Rapid removal of triazine pesticides by P doped biochar and the adsorption mechanism

Biochar is an adsorbent widely used to remove contaminants from polluted water. A series of biochar from corn straw, corncob and corn starch was prepared through one-step pyrolysis. The biochar was characterized, and the capacity for triazine pesticide (TRZ) removal from water was compared. P doped biochar from corn straw (CSWP) was able to remove six TRZs (>96%) from water after shaking five times. The removal was more rapid than that by four other commonly used adsorbents. The physicochemical properties of CSWP were characterized systematically, and carboxyl and metaphosphates on CSWP were found to provide adsorption sites. The experimental data were best fitted by a pseudo-second-order kinetic model and the Freundlich model. Adsorption equilibrium of atrazine on CSWP occurred within 20 min, and the maximum adsorption capacity reached up to 79.6 mg g^-1 at 25 °C. The adsorption mechanism of CSWP for atrazine includes Van der Waals' forces, hydrogen bonding, electrostatic interactions and pore filling. CSWP can be reused at least five times and shows strong potential as a candidate for the rapid and efficient removal of TRZs.

Efficient removal of perfluorinated compounds from water using a regenerable magnetic activated carbon

Adsorption by powder activated carbon (PAC) is recognized as an efficient method for the removal of perfluorinated compounds (PFCs) in water, while the poor separation of spent PAC makes it difficult for further regeneration, increasing the treatment cost significantly. In this study, an ultrafine magnetic activated carbon (MAC) consisting of Fe₃O₄ and PAC was prepared by ball milling to remove PFCs from water efficiently. Increasing the percentage of Fe₃O₄ and balling milling time decreased its adsorption capacity for perfluoroctane sulfonate (PFOS), whereas increased the magnetic separation property to some degree. The optimized MAC was prepared with a Fe₃O₄ to PAC mass ratio of 1:3 after ball milling for 2 h, and the adsorption equilibriums of all the four PFCs on the optimal MAC were reached within less than 2 h, with the adsorption capacities of 1.63, 0.90, 0.33 and 0.21 mmol/g for PFOS, perfluorooctanoic acid (PFOA), perfluorohexane sulfonate (PFHxS) and perfluorobutane sulfonate (PFBS), respectively. Increasing the solution pH hindered the adsorption of PFOS significantly when the pH was less than the zero potential point (around 6) of the MAC, due to the decreased electrostatic attraction. The spent MAC could be easily separated with a magnet and regenerated by a small volume of methanol, and the regenerated MAC could be reused for more than 5 time and remain stable adsorption capacity for PFOS after 3 cycles. This study provides useful insights into the removal of PFCs by separable magnetic PAC in wastewater.

Mesoporous activated carbon from starch for superior rapid pesticides removal

Pesticides contamination of water has caused considerable concern due to the potential hazard to human health. For the first time, mesoporous activated carbon from starch (ACS) was applied to remove pesticides from water. ACS could remove 11 pesticides rapidly (shake five times). The adsorption rates of ACS (>80%) for the 11 pesticides were higher than those of other adsorbents, including commercial activated carbon (AC), graphitised carbon black (GCB), C18, and primary secondary amine adsorbent (PSA). The mechanisms of the adsorption process for pyraclostrobin were also investigated. The pseudo-second-order model could better describe the adsorption for pyraclostrobin (R² = 0.99950). Langmuir model gave the best fit for the isotherm data (R² = 0.99899). Our findings demonstrate that oxygen-containing functional groups, N atom and π-bonding network of benzene promoted the adsorption. The adsorption efficiency of the ACS for 11 pesticides was still over 80% after five cycles.

