ea/anti-GFAP/DSP/Au electrodes modified with an optimized DSP-based protocol can accurately detect GFAP in the range of 1 pg mL(-1) to 100 ng mL(-1) with a detection limit of 1 pg mL(-1). However, the cross-use of the MDEA protocol on the MECS and vice versa resulted in very low sensitivity or poor signal resolution, underscoring the importance of proper matching of the electrode size and type and the surface modification protocol.