A Facile "Double-Catalysts" Approach to Directionally Fabricate Pyridinic NB-Pair-Doped Crystal Graphene Nanoribbons/Amorphous Carbon Hybrid Electrocatalysts for Efficient Oxygen Reduction Reaction

Carbon material is a promising electrocatalyst for the oxygen reduction reaction (ORR). Doping of heteroatoms, the most widely used modulating strategy, has attracted many efforts in the past decade. Despite all this, the catalytic activity of heteroatoms-modulated carbon is hard to compare to that of metal-based electrocatalysts. Here, a "double-catalysts" (Fe salt, H₃ BO₃ ) strategy is presented to directionally fabricate porous structure of crystal graphene nanoribbons (GNs)/amorphous carbon doped by pyridinic NB pairs. The porous structure and GNs accelerate ion/mass and electron transport, respectively. The N percentage in pyridinic NB pairs accounts for ≈80% of all N species. The pyridinic NB pair drives the ORR via an almost 4e^- transfer pathway with a half-wave potential (0.812 V vs reversible hydrogen electrode (RHE)) and onset potential (0.876 V vs RHE) in the alkaline solution. The ORR catalytic performance of the as-prepared carbon catalysts approximates commercial Pt/C and outperforms most prior carbon-based catalysts. The assembled Zn-air battery exhibits a high peak power density of 94 mW cm^-2 . Density functional theory simulation reveals that the pyridinic NB pair possesses the highest catalytic activity among all the potential configurations, due to the highest charge density at C active sites neighboring B, which enhances the interaction strength with the intermediates in the p-band center.

CNT-Decorated Na3V2(PO4)3 Microspheres as a High-Rate and Cycle-Stable Cathode Material for Sodium Ion Batteries

A novel cathode material, carbon nanotube (CNT)-decorated Na₃V₂(PO₄)₃ (NVP) microspheres, was designed and synthesized via spray-drying and carbothermal reduction methods. The microspheres were covered and embedded by CNTs, the surfaces of which were also covered by amorphous carbon layers. Thus, a carbon network composed of CNTs and amorphous carbon layers formed in the materials. The polarization of a 10 wt % CNT-decorated NVP (NVP/C10) electrode was much less compared with that of the electrode with pristine NVP without CNTs. The capacity of the NVP/C10 electrode only decreased from 103.2 to 76.2 mAh g^-1 when the current rates increased from 0.2 to 60 C. Even when cycled at a rate of 20 C, the initial discharge capacity of the NVP/C10 electrode was as high as 91.2 mAh g^-1, and the discharge capacity was 76.9 mAh g^-1 after 150 cycles. The charge-transfer resistance and ohmic resistance became smaller because of CNT decorating. Meanwhile, the addition of CNTs can tune the size of the NVP particles and increase the contact area between NVP and the electrolyte. Consequently, the resulted NVP had a larger sodium ion diffusion coefficient than that of the pristine NVP.

A Tunable Molten-Salt Route for Scalable Synthesis of Ultrathin Amorphous Carbon Nanosheets as High-Performance Anode Materials for Lithium-Ion Batteries

Amorphous carbon is regarded as a promising alternative to commercial graphite as the lithium-ion battery anode due to its capability to reversibly store more lithium ions. However, the structural disorder with a large number of defects can lead to low electrical conductivity of the amorphous carbon, thus limiting its application for high power output. Herein, ultrathin amorphous carbon nanosheets were prepared from petroleum asphalt through tuning the carbonization temperature in a molten-salt medium. The amorphous nanostructure with expanded carbon interlayer spacing can provide substantial active sites for lithium storage, while the two-dimensional (2D) morphology can facilitate fast electrical conductivity. As a result, the electrodes deliver a high reversible capacity, outstanding rate capability, and superior cycling performance (579 and 396 mAh g^-1 at 2 and 5 A g^-1 after 900 cycles). Furthermore, full cells consisting of the carbon anodes coupled with LiMn₂O₄ cathodes exhibit high specific capacity (608 mAh g^-1 at 50 mA g^-1) and impressive cycling stability with slow capacity loss (0.16% per cycle at 200 mA g^-1). The present study not only paves the way for industrial-scale synthesis of advanced carbon materials for lithium-ion batteries but also deepens the fundamental understanding of the intrinsic mechanism of the molten-salt method.

