Synthesis of patterned polyHIPE-hydrogel composite materials using thiol-ene chemistry

Elastomeric materials combining multiple properties within a single composite are highly desired in applications including biomaterials interfaces, actuators, and soft robotics. High spatial resolution is required to impart different properties across the composite for the intended application, but many techniques used to prepare these composites rely on multistep and complex methods. There is a need for the development of simple and efficient platforms to design layered composite materials. Here, we report the synthesis of horizontally- and vertically-patterned composites consisting of PDMS-based polymerized high internal phase emulsion (polyHIPE) porous elastomers and PDMS/PEG hydrogels. Composites with defined interfaces that were mechanically robust were prepared, and rheological analysis of the polyHIPE and hydrogel layers showed storage moduli values of ∼ 35 kPa and 45 kPa respectively. The compressive Young's Modulus and maximum strain of the polyHIPEs were dependent on the thiol to ene ratio in the formulation and obtained values ranging from 6 to 25 kPa and 50-65% respectively. The mechanical properties, total porosity of the polyHIPE, and swelling ratio of the hydrogel were unaffected by the patterning technique compared to non-patterned controls. PolyHIPE-hydrogel composite materials having up to 7-different horizontally pattered layers could be prepared that could expand and contract up hydration and drying.

Non-invasive determination of ionizable ligand group density on high internal phase emulsion derived polymer

Stepwise change between low and high salt concentration buffers of the same pH results in pH transition, the length of which was demonstrated to be proportional to the quantity of ion-exchange groups present on the matrix. In this work, we analyzed the effect of the ligand type, density, and buffer concentration on the pH transition shape for typical ion-exchange groups (QA, DEAE, SO3, and COOH) and ligands acting as metal-chelators, such as IDA, TAEA, and EDA. It was demonstrated that pH transition can occur either as a chromatographic or flat-top peak. pH transition peaks were evaluated by their length, height, and peak center parameters. While no parameter can describe the ligand density accurately with a single linear correlation for both peak types, all parameters can be used for the description of one peak type. Peak length and height exhibited the same accuracy, while their sensitivity depended on the pH transition shape: length being more sensitive for the flat-top peaks, while height for the chromatographic peaks. pH height can be obtained faster, at lower elution volume, and seems to be more suitable for the determination of low amounts of ligand, when typically chromatographic peak type pH transitions occur.

Basic Principles of Emulsion Templating and Its Use as an Emerging Manufacturing Method of Tissue Engineering Scaffolds

Tissue engineering (TE) aims to regenerate critical size defects, which cannot heal naturally, by using highly porous matrices called TE scaffolds made of biocompatible and biodegradable materials. There are various manufacturing techniques commonly used to fabricate TE scaffolds. However, in most cases, they do not provide materials with a highly interconnected pore design. Thus, emulsion templating is a promising and convenient route for the fabrication of matrices with up to 99% porosity and high interconnectivity. These matrices have been used for various application areas for decades. Although this polymer structuring technique is older than TE itself, the use of polymerised internal phase emulsions (PolyHIPEs) in TE is relatively new compared to other scaffold manufacturing techniques. It is likely because it requires a multidisciplinary background including materials science, chemistry and TE although producing emulsion templated scaffolds is practically simple. To date, a number of excellent reviews on emulsion templating have been published by the pioneers in this field in order to explain the chemistry behind this technique and potential areas of use of the emulsion templated structures. This particular review focusses on the key points of how emulsion templated scaffolds can be fabricated for different TE applications. Accordingly, we first explain the basics of emulsion templating and characteristics of PolyHIPE scaffolds. Then, we discuss the role of each ingredient in the emulsion and the impact of the compositional changes and process conditions on the characteristics of PolyHIPEs. Afterward, current fabrication methods of biocompatible PolyHIPE scaffolds and polymerisation routes are detailed, and the functionalisation strategies that can be used to improve the biological activity of PolyHIPE scaffolds are discussed. Finally, the applications of PolyHIPEs on soft and hard TE as well as in vitro models and drug delivery in the literature are summarised.