Green synthesis of a magnetic β-cyclodextrin polymer for rapid removal of organic micro-pollutants and heavy metals from dyeing wastewater

Adsorption is one of the most preferred techniques in the advanced treatment of dyeing wastewater. Magnetic porous materials with good adsorption performance, excellent reusability, and a green synthesis route are highly desirable adsorbents in commerce. In this study, we synthesized a magnetic β-cyclodextrin polymer (MNP-CM-CDP) containing many macro- and ultramicropores in aqueous phase. CO₂ adsorption-desorption isotherms and a dye adsorption method provided Langmuir specific surface areas for the MNP-CM-CDP of 114.4 m² g^-1 and 153 m² g^-1, respectively. Model pollutants (BPA, MB, BO₂, RhB, Cr(III), Pb(II), Zn(II), and Cu(II)) were rapidly and efficiently removed from the aqueous solution by the MNP-CM-CDP. In addition, the polymer could be easily separated from the solution under an external magnetic field. The adsorption of the contaminants was dependent on pH, while the effects of ionic strength and humic acid were slight in the concentration range studied. The polymer could be easily regenerated at room temperature and retained good adsorption performance. Moreover, the MNP-CM-CDP showed good feasibility for the removal of pollutants from actual dyeing wastewater samples.

Rapid and selective recovery of acetophenone from petrochemical effluents by crosslinked starch polymer

A porous crosslinked starch polymer (CSTO) using bitolylene diisocyanate as crosslinker was prepared by a facile method and used to selectively recover acetophenone (AP) from petrochemical effluent mainly containing AP and 1-phenylethanol (PE). The theoretical calculation results indicated that AP exhibited the superior affinity toward the adsorption sites of CSTO through noncovalent interactions. The adsorption measurements showed that, due to the large surface area and high affinity of phenyl rings, CSTO displayed an extremely rapid adsorption rate, a desirable adsorption capacity and selectivity to AP. The adsorption kinetics and isotherms in single solute system agreed well with the pseudo-second-order kinetic model and Freundlich isotherm model, and the adsorption was exothermic and spontaneous. Furthermore, CSTO showed excellent reusability for selective adsorption of AP from equimolar mixture of AP/PE, prompting us to further examine its applicability. In the practical application, CSTO also revealed a fast, preferential and reusable adsorption of AP from actual petrochemical effluent.

Rapid removal of PFOA and PFOS via modified industrial solid waste: Mechanisms and influences of water matrices

Emerging perfluoroalkyl and polyfluoroalkyl substances contaminate waters at trace concentrations, thus rapid and selective adsorbents are pivotal to mitigate the consequent energy-intensive and time-consuming issues in remediation. In this study, coal combustion residuals-fly ash was modified (FA-SCA) to overcome the universal trade-off between high adsorption capacity and fast kinetics. FA-SCA presented rapid adsorption (t_eq = 2 min) of PFOX (perfluorooctanoic acid and perfluorooctanesulfonic acid, collectively), where the dynamic adsorption capacity (q_dyn = q_m/t_eq) was 2-3 orders of magnitude higher than that of benchmark activated carbons and anion-exchange resins. Investigated by advanced characterization and kinetic models, the fast kinetics and superior q_dyn are attributed to (1) elevated external diffusion driven by the submicron particle size; (2) enhanced intraparticle diffusion caused by the developed mesoporous structure (V_meso/V_micro = 8.1); (3) numerous quaternary ammonium anion-exchange sites (840 μmol/g), and (4) appropriate adsorption affinity (0.031 L/μmol for PFOS, and 0.023 L/μmol for PFOA). Since the adsorption was proven to be a synergistic process of electrostatic and hydrophobic interactions, effective adsorption ([PFOX]_ini = 1.21 μM, concentration levels of highly-contaminant-sites) was obtained at conventional natural water chemistries. High selectivity (>85.4% removal) was also achieved with organic/inorganic competitors, especially compounds with partly similar molecular structures to PFOX. In addition, >90% PFOX was removed consistently during five cycles in mild regeneration conditions (pH 12 and 50 °C). Overall, FA-SCA showed no leaching issues of toxic metals and exhibits great potential in both single-adsorption processes and treatment train systems.

Rapid adsorption of directional cellulose nanofibers/3-glycidoxypropyltrimethoxysilane/polyethyleneimine aerogels on microplastics in water

Currently, cellulose-based aerogel materials are a hot topic owing to their high specific surface area and high porosity, as well as the green, degradable and biocompatible characteristics of cellulosic materials. Modification of cellulose to enhance the adsorption properties of cellulose-based aerogels has important research significance in solving the problem of water body pollution. In this paper, cellulose nanofibers (CNFs) were modified with polyethyleneimine (PEI), and modified aerogels with directional structures were prepared by a simple reaction and freeze-drying method. The adsorption behavior of the aerogel followed the adsorption kinetic models and isotherm models. More significantly, the aerogel could rapidly adsorb microplastics, reaching equilibrium within 20 min. Furthermore, the fluorescence displayed directly expresses the occurrence of the adsorption behavior of the aerogels. Therefore, the modified cellulose nanofiber aerogels were of reference significance for microplastic removal from water bodies.