Silicon-Core-Carbon-Shell Nanoparticles for Lithium-Ion Batteries: Rational Comparison between Amorphous and Graphitic Carbon Coatings

Silicon-core-carbon-shell nanoparticles have been widely studied as promising candidates for the replacement of graphite in commercial lithium-ion batteries. Over more than 10 years of R&D, the many groups actively working in this field have proposed a profusion of distinctive nanomaterial designs. This broad variety makes it extremely challenging to establish mechanistic insight into how fundamental material structure and properties affect battery performance. In particular, the interplay between the character of the carbon encapsulation layer and the electrochemical performance of the composite is still poorly understood. In this work, we aim to address this lack of knowledge through the development of a modified chemical vapor deposition approach that enables precise control of the degree of graphitization of the carbon coating. We provide a comparison between core-shell structures maintaining identical silicon cores with different types of carbon shells, that is, graphitic carbon and amorphous carbon. A highly graphitic carbon layer is not only characterized by higher electrical conductivity but markedly favors the transport of lithium ions into the silicon core with respect to an amorphous one. This advantageous property confers better cycling stability to the composite material. We also demonstrate that the graphitic-carbon-coated particles display excellent electrochemical performance even when used as a simple "drop-in" additive in graphite-dominant anodes for current generation Li-ion batteries. Replacement of 10% by weight of graphite in the electrode composition results in an increase of 60% in the storage capacity with a first cycle Coulombic efficiency of 91% and capacity retention over 100 cycles of 86%.

Carbon-Confined SnO2-Electrodeposited Porous Carbon Nanofiber Composite as High-Capacity Sodium-Ion Battery Anode Material

Sodium resources are inexpensive and abundant, and hence, sodium-ion batteries are promising alternative to lithium-ion batteries. However, lower energy density and poor cycling stability of current sodium-ion batteries prevent their practical implementation for future smart power grid and stationary storage applications. Tin oxides (SnO2) can be potentially used as a high-capacity anode material for future sodium-ion batteries, and they have the advantages of high sodium storage capacity, high abundance, and low toxicity. However, SnO2-based anodes still cannot be used in practical sodium-ion batteries because they experience large volume changes during repetitive charge and discharge cycles. Such large volume changes lead to severe pulverization of the active material and loss of electrical contact between the SnO2 and carbon conductor, which in turn result in rapid capacity loss during cycling. Here, we introduce a new amorphous carbon-coated SnO2-electrodeposited porous carbon nanofiber (PCNF@SnO2@C) composite that not only has high sodium storage capability, but also maintains its structural integrity while ongoing repetitive cycles. Electrochemical results revealed that this SnO2-containing nanofiber composite anode had excellent electrochemical performance including high-capacity (374 mAh g(-1)), good capacity retention (82.7%), and large Coulombic efficiency (98.9% after 100th cycle).

Robust All-Carbon Molecular Junctions on Flexible or Semi-Transparent Substrates Using "Process-Friendly" Fabrication

Large area molecular junctions were fabricated on electron-beam deposited carbon (eC) surfaces with molecular layers in the range of 2-5.5 nm between conducting, amorphous carbon contacts. Incorporating eC as an interconnect between Au and the molecular layer improves substrate roughness, prevents electromigration and uses well-known electrochemistry to form a covalent C-C bond to the molecular layer. Au/eC/anthraquinone/eC/Au junctions were fabricated on Si/SiOx with high yield and reproducibility and were unchanged by 10(7) current-voltage cycles and temperatures between 80 and 450 K. Au/eC/AQ/eC/Au devices fabricated on plastic films were unchanged by 10(7) current density vs bias voltage (J-V) cycles and repeated bending of the entire assembled junction. The low sheet resistance of Au/eC substrates permitted junctions with sufficiently transparent electrodes to conduct Raman or UV-vis absorption spectroscopy in either reflection or transmission geometries. Lithographic patterning of Au/eC substrates permitted wafer-scale integration yielding 500 devices on 20 chips on a 100 mm diameter wafer. Collectively, eC on Au provides a platform for fabrication and operation of chemically stable, optically and electrically functional molecules on rigid or flexible materials. The relative ease of processing and the robustness of molecular junctions incorporating eC layers should help address the challenge of economic fabrication of practical, flexible molecular junctions for a potentially wide range of applications.

