Exploring the degradation behavior of MgXAg alloys by in vitro electrochemical methods

Magnesium as biodegradable biomaterial could serve as bone augmentation material in implant dentistry. The knowledge about the predictability of the biodegradation process is essential as this process needs to go hand in hand with the formation of new bone to gradually replace the augmentation material. Therefore, this work aimed to assess if the electrochemistry (EC) measurements of the corrosion process correlate with the surface features at various time points during the surface degradation, in order to describe the degradation process of Mg and Mg alloys more reliably, under the assumption that differences in EC behavior can be detected and related to specific patterns on the surface.

In this test setup, a special optical chamber was used for electrochemical measurements on Mg and Mg-alloys (Mg2Ag, Mg4Ag, and Mg6Ag). Specimens were investigated using different circulating cell culture solutions as electrolytes, these were minimum essential medium (MEM), Hank's Balanced Salt Solution (HBSS), and MEM+ (MEM with added sodium hydrogen carbonate) at 37 °C. Open circuit potential measurements (OCP) over 30 min followed by cyclic polarization were performed. The electrochemistry data, including OCP, exchange current density and corrosion potential, were compared with visible changes at the surface during these treatments over time. The results show that the addition of silver (Ag) leads to a “standardization” of the degradation regardless of the selected test medium. It is currently difficult to correlate the visible microscopic changes with the data taken from the measurements. Therefore, further investigations are necessary.

•

MgXAg alloys were investigated electrochemically in MEM, HBSS and MEM+ at 37℃ in circulated electrolyte.

•

A correlation between optical appearance and electrochemical data was performed.

•

Visible high activity on the surface corresponded with high electrochemical activity.

The influence of MgH2 on the assessment of electrochemical data to predict the degradation rate of Mg and Mg alloys

Mg and Mg alloys are becoming more and more of interest for several applications. In the case of biomaterial applications, a special interest exists due to the fact that a predictable degradation should be given. Various investigations were made to characterize and predict the corrosion behavior in vitro and in vivo. Mostly, the simple oxidation of Mg to Mg²⁺ ions connected with adequate hydrogen development is assumed, and the negative difference effect (NDE) is attributed to various mechanisms and electrochemical results. The aim of this paper is to compare the different views on the corrosion pathway of Mg or Mg alloys and to present a neglected pathway based on thermodynamic data as a guideline for possible reactions combined with experimental observations of a delay of visible hydrogen evolution during cyclic voltammetry. Various reaction pathways are considered and discussed to explain these results, like the stability of the Mg⁺ intermediate state, the stability of MgH₂ and the role of hydrogen overpotential. Finally, the impact of MgH₂ formation is shown as an appropriate base for the prediction of the degradation behavior and calculation of the corrosion rate of Mg and Mg alloys.

n-Butyl cyanoacrylate synthesis. A new quality step using microwaves

Alkyl cyanoacrylates are interesting products for use in industry because of their properties enabling them to stick together a wide range of substrates. n-Butyl cyanoacrylate is one of the most successfully used tissue adhesives in the field of medicine because it exhibits bacteriostatic and haemostatic characteristics, in addition to its adhesive properties. At present, its synthesis is performed with good yields via Knoevenagel condensation using conventional sources of heating, but this requires a long processing time. The aim of this work was to look for a new way of synthesising n-butyl cyanoacrylate using microwave irradiation as the source of heating. This non-conventional source of heating most likely reduces the process time of the synthesis. In comparison with a conventional heating source, such as an oil bath, the results showed the advantages of this method whereby the n-butyl cyanoacrylate gave the same yield and quality with a reduction in the reaction time by a factor of 3-5-fold.

Critical discussion of the results from different corrosion studies of Mg and Mg alloys for biomaterial applications

The aim of this work was to collect and compare data from different published reports which focused on the description of the influence of different electrochemical setups for the assessment of magnesium corrosion. Based on this, a comparison with our own results, obtained for LAE 442 and AZ 31, was made and discussed. As the collection of data has shown, the reported inconsistencies between in vivo and electrochemical data depend greatly on the electrochemical medium used, on the alloy composition and on surface preparation. Nevertheless, these differences also exist when comparing different in vitro results using different methodologies and even different Mg alloys, and need therefore to be discussed more thoroughly in the future. The simulation of transport conditions of the in vivo interface should become a focus of research interest in order to gain a better understanding of the influence of connecting processes on the degradation of the biomaterials.