Rapid removal of ammonia nitrogen in low-concentration from wastewater by amorphous sodium titanate nano-particles

An amorphous sodium titanate (ST) nano-particle was prepared via the facile hydrolytic process with the addition of sodium hydroxide and firstly used for ammonia nitrogen (NH₃-N) removal from wastewater. ST exhibited satisfactory adsorption efficiency for NH₃-N simulative wastewater (20 mg·L^-1) at a wide range of pH 3.0-9.0, within a minimum contact time of 10 min. The Langmuir isotherm showed that the maximum adsorption capacity (298 K) of the adsorbent was reach up to 44.54 mg·g^-1. Concentrated competing cations had some interferences with NH₃-N adsorption at the order of Ca²⁺ > K⁺ > Mg²⁺ > Na⁺ according to their competition on adsorption sites. During the adsorption process, cation exchange between Na⁺ and NH₄⁺ played a powerful role for the NH₃-N removal and the contribution of Ti-OH groups was also involved in the adsorption. The regeneration test showed that the saturated adsorbents could be conveniently regenerated just by NaOH or NaCl solution treatment and there was no obvious decline of the adsorption capacity after reused for five times. The facile method of fabrication and regeneration, the rapid adsorption process and the satisfactory adsorption efficiency make sodium titanate a promising adsorbent for low concentration NH₃-N minimization.

Application of a novel polymer cross-linked with magnetite for efficient norfloxacin adsorption at a wide pH range

Nowadays, NOR-containing wastewater has placed huge pressure on global ecology. In this study, a chemically-modified chitosan-based polymer was cross-linked with magnetite to prepare a novel magnetic composite adsorbent named Fe3O4/CS-P(AM-SSS) for norfloxacin (NOR) removal. The preparation conditions were optimized by single factor experiments and response surface methodology. A series of characterization analyses were carried out on the morphology, structure, and properties of Fe3O4/CS-P(AM-SSS), verifying that Fe3O4/CS-P(AM-SSS) was successfully prepared. Batch adsorption experiments showed that NOR was efficiently removed by Fe3O4/CS-P(AM-SSS), with a broad pH applicability of 3-10, short adsorption equilibrium time of 60 min, maximum adsorption capacity of 268.79 mg/g, and high regeneration rate of 86% after eight adsorption-desorption cycles. Due to the three-dimensional network structure and abundant functional groups provided by modified chitosan polymer, the superior adsorption capability of Fe3O4/CS-P(AM-SSS) was achieved through electrostatic interaction, π-π stacking, hydrophobic interaction, and hydrogen bonding. Adsorption process was exothermic and well fitted by the pseudo-second-order kinetic model and the Langmuir isothermal model. The presence of cations had a slight inhibitory effect on NOR adsorption, while humic acid nearly had no effect. In model swine wastewater, 90.3% NOR was removed by Fe3O4/CS-P(AM-SSS). Therefore, with these superior characteristics, Fe3O4/CS-P(AM-SSS) was expected to be an ideal material for treating NOR-containing wastewater in the future.