Simultaneous Identification of Low and High Atomic Number Atoms in Monolayer 2D Materials Using 4D Scanning Transmission Electron Microscopy

Simultaneous imaging of individual low and high atomic number atoms using annular dark field scanning transmission electron microscopy (ADF-STEM) is often challenging due to substantial differences in their scattering cross sections. This often leads to contrast from only the high atomic number species when imaged using ADF-STEM such as the Mo and 2S sites in monolayer MoS₂ crystals, without detection of lighter atoms such as C, O, or N. Here, we show that by capturing an array of convergent beam electron diffraction patterns using a 2D pixelated electron detector (2D-PED) in a 4D STEM geometry enables identification of individual low and high atomic number atoms in 2D materials by multicomponent imaging. We have used ptychographic phase reconstructions, combined with angular dependent ADF-STEM reconstructions, to image light elements at lateral (nanopores) and vertical interfaces (surface dopants) within 2D monolayer MoS₂. Differential phase contrast imaging (Div(DPC)) using quadrant segmentation of the 2D pixelated direct electron detector data not only qualitatively matches the ptychographic phase reconstructions in both resolution and contrast but also offers the additional potential for real time display. Using 4D-STEM, we have identified surface adatoms on MoS₂ monolayers and have separated atomic columns with similar total atomic number into their relative combinations of low and high atomic number elements. These results demonstrate the rich information present in the data obtained during 4D-STEM imaging of ultrathin 2D materials and the ability of this approach to extract unique insights beyond conventional imaging.

Rapid Electron Beam Writing of Topologically Complex 3D Nanostructures Using Liquid Phase Precursor

Advancement of focused electron beam-induced deposition (FEBID) as a versatile direct-write additive nanoscale fabrication technique has been inhibited by poor throughput, limited choice of precursors, and restrictions on possible 3D topologies. Here, we demonstrate FEBID using nanoelectrospray liquid precursor injection to grow carbon and pure metal nanostructures via direct decomposition and electrochemical reduction of the relevant precursors, achieving growth rates 10(5) times greater than those observed in standard gas-phase FEBID. Initiating growth at the free surface of a liquid pool enables fabrication of complex 3D carbon nanostructures with strong adhesion to the substrate. Deposition of silver microstructures at similar growth rates is also demonstrated as a promising avenue for future development of the technique.

Discovery of carbon-based strongest and hardest amorphous material

Carbon is one of the most fascinating elements due to its structurally diverse allotropic forms stemming from its bonding varieties (sp, sp ² and sp ³). Exploring new forms of carbon has been the eternal theme of scientific research. Herein, we report on amorphous (AM) carbon materials with a high fraction of sp ³ bonding recovered from compression of fullerene C₆₀ under high pressure and high temperature, previously unexplored. Analysis of photoluminescence and absorption spectra demonstrates that they are semiconducting with a bandgap range of 1.5-2.2 eV, comparable to that of widely used AM silicon. Comprehensive mechanical tests demonstrate that synthesized AM-III carbon is the hardest and strongest AM material known to date, and can scratch diamond crystal and approach its strength. The produced AM carbon materials combine outstanding mechanical and electronic properties, and may potentially be used in photovoltaic applications that require ultrahigh strength and wear resistance.

Effect of π-π+ stacking on the layering of ionic liquids confined to an amorphous carbon surface

In the current paper, AFM studies were conducted on nanometer-thick ionic liquids (ILs) confined to an amorphous carbon (AC) surface, which is critical to the design of the next-generation media lubricant for hard disk drives (HDDs). The results indicated that the existence of the delocalized ring in the cation is critical to layering of ILs. Extended layering was observed only when there is imidazolium ring in the cation. When the imidazolium ring is replaced by an aliphatic moiety, "drop-on-layer" (dewetting) structure was observed. On the basis of the experimental results, we proposed that π-π+ stacking between sp(2) carbon in the AC and the imidazolium cation in the ILs is the key to the extended layering of ILs at the ILs/AC interface.