Electrochemical characterization of cobalt-based alloys using the mini-cell system

OBJECTIVES

The aim of this work was to investigate the electrochemical behavior of cobalt-based alloys of different compositions using the mini-cell system (MCS) and to test the sensitivity of this technique in the detection of variations in the electrochemical behavior caused by the different compositions of cobalt-based alloys.

METHODS

The electrochemical measurements were performed on two cobalt-based alloys, having a small content of gold (Bärlight and Gold Core); one cobalt-platinum-ruthenium alloy (Porta Smart) and one classical Co-based alloy (Wironit), in two different electrolytes, 1% NaCl and phosphate buffered solution (PBS).

RESULTS

Based on I versus E curves, enhanced pitting corrosion capability was observed for the cobalt-based alloys, especially for those with lower chromium content and with the addition of a small amount of gold. The alloying of Co with Pt and Ru (Porta Smart), and the standard Co-based alloy do not show any critical instability; in contrast, a small addition of Au enhanced the pitting corrosion activity and reduced the corrosion stability. For higher alloy stability, a minimum 30% atomic ratio of chromium in the alloy composition is necessary. Furthermore, it was shown that MCS has sensitivity for the qualitative comparison of the alloys as well as in the electrochemical characterization of each alloy.

SIGNIFICANCE

Electrochemical measurements are essential to assess the quality of an alloy. MCS might help in understanding the role the elements play in the electrochemical behavior of the alloys and at the same time contribute to the selection of the alloys in terms of their quality, even before more complex tests in vitro or in vivo are applied, and might reduce the costs for materials research.

Electrochemical characterisation of dental alloys: its possibilities and limitations

Dental alloys are metallic biomaterials which have a broad variation of composition compared to technical alloys. It is therefore in the interest of patients and technicians to conduct a good assessment of the electrochemical behaviour of dental alloys in order to collect information about their corrosion resistance. The purpose of this work was to demonstrate possibilities and limitations of two electrochemical techniques: the voltammetry of immobilised microparticles (ViMP) onto lead, and cyclic voltammetry measurements with the help of the mini-cell system (MCS). Based on fingerprints obtained from ViMP it was possible to analyse and differentiate the dental alloys. The results obtained by MCS were comparable with ViMP, but give a better understanding of the corrosion behaviour of the materials.

Preterm twin gestation and cystic periventricular leucomalacia

OBJECTIVE

To identify risk factors for the development of cystic periventricular leucomalacia (PVL) in twin gestation.

DESIGN

Retrospective case-control study.

SETTING

Tertiary care university hospital, Department of Paediatrics, Division of Neonatology, Graz, Austria.

PATIENTS

Preterm twin gestations with one sibling having developed cystic PVL, diagnosed by ultrasound scans, compared with their co-twins without PVL, in hospital between 1988 and 2000.

MAIN OUTCOME MEASURES

Perinatal and postnatal risk factors for the development of PVL.

RESULTS

Eighteen preterm twin gestations were included. Monochorionicity was evident in 47% of the pregnancies, and twin to twin transfusion syndrome occurred in two cases (11%). Fetal distress correlated inversely with PVL (15% v 53%, p = 0.019, relative risk (RR) = 2.057, 95% confidence interval (CI) = 1.067 to 3.968). Hypocarbia with Pco(2) levels below 30 mm Hg (4 kPa) was diagnosed in 29% of the cases compared with 6% of the controls (p = 0.038, RR = 1.944, 95% CI = 1.113 to 3.396). There were no significant differences between groups with regard to premature rupture of the membranes, early onset infection, respiratory distress syndrome, mechanical ventilation, arterial hypotension, persistent ductus arteriosus, and hyperbilirubinaemia. Asphyxia was only evident in three controls. Three infants died and another three were lost to follow up. None of the cases compared with 62% of the controls were diagnosed as having developed normally (p < 0.001), and 14 cases (82%) compared with two controls (15%) developed cerebral palsy (p < 0.001).

CONCLUSION

Hypocarbia was the only risk factor strongly associated with cystic PVL. The general outcome of the infants was poor.