Facile synthesis of lignin-based Fe-MOF for fast adsorption of methyl orange

To rapidly remove dyes from wastewater, iron-based metal-organic frameworks modified with phenolated lignin (NH2-MIL@L) were prepared by a one-step hydrothermal method. Analyses of the chemical structure and adsorption mechanism of the NH2-MIL@L proved the successful introduction of lignin and the enhancement of its adsorption sites. Compared with NH2-MIL-101-Fe without phenolated lignin, the modification with lignin increased the methyl orange (MO) adsorption rate of NH2-MIL@L. For the best adsorbent, NH2-MIL@L4, the MO adsorption efficiency in MO solution reached 95.09% within 5 min. NH2-MIL@L4 reached adsorption equilibrium within 90 min, exhibiting an MO adsorption capacity of 195.31 mg/g. The process followed pseudo-second-order kinetics and the Dubinin-Radushkevich model. MO adsorption efficiency of NH2-MIL@L4 was maintained at 89.87% after six adsorption-desorption cycles. In mixed solutions of MO and methylene blue (MB), NH2-MIL@L4 achieved an MO adsorption of 94.02% at 5 min and reached MO adsorption equilibrium within 15 min with an MO adsorption capacity of 438.6 mg/g, while the MB adsorption equilibrium was established at 90 min with an MB adsorption rate and capacity of 95.60% and 481.34 mg/g, respectively. NH2-MIL@L4 sustained its excellent adsorption efficiency after six adsorption-desorption cycles (91.2% for MO and 93.4% for MB). The process of MO adsorption by NH2-MIL@L4 followed the Temkin model and pseudo-second-order kinetics, while MB adsorption followed the Dubinin-Radushkevich model and pseudo-second-order kinetics. Electrostatic interactions, π-π interactions, hydrogen bonding, and synergistic interactions affected the MO adsorption process of NH2-MIL@L4.

Chlorinated volatile organic compounds (CVOCs) and 1,4-dioxane kinetics and equilibrium adsorption studies on selective macrocyclic adsorbents

Chlorinated volatile organic compounds (CVOCs) are often found in combination with 1,4-dioxane which has been used as a solvent stabilizer. It would be desirable to separate these compounds since biodegradation of 1,4-dioxane follows an aerobic pathway while anaerobic conditions are needed for biodegrading CVOCs. Conventional adsorbents such as activated carbon (AC) and carbonaceous resins have high adsorption capacities for 1,4-dioxane and CVOCs but lack selectivity, limiting their use for separation (Liu et al., 2019). In the current work, two macrocyclic adsorbents, β-CD-TFN and Res-TFN, were examined for selective adsorption of chlorinated ethenes in the presence of 1,4-dioxane. Both adsorbents exhibited rapid adsorption of the CVOCs and minimal adsorption of 1,4-dioxane. Res-TFN had a higher adsorption capacity for CVOCs than β-CD-TFN (measured linear partition coefficient, Kd 2140 -9750 L⋅kg-1 versus 192-918 L⋅kg-1 for 1,1, DCE, cis-1,2-DCE and TCE, respectively) and was highly selective for CVOCs(TCE Kd ~117 Kd for 1,4-dioxane). By comparison, TCE and 1,4-dioxane adsorption on AC was approximately equal at 100 µg⋅L-1 and approximately 1/3 of the adsorption of TCE on the Res-TFN. The greater adsorption and selectivity of Res-TFN suggest that it can be used as a selective adsorbent to separate CVOCs from 1,4-dioxane to allow separate biodegradation.

Fabricating whole pine needles biomass with phenylhydrazine-4-sulphonic acid for effective removal of cationic dyes and heavy metal ions from wastewater

We applied a holistic, sustainable, and green approach to develop an effective multipurpose adsorbent from whole pine needles (PNs), a forest waste lignocellulosic biomass. The PNs were oxidized and modified with phenylhydrazine-4-sulphonic acid (ɸHSO3H) to OPN-ɸHSO3H. The latter was characterized and tested as an adsorbent for cationic dyes, malachite green (MG), methylene blue (MB), crystal violet (CV), and metal ions (Hg2⁺ and Pb2⁺). The adsorption followed different kinetic models: Elovich for MG and MB, pseudo-second-order for CV, and pseudo-first-order for Hg2⁺ and Pb2⁺. Langmuir isotherm indicated maximum adsorption capacities of 303.4 ± 8.91 mgg-1 (MG), 331.4 ± 17.50 mgg-1 (MB), 376.6 ± 22.47 mgg-1 (CV), 210.8 ± 28.86 mgg-1 (Hg2⁺), and 172.9 ± 20.93 mgg-1 (Pb2⁺) within 30 min. Maximum removal efficiencies were 99.0% (MG), 98.0% (MB), 96.04% (CV), 95.5% (Hg2⁺), and 89.8% (Pb2⁺). The adsorbent demonstrated significant regeneration and reusability over ten cycles, proving highly efficient for both cationic dyes and metal ions, with wide potential for practical applications where more than one adsorbate is present.