Carbon Nanostructure of Kraft Lignin Thermally Treated at 500 to 1000 °C

Kraft lignin (KL) was thermally treated at 500 to 1000 °C in an inert atmosphere. Carbon nanostructure parameters of thermally treated KL in terms of amorphous carbon fraction, aromaticity, and carbon nanocrystallites lateral size (L_a), thickness (L_c), and interlayer space (d₀₀₂) were analyzed quantitatively using X-ray diffraction, Raman spectroscopy, and high-resolution transmission electron microscopy. Experimental results indicated that increasing temperature reduced amorphous carbon but increased aromaticity in thermally treated KL materials. The L_c value of thermally treated KL materials averaged 0.85 nm and did not change with temperature. The d₀₀₂ value decreased from 3.56 Å at 500 °C to 3.49 Å at 1000 °C. The L_a value increased from 0.7 to 1.4 nm as temperature increased from 500 to 1000 °C. A nanostructure model was proposed to describe thermally treated KL under 1000 °C. The thermal stability of heat treated KL increased with temperature rising from 500 to 800 °C.

Carbon-Based Nanomaterials from Biopolymer Lignin via Catalytic Thermal Treatment at 700 to 1000 °C

We report the preparation of carbon-based nanomaterials from biopolymer kraft lignin via an iron catalytic thermal treatment process. Both the carbonaceous gases and amorphous carbon (AC) from lignin thermal decomposition were found to have participated in the formation of graphitic-carbon-encapsulated iron nanoparticles (GCEINs). GCEINs originating from carbonaceous gases have thick-walled graphitic-carbon layers (10 to 50) and form at a temperature of 700 °C. By contrast, GCEINs from AC usually have thin-walled graphitic-carbon layers (1 to 3) and form at a temperature of at least 800 °C. Iron catalyst nanoparticles started their phase transition from α-Fe to γ-Fe at 700 °C, and then from γ-Fe to Fe₃C at 1000 °C. Furthermore, we derived a formula to calculate the maximum number of graphitic-carbon layers formed on iron nanoparticles via the AC dissolution-precipitation mechanism.

Reduced Graphene Oxide Decorated Na3V2(PO4)3 Microspheres as Cathode Material With Advanced Sodium Storage Performance

Reduced graphene oxide (rGO) sheet decorated Na₃V₂(PO₄)₃ (NVP) microspheres were successfully synthesized by spray-drying method. The NVP microspheres were embedded by rGO sheets, and the surface of the particles were coated by rGO sheets and amorphous carbon. Thus, the carbon conductive network consisted of rGO sheets and amorphous carbon generated in the cathode material. NVP microspheres decorated with different content of rGO (about 0, 4, 8, and 12 wt%) were investigated in this study. The electrochemical performance of NVP exhibited a significant enhancement after rGO introduction. The electrode containing about 8 wt% rGO (NVP/G8) showed the best rate and cycle performance. NVP/G8 electrode exhibited the discharge capacity of 64.0 mAh g⁻¹ at 70°C, and achieved high capacity retention of 95.5% after cycling at 10°C for 100 cycles. The polarization of the electrode was inhibited by the introduction of rGO sheets. Meanwhile, compared with the pristine NVP electrode, NVP/G8 electrode exhibited small resistance and high diffusion coefficient of sodium ions.

Nb-C nanocomposite films with enhanced biocompatibility and mechanical properties for hard-tissue implant applications

One of the key challenges in engineering of orthopedic implants is to "bioactivate" their surface by using different surface techniques and materials. Carbon, especially amorphous (a-C) and diamond-like carbon down (DLC) films have attracted much attention in biomedical fields due to their biocompatibility and low coefficient of friction. However, they are unsuitable for uses as a "bioactivity enhancer" of orthopedic implants due to their bioinertness. In this work, we use the nonreactive magnetron sputtering technique to produce a-C films including the biocompatible niobium (Nb) element to alter the surface chemistry and nanotopography of the a-C films with the purpose of bioactivating the a-C film coated implants. Results show that the nanocomposite films (Nb-C) formed by the addition of Nb into the a-C films not only have improved corrosion resistance, but also possess enhanced mechanical properties (nanohardness, Young's modulus and superelastic recovery). Preosteoblasts (MC3T3-E1) cultured on the Nb-C films have enhanced adhesion and upregulated alkaline phosphatase (ALP) activity, compared to those cultured on the a-C film and TiO2 films used as a control, which are thought to be ascribed to the combined effects of the changes in surface chemistry and the refinement of the nanotopography caused by the addition of Nb.

Radiation-Induced Nucleation of Diamond from Amorphous Carbon: Effect of Hydrogen

Electron irradiation of anthracite functionalized by dodecyl groups leads to recrystallization of the carbon network into diamonds. The diamonds range in size from ∼2 to ∼10 nm and exhibit {111} spacing of 2.1 Å. A bulk process consistent with bias-enhanced nucleation is proposed in which the dodecyl group provides hydrogen during electron irradiation. Recrystallization into diamond occurs in the hydrogenated graphitic subsurface layers. Unfunctionalized anthracite could not be converted into diamond during electron irradiation. The dependence of the phase transition pressure on cluster size was estimated, and it was found that diamond particles with a radius up to 20 nm could be formed.