Assessment of the Angiogenic Potential of 2-Deoxy-D-Ribose Using a Novel in vitro 3D Dynamic Model in Comparison With Established in vitro Assays

Angiogenesis is a highly ordered physiological process regulated by the interaction of endothelial cells with an extensive variety of growth factors, extracellular matrix components and mechanical stimuli. One of the most important challenges in tissue engineering is the rapid neovascularization of constructs to ensure their survival after transplantation. To achieve this, the use of pro-angiogenic agents is a widely accepted approach. The study of angiogenesis has gained momentum over the last two decades. Although there are various in vitro, ex vivo, and in vivo angiogenesis models that enable testing of newly discovered pro-angiogenic agents, the problem with researching angiogenesis is the choice of the most appropriate assay. In vivo assays are the most representative and reliable models, but they are expensive, time-consuming and can cause ethical concerns whereas in vitro assays are relatively inexpensive, practical, and reproducible, but they are usually lack of enabling the study of more than one aspect of angiogenesis, and they do not fully represent the complexity of physiological angiogenesis. Therefore, there is a need for the development of an angiogenesis model that allows the study of angiogenesis under physiologically more relevant, dynamic conditions without causing ethical concerns. Accordingly, in this study, we developed 3D in vitro dynamic angiogenesis model, and we tested the angiogenic potential of 2-deoxy-D-ribose (2dDR) in comparison with vascular endothelial growth factor (VEGF) using newly developed in vitro 3D dynamic model and well-established in vitro models. Our results obtained using conventional in vitro assays demonstrated that 2dDR promoted proliferation, migration and tube formation of human aortic endothelial cells (HAECs) in a dose-dependent manner. Then, the angiogenic activity of 2dDR was further assessed using the newly developed 3D in vitro model, which enabled the monitoring of cell proliferation and infiltration simultaneously under dynamic conditions. Our results showed that the administration of 2dDR and VEGF significantly enhanced the outgrowth of HAECs and the cellular density under either static or dynamic conditions.

Application of PolyHIPE Membrane with Tricaprylmethylammonium Chloride for Cr(VI) Ion Separation: Parameters and Mechanism of Transport Relating to the Pore Structure

The structural characteristics of membrane support directly affect the performance of carrier facilitated transport membrane. A highly porous PolyHIPE impregnated with Aliquat 336 is proposed for Cr(VI) separation. PolyHIPE consisting of poly(styrene-co-2-ethylhexyl acrylate) copolymer crosslinked with divinylbenzene has the pore structure characteristic of large pore spaces interconnected with small window throats. The unique pore structure provides the membrane with high flux and stability. The experimental results indicate that the effective diffusion coefficient D* of Cr(VI) through Aliquat 336/PolyHIPE membrane is as high as 1.75 × 10⁻¹¹ m² s⁻¹. Transport study shows that the diffusion of Cr(VI) through Aliquat 336/PolyHIPE membrane can be attributed to the jumping transport mechanism. The hydraulic stability experiment shows that the membrane is quite stable, with recovery rates remaining at 95%, even after 10 consecutive cycles of operation. The separation study demonstrates the potential application of this new type of membrane for Cr(VI) recovery.

Inflatable Elastomeric Macroporous Polymers Synthesized from Medium Internal Phase Emulsion Templates

Closed cell elastomeric polydimethylsiloxane (PDMS) based polymerized medium internal phase emulsions (polyMIPEs) containing an aqueous solution of sodium hydrogen carbonate (NaHCO3) have been produced. Via thermal decomposition of NaHCO3, carbon dioxide was released into the polyMIPE structure to act as a blowing agent. When placed into an atmosphere with reduced pressure, these macroporous elastomers expanded to many times their original size, with a maximum expansion of 30 times. This expansion was found to be repeatable and reproducible. The extent of volume expansion was determined primarily by the dispersed phase volume ratio of the emulsion template; polyMIPEs with 60% dispersed phase content produced greater volume expansion ratios than polyMIPEs with 50% dispersed phase. Increasing the concentration of NaHCO3 in the dispersed phase also led to increased expansion due to the greater volume of gas forming within the porous structure of the silicone elastomer. The expansion ratio could be increased by doubling the agitation time during the emulsification process to form the MIPEs, as this decreased the pore wall thickness and hence the elastic restoring force of the porous silicone elastomer. Although MIPEs with 70% dispersed phase could be stabilized and successfully cured, the resultant polyMIPE was mechanically too weak and expanded less than polyMIPEs with a dispersed phase of 60%. It was also possible to cast the liquid emulsion into thin polyMIPE films, which could be expanded in vacuum, demonstrating that these materials have potential for use in self-sealing containers.