Remineralization ability of different root canal sealers

Aims

This research was designed to contrast the biocompatibility and remineralization ability of different sealers (BioRoot, MTA-FillApex and GuttaFlow-Bioseal).

Method

Twenty rabbits were used in this study, they were randomly divided into 4 groups equally depending on the observation time"3,7,14, and 28 days" post-implantation. Each rabbit was generally anesthetized,"7cm"long incision was made on the skin of the right and left sides of the ventral aspect of the mandible of each rabbit, 4 bony cavities of approximately"5mm"in depth and"2mm"in diameter (2 cavities on the left side and 2 cavities on the right side of mandible of each rabbit) were made in the cortical surface of the buccal alveolar bone. The sealers mixed depend on manufactural instructions and immediately insert into the prepared cavities (in the right side the BioRoot and MTA-FillApex were placed while on the left side, GuttaFlow-Bioseal was placed in one cavity and the other cavity was left unfilled as control).The same volume of each sealer was placed in the corresponding cavity using disposable syringes. After each observation period, the animals were sacrificed and bone biopsy from the tested area was taken and examined histologically using Olympus light microscopy at"400X"magnification.

Results

The obtained data were analyzed through non-parametric statistical tests using SPSS software version"22".Kruskal-Wallis test and Mann - Whitney test were utilized at"0.05"levels of significance to evaluate the results. GuttaFlow-Bioseal displayed excellent biocompatibility in comparison to other groups indicated by low inflammatory tissue reaction at all evaluation intervals. While the BioRoot group represented better osteo-conductivity although statistically not significant than GuttaFlow-Bioseal group.

Conclusion

BioRoot and GuttaFlow-Bioseal showed higher osteo-conductivity and biocompatibility than MTA-FillApex. However, all sealer used in this study were well tolerated by bone tissue and might accelerate bone repair.

Shear-bond strength of different Self-Etching adhesive systems to dentin with or without laser irradiation before photopolymerization (A comparative Study)

This study aimed at comparing shear-bond strength (SBS) of different self-etching adhesive systems (Clearfil S³ Bond Plus, G-Premio BOND and IBond) to dentin without or with diode-laser irradiation before photo-polymerization and to determine the effect of storage and thermo-cycling on SBS of adhesive systems.

METHODS

The buccal surface of 84 extracted maxillary premolars was grounded to create flat surface. The specimens were allocated into 3 groups (n = 28) depending upon the adhesive systems, then each group was divided into two sub-group (I, II) (n = 14). After the placement of respective adhesive systems on the flat surface, adhesive system in group I was photo-polymerized immediately, while in group II, the adhesive systems were exposed to diode-laser before photo-polymerization. Composite cylinder (4 mm in diameter and 2 mm height) was built on the flat surface of each specimen. Then group I and II were divided into two sub-groups (n = 7) according to the storage time and thermo-cycling (1 day without thermo-cycling or 72 days with thermo-cycling) then all the specimens were stored in distilled water. The SBS was measured at the end of storage period. ANOVA, Duncan's Multiple Range Test and independent t-test "P ≤ 0.05" were used for data analysis.

RESULTS

G-premio BOND showed the highest mean value of SBS followed by Clearfil S³ Bond plus without significant difference between them, while IBond revealed the least mean value. Laser irradiation had positive effect on the bond-strength of all tested adhesive systems. The results also showed that the storage with thermo-cycling had negative effect on the bond-strength in groups without laser irradiation for all tested adhesive systems, while for groups with laser irradiation, the reduction in the bond-strength of all tested adhesive systems was not significant.

CONCLUSION

Diode-laser application prior to photo-polymerization of self-etch adhesive systems significantly increased the bond-strength to dentin and can increase the durability of composite adhesion.