Amorphous Carbon-Derived Nanosheet-Bricked Porous Graphite as High-Performance Cathode for Aluminum-Ion Batteries

Graphite is an attractive cathode material for energy storage because it allows reversible intercalation/deintercalation of many compound anions at high potentials. However, because the sizes of the compound anions are greatly larger than the lamellar spacing of graphite, common graphite used as cathode may suffer from slow kinetics and large volume expansion. Here, it is demonstrated that graphite with high crystallinity and nanosheet-bricked porous structure can be an excellent cathode for aluminum-ion batteries. This porous graphite is derived from carbon black via a simple electrochemical graphitization in molten CaCl₂, and the high crystallinity and thin layer characters facilitate the high capacity and high rate storage of aluminum tetrachloride ions. Moreover, the bricked porous structure endows the fabricated cathode with a providential porosity to perfectly match the huge volume expansion of graphite (650% against a charging capacity of 100 mA h g^-1), thus this electrochemical graphite exhibits integrated high gravimetric and volumetric capacities as well as high structural stability during cycling.

Low-temperature synthesis of multilayer graphene/amorphous carbon hybrid films and their potential application in solar cells

The effect of reaction temperature on the synthesis of graphitic thin film on nickel substrate was investigated in the range of 400°C to 1,000°C. Amorphous carbon (a-C) film was obtained at 400°C on nickel foils by chemical vapor deposition; hybrid films of multilayer graphene (MLG) and a-C were synthesized at a temperature of 600°C, while MLG was obtained at temperatures in excess of 800°C. Schottky-junction solar cell devices prepared using films produced at 400°C, 600°C, 800°C, and 1,000°C coupled with n-type Si demonstrate power conversion efficiencies of 0.003%, 0.256%, 0.391%, and 0.586%, respectively. A HNO3 treatment has further improved the efficiencies of the corresponding devices to 0.004%, 1.080%, 0.800%, and 0.820%, respectively. These films are promising materials for application in low-cost and simple carbon-based solar cells.

Amorphous Carbon Generation as a Photocatalytic Reaction on DNA-Assembled Gold and Silver Nanostructures

Background signals from in situ-formed amorphous carbon, despite not being fully understood, are known to be a common issue in few-molecule surface-enhanced Raman scattering (SERS). Here, discrete gold and silver nanoparticle aggregates assembled by DNA origami were used to study the conditions for the formation of amorphous carbon during SERS measurements. Gold and silver dimers were exposed to laser light of varied power densities and wavelengths. Amorphous carbon prevalently formed on silver aggregates and at high power densities. Time-resolved measurements enabled us to follow the formation of amorphous carbon. Silver nanolenses consisting of three differently-sized silver nanoparticles were used to follow the generation of amorphous carbon at the single-nanostructure level. This allowed observation of the many sharp peaks that constitute the broad amorphous carbon signal found in ensemble measurements. In conclusion, we highlight strategies to prevent amorphous carbon formation, especially for DNA-assembled SERS substrates.

Hierarchical Mn₂O₃ Microspheres In-Situ Coated with Carbon for Supercapacitors with Highly Enhanced Performances

Porous Mn₂O₃ microspheres have been synthesized and in-situ coated with amorphous carbon to form hierarchical C@Mn₂O₃ microspheres by first producing MnCO₃ microspheres in solvothermal reactions, and then annealing at 500 °C. The self-assembly growth of MnCO₃ microspheres can generate hollow structures inside each of the particles, which can act as micro-reservoirs to store biomass-glycerol for generating amorphous carbon onto the surfaces of Mn₂O₃ nanorods consisting of microspheres. The C@Mn₂O₃ microspheres, prepared at 500 °C, exhibit highly enhanced pseudocapacitive performances when compared to the particles after annealed at 400 °C and 600 °C. Specifically, the C@Mn₂O₃ microspheres prepared at 500 °C show high specific capacitances of 383.87 F g⁻¹ at current density of 0.5 A g⁻¹, and excellent cycling stability of 90.47% of its initial value after cycling for 5000 times. The asymmetric supercapacitors assembled with C@Mn₂O₃ microspheres after annealed at 500 °C and activated carbon (AC) show an energy density of up to 77.8 Wh kg⁻¹ at power density of 500.00 W kg⁻¹, and a maximum power density of 20.14 kW kg⁻¹ at energy density of 46.8 Wh kg⁻¹. We can attribute the enhanced electrochemical performances of the materials to their three-dimensional (3D) hierarchical structure in-situ coated with carbon.

