Fluorinated Polyimide Tunneling Layer for Efficient and Stable Perovskite Photovoltaics

Despite the remarkable progress of perovskite solar cells (PSCs), challenges remain in terms of finding effective and viable strategies to enhance their long-term stability while maintaining high efficiency. In this study, a new insulating and hydrophobic fluorinated polyimide (FPI: 6FDA-6FAPB) was used as the interface layer between the perovskite layer and the hole transport layer (HTL) in PSCs. The functional groups of FPI play a pivotal role in passivating interface defects within the device. Due to its high work function, FPI demonstrates field-effect passivation (FEP) capabilities as an interface layer, effectively mitigating non-radiative recombination at the interface. Notably, the FPI insulating interface layer does not impede carrier transmission at the interface, which is attributed to the presence of hole tunneling effects. The optimized PSCs achieve an outstanding power conversion efficiency (PCE) of 24.61 % and demonstrate excellent stability, showcasing the efficacy of FPI in enhancing device performance and reliability.

Preparation, Air Filtration Performance of a Fluorinated Polyimide/Polyacrylonitrile Nanofibrous Membrane by Electrospinning

This paper reports the successful fabrication of a new nanofibrous membrane, F-PI/PAN, through electrospinning of polyacrylonitrile (PAN) and fluorinated polyimide (F-PI). The nanofibrous membrane exhibits comprehensive properties for high-temperature filtration and robust PM2.5 (particulate matter with an aerodynamic equivalent diameter of 2.5 microns or less) removal. The introduction of F enhances the hydrophobicity of the PI. The relationship between the hydrophobic performance and the filtration performance of particles is investigated. The chemical group of the composite membrane was demonstrated using FITR, while the surface morphology was investigated using field emission scanning electron microscopy. The TGA results indicated good thermal stability at 300 °C. Various ratios of F-PI membranes were prepared to characterize the change in properties, with the optimal mass ratio of F-PI being 20 wt%. As the proportion of F-PI increases, its mechanical and filtration efficiency properties and hydrophobicity become stronger. The contact angle reaches its maximum of 128 ± 5.2° when PAN:F-PI = 6:4. Meanwhile, when PAN:F-PI = 8:2, the filtration efficiency reaches 99.4 ± 0.3%, and the elongation at break can reach 76%. The fracture strength can also reach 7.1 MPa, 1.63 times that of the pure PAN membrane.

Controlling Fluorination Density of Soluble Polyimide Gate Dielectrics and its Influence on Organic Crystal Growth and Device Operational Stability

Fluorinated polyimides (PIs) are among the most promising candidates for gate dielectric materials in organic electronic devices because of their solution processability and outstanding chemical, mechanical, and thermal stabilities. Additionally, fluorine (F) substitution improves the electrical properties of PI thin films, such as enhanced dielectric properties and reduced surface trap densities. However, the relationship between the fluorination density of PIs and crystal growth modes of vacuum-deposited conjugated molecules on PI thin films, which is directly related to the lateral charge transport along the PI-organic semiconductor interface, has not been systematically studied. Herein, five different soluble PIs with different F densities were synthesized, and the correlation between fluorination and thin-film properties was systematically investigated. Not only were their dielectric properties modulated, but the growth modes of the organic molecules deposited on the PI thin films also changed with increasing surface F density. This phenomenon was observed by both surface and crystallographic analyses, which resulted in extremely high operational stability of field-effect transistors and the successful fabrication of organic complementary circuits. We believe that the correlation between PI backbone fluorination and its thin-film properties will provide practical insights into the material design based on controlled molecular directed surface assembly on fluorinated polymer dielectrics.

A Fluorinated Polyimide Based Nano Silver Paste with High Thermal Resistance and Outstanding Thixotropic Performance

Because of high conductivity, acceptable cost and good screen-printing process performance, silver pastes have been extensively used for making flexible electronics. However, there are few reported articles focusing on high heat resistance solidified silver pastes and their rheological properties. In this paper, a fluorinated polyamic acids (FPAA) is synthesized by polymerization of the 4,4'-(hexafluoroisopropylidene) diphthalic anhydride and 3,4'-diaminodiphenylether as monomers in the diethylene glycol monobutyl. The nano silver pastes are prepared by mixing the obtained FPAA resin with nano silver powder. The agglomerated particles caused by nano silver powder are divided and the dispersion of nano silver pastes are improved by three-roll grinding process with low roll gaps. The obtained nano silver pastes possess excellent thermal resistance with 5% weight loss temperature higher than 500 °C. The volume resistivity of cured nano silver paste achieves 4.52 × 10^-7 Ω·m, when the silver content is 83% and the curing temperature is 300 °C. Additionally, the nano silver pastes have high thixotropic performance, which contributes to fabricate the fine pattern with high resolution. Finally, the conductive pattern with high resolution is prepared by printing silver nano pastes onto PI (Kapton-H) film. The excellent comprehensive properties, including good electrical conductivity, outstanding heat resistance and high thixotropy, make it a potential application in flexible electronics manufacturing, especially in high-temperature fields.

