Ultra-Sensitive Humidity Sensor Based on Optical Properties of Graphene Oxide and Nano-Anatase TiO2

Generally, in a waveguide-based humidity sensors, increasing the relative humidity (RH) causes the cladding refractive index (RI) to increase due to cladding water absorption. However, if graphene oxide (GO) is used, a reverse phenomenon is seen due to a gap increase in graphene layers. In this paper, this interesting property is applied in order to fabricate differential humidity sensor using the difference between RI of reduced GO (rGO) and nano-anatase TiO2 in a chip. First, a new approach is proposed to prepare high quality nano-anatase TiO2 in solution form making the fabrication process simple and straightforward. Then, the resulted solutions (TiO2 and GO) are effortlessly drop casted and reduced on SU8 two channels waveguide and extensively examined against several humid conditions. Investigating the sensitivity and performance (response time) of the device, reveals a great linearity in a wide range of RH (35% to 98%) and a variation of more than 30 dB in transmitted optical power with a response time of only ~0.7 sec. The effect of coating concentration and UV treatment are studied on the performance and repeatability of the sensor and the attributed mechanisms explained. In addition, we report that using the current approach, devices with high sensitivity and very low response time of only 0.3 sec can be fabricated. Also, the proposed device was comprehensively compared with other state of the art proposed sensors in the literature and the results were promising. Since high sensitivity ~0.47dB/%RH and high dynamic performances were demonstrated, this sensor is a proper choice for biomedical applications.

Photo-induced reduction of graphene oxide coating on optical waveguide and consequent optical intermodulation

Increased absorption of transverse-magnetic (TM) - polarised light by a graphene-oxide (GO) coated polymer waveguide has been observed in the presence of transverse-electric (TE) - polarised light. The GO-coated waveguide exhibits very strong photo-absorption of TE-polarised light - and acts as a TM-pass waveguide polariser. The absorbed TE-polarised light causes a significant temperature increase in the GO film and induces thermal reduction of the GO, resulting in an increase in optical-frequency conductivity and consequently increased optical propagation loss. This behaviour in a GO-coated waveguide gives the action of an inverted optical switch/modulator. By varying the incident TE-polarised light power, a maximum modulation efficiency of 72% was measured, with application of an incident optical power level of 57 mW. The GO-coated waveguide was able to respond clearly to modulated TE-polarised light with a pulse duration of as little as 100 μs. In addition, no wavelength dependence was observed in the response of either the modulation (TE-polarised light) or the signal (TM-polarised light).

Nonlinear optical response of platinum nanostructures and application for water detection in transformer oil

We report the fabrication of platinum nanostructures on an ITO substrate (Pt-NSs).

Z-scan studies of the nonlinear optical properties of gold nanoparticles prepared by electron beam deposition

This paper details the fabrication process for placing single-layer gold (Au) nanoparticles on a planar substrate, and investigation of the resulting optical properties that can be exploited for nonlinear optics applications. Preparation of Au nanoparticles on the substrate involved electron beam deposition and subsequent thermal dewetting. The obtained thin films of Au had a variation in thicknesses related to the controllable deposition time during the electron beam deposition process. These samples were then subjected to thermal annealing at 600°C to produce a randomly distributed layer of Au nanoparticles. Observation from field-effect scanning electron microscope (FESEM) images indicated the size of Au nanoparticles ranges from ∼13 to ∼48  nm. Details of the optical properties related to peak absorption of localized surface plasmon resonance (LSPR) of the nanoparticle were revealed by use of UV-Vis spectroscopy. The Z-scan technique was used to measure the nonlinear effects on the fabricated Au nanoparticle layers where it strongly relates LSPR and nonlinear optical properties.

Graphene oxide-based waveguide polariser: from thin film to quasi-bulk

We have demonstrated a broadband waveguide polariser with high extinction ratio on a polymer optical waveguide coated with graphene oxide via the drop-casting method. The highest extinction ratio of nearly 40 dB is measured at 1590 nm, with a variation of 4.5 dB across a wavelength range from 1530 nm to 1630 nm, a ratio that is (to our knowledge) the highest reported for graphene-based waveguide polarisers to date. This result is achieved with a graphene oxide coating length along the propagation direction of only 1.3 mm and a bulk film thickness of 2.0 µm. The underlying principles of the strongly polarisation dependent propagation loss demonstrated have been studied and are attributed to the anisotropic complex dielectric function of graphene oxide bulk film.

Direct period measurement for fiber Bragg grating using an optical imaging technique

This paper proposes an approach based on an optical imaging technique for the period measurement of fiber Bragg gratings (FBG). The simple, direct technique involves a differential interface contrast (DIC) microscope and a high-resolution CCD camera. Image processing is performed on the microscope images to obtain low-noise grating profiles and then the grating periods. Adopting a large image sample size in the image processing can reduce uncertainty. During the investigation, FBGs of different grating periods are fabricated by prestraining the photosensitive fibers during the UV-writing process. A good linearity between the measured Bragg wavelengths and grating periods is observed and the measured strain-optics coefficient was found to be in agreement with reported literature.

Spreading profile of evaporative liquid drops in thin porous layer

Spreading of evaporative liquid drops in a thin porous layer has been studied. The entire spreading process can be divided into three distinct phases according to the change of the wetted porous region size. The first phase is characterized by the expansion of the wetted porous region and shrinking of the liquid drop. Contact line pinning is observed in the wetted porous region in the second phase even with the liquid drop totally absorbed into the porous layer. The third phase sees the shrinkage of the wetted porous region until it is not observable. Based on these observations, a model is devised to simulate the spreading of a liquid drop under the studied conditions. Partial differential equations are used to describe the relation between liquid drop volume and other important parameters of a fluid flow, including maximum wetted region diameter achieved, time taken to reach each spreading process phase, and evaporation rate. Calculated results are in good agreement with the experimental data.

Note: Fabrication of tapered fibre tip using mechanical polishing method

Tapered fibre tips fabricated using mechanical polishing method is studied. The fibre tips are formed by sequential polishing flat-ended single mode fibres with decreasing aluminium oxide polishing film grit size. Based on the proposed technique, tapered fibre tips with cone angle ranging from 30° to 130° are fabricated by controlling the polishing angle. Besides the variety of cone angle, considerable smoothness of the fibre tip surface may assist in good metal coating and hence a well-defined aperture can be obtained. In addition, this paper presents a two-step hybrid fabrication method combining the proposed polishing method with chemical etching method to increase the possible fibre tip cone angles achievable by chemical etching method.