Composition-dependent structure of polycrystalline magnetron-sputtered V-Al-C-N hard coatings studied by XRD, XPS, XANES and EXAFS

V-Al-C-N hard coatings with high carbon content were deposited by reactive radio-frequency magnetron sputtering using an experimental combinatorial approach, deposition from a segmented sputter target. The composition-dependent coexisting phases within the coating were analysed using the complementary methods of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), X-ray absorption near-edge spectroscopy (XANES) and extended X-ray absorption fine-structure spectroscopy (EXAFS). For the analysis of the X-ray absorption near-edge spectra, a new approach for evaluation of the pre-edge peak was developed, taking into account the self-absorption effects in thin films. Within the studied composition range, a mixed face-centred cubic (V,Al)(C,N) phase coexisting with a C-C-containing phase was observed. No indication of hexagonal (V,Al)(N,C) was found. The example of V-Al-C-N demonstrates how important a combination of complementary methods is for the detection of coexisting phases in complex multi-element coatings.

Photoelectrocatalytic degradation of carbamazepine using Ti/TiO2 nanostructured electrodes deposited by means of a pulsed laser deposition process

The objective of the present work is to evaluate the potential of photoelectrocatalytic oxidation (PECO) process using Ti/TiO2 for the degradation of carbamazepine (CBZ). Ti/TiO2 prepared by pulsed laser deposition (PLD) has been used as a photo-catalyst in a photoelectrocatalytic cell. The PLD TiO2 coatings were found to be of anatase structure consisting of nanocrystallites of approximately 15nm in diameter. Factorial and central and extreme composite design methodologies were successively employed to define the optimal operating conditions for CBZ degradation. Several factors such as current intensity, treatment time, pollutant concentration and cathode material were investigated. Using a 2(4) factorial matrix, the best performance for CBZ degradation (53.5%) was obtained at a current intensity of 0.1 A during 120min of treatment time and when the vitreous carbon (VC) was used at the cathode in the presence of 10mgL(-1) of CBZ. Treatment time and pollutant concentration were found to be very meaningful for CBZ removal. The PECO process applied under optimal conditions (at current intensity of 0.3A during 120min in the presence of 10mgL(-1) of CBZ with VC at the cathode) is able to oxidize around 73.5% ±2.8% of CBZ and to ensure 21.2%±7.7% of mineralization. During PECO process, CBZ was mainly transformed to acridine and anthranilic acid. Microtox biotests (Vibrio fisheri) showed that the treated - effluent was not toxic. The pseudo-second order kinetic model (k2=6×10(-4)Lmg(-1)min(-1)) described very well the oxidation of CBZ.

Diverse Phases of Carbonaceous Materials from Stochastic Simulations

Amorphous carbon systems are emerging to have unparalleled properties at multiple length scales, making them the preferred choice for creating advanced materials in many sectors, but the lack of long-range order makes it difficult to establish structure/property relationships. We propose an original computational approach to predict the morphology of carbonaceous materials for arbitrary densities that we apply here to graphitic phases at low densities from 1.15 to 0.16 g/cm³, including glassy carbon. This approach, dynamic reactive massaging of the potential energy surface (DynReaxMas), uses the ReaxFF reactive force field in a simulation protocol that combines potential energy surface (PES) transformations with global optimization within a multidescriptor representation. DynReaxMas enables the simulation of materials synthesis at temperatures close to experiment to correctly capture the interplay of activated vs entropic processes and the resulting phase morphology. We then show that DynReaxMas efficiently and semiautomatically produces atomistic configurations that span wide relevant regions of the PES at modest computational costs. Indeed, we find a variety of distinct phases at the same density, and we illustrate the evolution of competing phases as a function of density ranging from uniform vs bimodal distributions of pore sizes at higher and intermediate density (1.15 g/cm³ and 0.50 g/cm³) to agglomerated vs sparse morphologies, further partitioned into boxed vs hollow fibrillar morphologies, at lower density (0.16 g/cm³). Our observations of diverse phases at the same density agree with experiment. Some of our identified phases provide descriptors consistent with available experimental data on local density, pore sizes, and HRTEM images, showing that DynReaxMas provides a systematic classification of the complex field of amorphous carbonaceous materials that can provide 3D structures to interpret experimental observations.