Frequency Response of Thermo-Optic Phase Modulators Based on Fluorinated Polyimide Polymer Waveguide

Polymer waveguide phase modulators exhibit stable low-power phase modulation owing to their exceptional thermal confinement and high thermo-optic effect, and thus, have the merit of thermal isolation between channels, which is crucial for an optical phased array (OPA) beam scanner device. In this work, a waveguide phase modulator was designed and fabricated based on a high-refractive-index fluorinated polyimide. The propagation loss of the polyimide waveguide and the temporal response of the phase modulator were characterized. Moreover, the transfer function of the phase modulator including multiple poles and zeros was obtained from the measured frequency response. The polyimide waveguide modulator device demonstrated a fast response time of 117 μs for 1 kHz input signal, however, for 1 mHz step-function input, it exhibited an additional 5% phase change in 5 s.

Highly Soluble Fluorinated Polyimides Synthesized with Hydrothermal Process towards Sustainable Green Technology

Polyimides, a widely used engineering plastic, require use of large amounts of toxic and hazardous organic solvents which threaten our daily lives, calling for new and easy synthetic methods for sustainable environmentally friendly development. In this paper, highly soluble fluorinated polyimides based on 4,4'-(hexafluoroisopropylidene) diphthalic anhydride were synthesized via hydrothermal process without using any toxic organic solvents and the advantages of the newly demonstrated synthetic methods are shown by comparative analysis performed with the two conventional synthetic methods using organic solvent: thermal and chemical imidization. Lower temperature is required (~200 °C) compared to thermal imidization and functional groups for high fusibility formed more easily compared to chemical imidization. According to the comparative analysis, hydrothermally synthesized PIs showed excellent solubility and maintained high thermal stability (>500 °C) and glass transition temperature (>300 °C) compared to conventional PI. The hydrothermally synthesized polyimide is much more convenient to store and manage than other form of polyimide which is much more stable when it is exposed to humidity as it is a powder form. The hydrothermal synthetic method is verified to be a "Green" and facile method for sustainable PI synthesis.

Transparent and Colorless Polyimides Containing Multiple Trifluoromethyl Groups as Gate Insulators for Flexible Organic Transistors with Superior Electrical Stability

A suitable insulating polymer material that is compatible with the fabrication process of organic transistors and has excellent electrical properties is critically required for the next-generation flexible organic electronics. In this study, using a one-step polymerization method, we synthesized two different solution-processable polyimides (PIs) incorporated with abundant trifluoromethyl groups. Not only were the two resulting PIs-termed 6FDA-6FDAM-PI and 6FDA-TFMB-PI-well soluble in organic solvents, but also they showed transparent and colorless optical properties. The fluorinated PI films showed smooth surface topographies and surface energy values that were appropriate for their use in bottom-gate organic transistors. Organic transistors separately fabricated with 6FDA-6FDAM-PI and 6FDA-TFMB-PI as the gate insulators showed excellent device performance and electrical stability under various testing conditions, especially for pentacene-based devices. The excellent performance of the devices with fluorinated PIs was attributed to the enhanced microstructure of the organic semiconductor and the fluorine-rich characteristic of the underlying gate insulator. Furthermore, organic complementary circuits including the basic logic gates of NOT, NOR, and NAND were demonstrated using these devices.

Fluorinated polyimide gate dielectrics for the advancing the electrical stability of organic field-effect transistors

Organic field-effect transistors (OFETs) that operated with good electrical stability were prepared by synthesizing fluorinated polyimide (PI) gate dielectrics based on 6FDA-PDA-PDA PI and 6FDA-CF3Bz-PDA PI. 6FDA-PDA-PDA PI and 6FDA-CF3Bz-PDA PI contain 6 and 18 fluorine atoms per repeat unit, respectively. These fluorinated polymers provided smooth surface topographies and surface energies that decreased as the number of fluorine atoms in the polymer backbone increased. These properties led to a better crystalline morphology in the semiconductor film grown over their surfaces. The number of fluorine atoms in the PI backbone increased, the field-effect mobility improved, and the threshold voltage shifted toward positive values (from -0.38 to +2.21 V) in the OFETs with pentacene and triethylsilylethynyl anthradithiophene. In addition, the highly fluorinated polyimide dielectric showed negligible hysteresis and a notable gate bias stability under both a N2 environment and ambient air.