Reduction of Photoluminescence Quenching by Deuteration of Ytterbium-Doped Amorphous Carbon-Based Photonic Materials

In situ Yb-doped amorphous carbon thin films were grown on Si substrates at low temperatures (<200 °C) by a simple one-step RF-PEMOCVD system as a potential photonic material for direct integration with Si CMOS back end-of-line processing. Room temperature photoluminescence around 1 µm was observed via direct incorporation of optically active Yb³⁺ ions from the selected Yb(fod)₃ metal-organic compound. The partially fluorinated Yb(fod)₃ compound assists the suppression of photoluminescence quenching by substitution of C-H with C-F bonds. A four-fold enhancement of Yb photoluminescence was demonstrated via deuteration of the a-C host. The substrate temperature greatly influences the relative deposition rate of the plasma dissociated metal-organic species, and hence the concentration of the various elements. Yb and F incorporation are promoted at lower substrate temperatures, and suppressed at higher substrate temperatures. O concentration is slightly elevated at higher substrate temperatures. Photoluminescence was limited by the concentration of Yb within the film, the concentration of Yb ions in the +3 state, and the relative amount of quenching due to the various de-excitation pathways associated with the vibrational modes of the host a-C network. The observed wide full-width-at-half-maximum photoluminescence signal is a result of the variety of local bonding environments due to the a-C matrix, and the bonding of the Yb³⁺ ions to O and/or F ions as observed in the X-ray photoelectron spectroscopy analyses.

Hybrid Material Based on an Amorphous-Carbon Matrix and ZnO/Zn for the Solar Photocatalytic Degradation of Basic Blue 41

Innovative composites based on an amorphous-carbon matrix containing a second phase ZnO oxide and/or highly dispersed Zn metallic were synthesized via a modified Pechini route, in which a partial pyrolysis method was reached. Studies of adsorption in the dark and the photocatalytic activity for the cationic azo-dye, basic blue 41, and degradation were carried out. X-ray diffraction patterns for the carbon matrix and its composite with Zn show characteristics of the amorphous carbon. The infrared in the mid region of the composite prepared with ZnO and Zn exhibit vibrational bands related to bonds zinc oxide. The surface pH of the material is the main factor responsible for the adsorption of the azo-dye, but the contribution of mesopores favored the diffusion of molecules from the bulk of solution to the pore framework. Esters-like functional groups on the surface of carbons hinder the adsorption of the azo-dye. When Zn is embedded within amorphous carbon the photocatalytic activity of the composites showed up to 2.4 higher than neat ZnO. The enhancement in the photocatalytic activity and stability of C/ZnO/Zn and C/Zn composites is discussed in terms of a protector effect by the carbon layers inserted in composites. Carbon layers are responsible to inhibit the lixiviation of ZnO particles along irradiation.

Synthesis of amorphous and graphitized porous nitrogen-doped carbon spheres as oxygen reduction reaction catalysts

Amorphous and graphitized nitrogen-doped (N-doped) carbon spheres are investigated as structurally well-defined model systems to gain a deeper understanding of the relationship between synthesis, structure, and their activity in the oxygen reduction reaction (ORR). N-doped carbon spheres were synthesized by hydrothermal treatment of a glucose solution yielding carbon spheres with sizes of 330 ± 50 nm, followed by nitrogen doping via heat treatment in ammonia atmosphere. The influence of a) varying the nitrogen doping temperature (550-1000 °C) and b) of a catalytic graphitization prior to nitrogen doping on the carbon sphere morphology, structure, elemental composition, N bonding configuration as well as porosity is investigated in detail. For the N-doped carbon spheres, the maximum nitrogen content was found at a doping temperature of 700 °C, with a decrease of the N content for higher temperatures. The overall nitrogen content of the graphitized N-doped carbon spheres is lower than that of the amorphous carbon spheres, however, also the microporosity decreases strongly with graphitization. Comparison with the electrocatalytic behavior in the ORR shows that in addition to the N-doping, the microporosity of the materials is critical for an efficient ORR.